Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

WC Weekend Accomplishments.....

Posts

WC Weekend Accomplishments.....

#1

WC Weekend Accomplishments.....

Dennis E Peacock

29 Aug 2011

Good Morning Everyone,

To all of my east coast ww'ing friends/families/associates, I offer your my prayers for a quick recovery for all of you. The weather here has been hot and dry. We've been blessed with some rain and cooler temps have moved in for a bit and that has been a welcomed break from the heat.

My 10 year old J.D. lawn mower is finally giving up on me. I spent almost $600 2 years ago hoping to get more out of it and I did...2 more years. This time, I'm looking at getting a Zero Turn mower. My SIL sells Toro with the Kawasaki V-Twin motors in them. I will go and see them today.

The story on my dad is that he's getting a lot more frail and his memory is now going. The hospice care nurse says that she's not sure if it's from the disease (bone cancer) or from the medication....or both. My mom is stressed out to the max and now I'm back into the planning stages of going to stay with them for a week to see what all I can do to help them. I've had 4 trips to stay so far this year and I am very thankful for my motorcycle that saves me almost 60% on fuel costs on these 800 mile round trips to help my parents.

The temps are getting cool enough to stir the desire for me to get back in the shop, but due to family medical issues and work, my time has gotten even more limited and I simply have chosen family over woodworking. I will continue the Weekend Accomplishments posts and I will keep up as best I can, but I really need to focus on family for a while now. I know my ww'ing family/friends will understand. I mean, it's not like I've done a lot of ww'ing in the past 2 years any way.

All of you are in my heart and in my prayers. Remember me and my family when you can.

Well, that's it for me...so what did you do this past weekend??

Best of weeks to you all.

Dennis Peacock

Re: WC Weekend Accomplishments.....

#2

Dennis, You Have a FULL Plate

George Colonel's Workshop-Havertown PA

Good Afternoon Dennis,

Your priorities are certainly right. That is a long round trip via motorcycle to visit your Dad. I hope he is not in much pain.

We had a hurricane-dud here. Lots of damage to be sure, but not at the level hyped by the media. Flooding is surely a problem as our ground has been saturated since long before the storm. I am glad its over, and the TV people have something to shut up about.

Whilst braving the threat of total doom and flooded basement, I did quite a bit more stock preparation, thickness planeing cherry and poplar. Yesterday I laid out the dadoes for the dust panels and began routing them with an "on-point" jig across the interior side panels. All went well until the carbide parted company with a flute of my 3/4" Jesada straight bit. That screwed up one of the channels badly, and I did not notice the cause until I had screwed up the next groove. Poor eyesight will do it every time. I'm switching to a dado blade in the table saw to finish it all up after making repairs.

No family party on Sunday Night. Two of my sons are out of town, school begins for other families, and the rest were as tired as their sump pumps.

Have a great week, Dennis

George

Re: WC Weekend Accomplishments.....

#3

Made some bells

Thomas S Stockton

Stopped by a garage sale and bought 3 old air tanks and made bells out of them, the 4th one in the back I made a while ago out of a fire extinguisher.

Tom


Re: WC Weekend Accomplishments.....

#4

Have a "fat" XL welding tank for at

Gary Smyth

least two years. The valve is open and it is empty (I think). I don't know what was in it to begin. How do I tell for certain it is safe to cut and the guy I bought it from refuses to cut the bottom out. Neither will anyone else. 1. How can I be sure it is safe? 2. How can i get a nice clean cut on the bottom? It will liikely be + or - 100 lbs when cut. I want to fit an eye bolt in the top and ring it with a mallet.

Re: WC Weekend Accomplishments.....

#5

A recent weekend's accomplishment

Nathan

Hi Dennis:

This weekend I finished the design of the Jeweler's Workbench I'm supposed to make for my wife - see my thread entitled "Advice requested".

That's not much of an accomplishment, but two weekends ago my wife and I drove to a very scenic part of the Czech Republic (called Jesenik) for a woodworking workshop. Among another things there was a sharpening demonstration:


My goal for the workshop was to relax and enjoy myself, so for my project I chose something that I've been meaning to do for years: carve a replacement tote for the old No. 5 bench plane I bought years ago (the original rosewood tote cracked in two):


The teacher at the workshop gave me a nice piece of Plum to work the new tote from. I finished it with "Danish Oil", which really brought out the beauty of the wood.

At the workshop I bought some spokeshaves, a Japanese saw, and a one-liter bottle of BLO.

Re: WC Weekend Accomplishments.....

#6

Bench plane question

Nathan

By the way, I was wondering about my plane - it looks exactly like this Stanley Type 4:


EXCEPT:

(1) Instead of "BAILEY" at the front the casting reads "MADE IN U.S.A."

(2) There are no other markings on the casting anywhere, other than at the rear of the plane, where it says "No 5".

(3) The bottom of the frog says "1828":




Since it has the lateral adjustment lever, it's not a collector's item, but it does appear to be quite old.

Re: WC Weekend Accomplishments.....

#7

Re: WC Weekend Accomplishments.....

Larry in NW Ohio

Dennis I kind of went through with my Mother that you are going through with your Father. Only with her it was Dementha, but I was a lot closer. I`ll make sure I say a few prayers for your Father and you and your family. May GOD bless you and your family. Larry

Re: WC Weekend Accomplishments.....

#8

Re: Have a "fat" XL welding tank for at

Thomas S Stockton

I cut mine with a jigsaw, drill a starter hole and cut to a marked line than clean up with an angle grinder.

No idea about welding cylinders, there is something about acetylene cylinders I remember, like they have acetone in them or something that helps keep the gas flowing. I don't remember but would be hesitant to cut anything that had something explosive in it.

try www.weldtalk.com or www.hobartwelders.com and they might answer the question

Tom

Re: WC Weekend Accomplishments.....

#9

Insulation Done!

John McGaw

Well, after getting all of the itch fiberglass and phony 'reflective' insulation ripped out over the previous two weekends I finished my plastic wrapping and masking of critical woodworking and storage assets last weekend and called the insulation contractor this morning I was surprised to have him say that they could come out in an hour. Well, they didn't quite make that and when they did get here it took them a very long time and some wildly improbable driving to get their towed rig into my driveway. After 30 minutes and 30 attempts they gave up trying to back in and pulled in forward hoping that backing down would be easier. It wasn't, not really, but the boss who was trying to back the truck in was gone by then and the Hispanic workers who were left behind to do the dirty work then had the dirty job of trying to back the long trailer and truck down my wicked driveway. Oh well, plants can be re-planted...

Anyway I now have 2" of sprayed-in closed cell foam in the joists above the garage/shop. A very messy procedure -- I'd suggest that if you want it then have it done during construction and not after the fact. Also, don't try to sneak in and take a video of the job being done using your expensive smart phone since there WILL be overspray and it WILL at least leave little spots on your phone which are near impossible to take off by any means known to man.

Of course this means that I've got to go in and hang 5/8" fire rated drywall on the ceilings and that idea doesn't please me over much either...

Re: WC Weekend Accomplishments.....

#10

Acetylene tanks have acetone and....

Dick Coers

diatomaceous earth in them to keep the gas stable. The old tanks were supposed to have asbestos in them. How fun, explosive gas in a carcinogen!

Re: WC Weekend Accomplishments.....

#11

Look at it this way...

John in NM

If it explodes and scatters asbestos dust all over you, it will probably be too late to worry about the long term effects :D

Re: WC Weekend Accomplishments.....

#12

Jesper, Denmark

Re: Belated mid-life crisis???

Jesper, Denmark


Finally hit the buy switch on a new toy.

Re: WC Weekend Accomplishments.....

#13

nice tote!

Bill Tindall

The one I made looked like beavers chewed it into shape....more or less.

Re: WC Weekend Accomplishments.....

#14

It's even the right color for a mid-life crisis

Bill Houghton, Sebastopol, CA

Mid-life crisis vehicles have to be red - it's in the rules somewhere.

Nice looking critter.

Re: WC Weekend Accomplishments.....

#15

Not wood working but...

Gary Camp, Bend Oregon

I took two of our horses to the Oregon State Fair Horse Show. It was the first time I "soloed" a horse show, well not really there were so many friends I wasn't really alone. Lisa had to work so I went by myself. I showed one horse in a couple of halter classes. One horse on western plaesure and dressage suitability. I didn't fall off and I had a lot of fun, so it was a sucessful weekend.

glc

Re: WC Weekend Accomplishments.....

#16

Jesper, Denmark

Re: Brung it home today....

Jesper, Denmark

60 miles across the Great Belt suspension Bridge. Even mixture of pelting rain, gale across the bridge and clear sunshine at the end. I felt klutzy at first, but it improved - not bad since last time I piloted a MC was more than 40 years ago. It did not have 100 HP either.

Everything worked great, and I will get the little quircks worked out. Only little minus was that the gloves are not waterproof.

This 19 year old machine will do all that this retiree needs in that department - and then some.

The reactions from this folly have been hilarious - from "There is no fool like an old fool" all the way to " If only my wife would allow me.......".

Re: WC Weekend Accomplishments.....

#17

For those interested.  I called Hobart.

Gary Smyth

Their reply is to not touch it - open valve or not. Too dangerous unless the tank was filled with a compressed gas like Oxygen, Carbon Dioxide, or any inert gas like Argon. Otherwise it could be a bomb if treated poorly. Thanks guys.