Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Fusion or WW2???

Posts

Fusion or WW2???

#1

Fusion or WW2???

Dale Penkala

Just looking to see what all of you think about these 2 blades. Seems to be kinda mixed on all the reviews, although WW2 seems to be getting a bit more votes.

I'm putting it on a Grizzly cabinet saw 3hp model 690 table saw. Honestly I've always just used the normal blades you get at home depot, lowes etc... Figured since I got myself a better saw than what I had in the past it deserves a better blade.

I cut everything from BB plywood to zebra wood.

Any & all opinions are appreciated!

Thanks!

Dale

Mid-Michigan

Re: Fusion or WW2???

#2

Clint Searl

Re: Fusion or WW2???

Clint Searl

I've graduated from Forrest, Ridge, and custom 10" blades to Freud Fusion 8" thin kerf blades. They perform just as well or better, much less expensive, and disposable. With a team of horses behind them they'll cut through anything. Try 'em, you'll like 'em.

Clint

Re: Fusion or WW2???

#3

Re: Fusion or WW2???

Dale Penkala

Thanks for the info Clint! I've read that an undersized blade works well, but how is the blade/sharpness life last?

Thanks!

Dale

Re: Fusion or WW2???

#4

Re: Fusion or WW2???

Barry Irby

I have a WW2 and like it. Never used a Fusion so I can't actually answer your question. The only thing I don't like abut the WW2 is that it does not cut a flat bottom groove for splines ETC. With that minor exception I don't regret the cost, but then if I tried a Fusion I might.

Re: Fusion or WW2???

#5

Re: Fusion or WW2???

Dale Penkala

Thanks Barry for your input! I read these reviews on each blade and there great but there is always a few that have issues with each blade. I'm sure that these blades are not the PERFECT blade for every senerio but I'd guess they'd be better than anything I've had in the past. That is why I'm looking for all of the experience from the guys like you on this website.

Thanks again!

Dale

Re: Fusion or WW2???

#6

Clint Searl

Re: Fusion or WW2???

Clint Searl

My guess is that Freud's carbide is as good as Forrest's carbide, so I expect the same level of wear. Maybe the thinner blade puts less wear on the teeth.....don't know, but the Fusion glides through the wood. When it gets dull, I'll just replace it.

Clint

Re: Fusion or WW2???

#7

Re: Fusion or WW2???

Robin Corell in Atascadero CA

Rather than spending a lot of money on a single really good multi-purpose blade I would recomend buying a couple of dedicated single purpose blades. Buy a good rip blade and a good cross cut blade and you will get better quality cuts using the appropriate blade for each than by using a blade that has to make a compromise to do each type of cut. While you are at it go ahead and buy a bade with a tooth designed for clean cuts in venered sheet goods for cutting the BB ply.

If you are looking for premium perfoming blades stay away from the thin kerf designs. They were designed to alow underpowered saws to have greater cutting capacities. the amount of material you think you might save is miniscule and the cut quality on a thin kerf rip blade is not nearly as good as the quality of a .150 rip blade. if you have a 3 hp saw use it for what it can do and don't make compromises with the blades you put on it.

Lately I have been using Amana blades but I have also had good results with Everlast.

Robin

Re: Fusion or WW2???

#8

Re: Fusion or WW2???

Barry Irby

What does the Fusion cost? I'll have to try one. I like the idea of a blade that does the job and is not so expensive you have a heart attack if you wear it out or trash it.

OTOH, I do everything/whatever in my shop. One day I am building cabinets and another day cutting parts of a deck. I work in fits and starts. Sometimes I am in the shop for two or three days or it might be long enough to make one or two cuts. I am not in the habit of changing the table saw blade for a few cuts. I really like the fact that the Forrest blade does all of them well enough to leave it on the saw for all of them. I can rip a deck board and then Cut a tenon on some walnut for a table. It suits my style or lack there of. I suppose I need a good rip blade and a plywood blade but I just have not pulled the trigger. The Forrest blade is doing them well enough to avoid the cost and the time it takes to change blades.

Re: Fusion or WW2???

#9

Blade philosophy

Bill Tindall

I think many woodworkers are over concerned about smoothness of cut rather than cost and durability of the blade. Very few of the cuts I make with a table saw wind up showing and a combination blade makes these cuts just fine. And, I don't mind changing blades when needed. When the occasion arises where a utility combination blade is inadequate I install a more appropriate blade for the task. I just don't see wearing out a $100 blade doing utility work. To that end, the blade that stays on my saw is a 7 1/2 or 8" 40T combination blade (CMT, Freud, etc) that costs about $25. They have the significant advantage in that they don't get enough leverage on pieces of wood to throw stuff. Anything you have seen me post has been built with this kind of blade.

The smooth cutting blades, WWII for example, achieve this attribute by having a small side relief angle. This benefit comes with the cost of getting dull quicker.

Re: Fusion or WW2???

#10

Ellis Walentine

Relief angles and dulling

Ellis Walentine

Hi Bill,

Regarding your observation on carbide-tipped saw blades with low side relief angles (e.g., Forrest WWII) I was wondering if by "getting dull quicker" you were talking about the carbide edges actually breaking down sooner than they do on blades with greater side relief? I've observed that tips with low relief angles tend to accumulate pitch faster, resulting in more drag and burning in the kerf.

Any science on this?

Ellis

Re: Fusion or WW2???

#11

One Cure

Mark Mandell - Gone Round In Jersey

Easy-Off and an old tooth brush. That cleaned blade will cut like it was sharpened.

Re: Fusion or WW2???

#12

Re: Relief angles and dulling

Robin Corell in Atascadero CA

I was told by the guy that does my sharpening that the acid in pitch will actualy dull the cutting edge of the carbide. I don't know if this is one of those theoretical things or a real world thing.

Re: Fusion or WW2???

#13

Re: Fusion or WW2???

FredD

I agree 100 % with Robin's approach to saw blades.

In addition to getting the better blades configured for the cutting job ,they will do their best when you have the Rip Fence ,mitre slot and blade all running parallel with very littler run out ,which is not all always possible, but definitely something to work toward.

FredD

Re: Fusion or WW2???

#14

Re: One Cure

FredD

Amana Badles among others state in their literature hat Easy Off Oven Cleaner breaks down the Matrix holding the Carbide and is a no- no as far as they are concerned.

FredD

Re: Fusion or WW2???

#15

Heard That

Mark Mandell - Gone Round In Jersey

for years. Old debate. Last time it was the lye would attack the bronze brazing that held the carbide on the teeth.

Options:

a) Don't buy Amana carbide tools.

b) Regardless of whose tool it is, put the stuff on, scrub a bit, rinse off.

With the goop on there for all of 60 seconds, if it effects either the carbide of the brazing that quickly, you're holding a POS blade or bit and should probably trash it anyway as unsafe.

I regularly clean my Systi, Jesada, and Freud blades as well as every router bit I use. Some are over 15 years old and doing just fine.

Of course, if you choose to drop your tooling in a bucket of some corrosive and let it sit there for a week because you're too lazy to apply a bit of EG to the process, your mileage may vary, but then there's always the Darwin Award, eh? ;)

Re: Fusion or WW2???

#16

Re: Fusion or WW2???

Dale Penkala

Hello Barry

The Fusion costs $75-$80 on Amazon. The Forrest is $96 both with free shipping. I like the same idea to use one blade for most/all the work I do.

My boss uses the Freud combination blade and says that I'd be happy with it for the simple fact that all the other blades that I've used are barly middle of the road. He uses his for pretty much everything as well even though he has a number of specilty blades.

From what I gather from everything I read is both blades work well for everything but the Freud has the edge on ply wood less tear out and baby but smooth crosscuts. The WW2 is soposto have a better ripping up to 2" cuts vs a 1-1/2" rip cuts with the fusion. I have also read that the Fusion has the tendency to burn during ripping.

Thanks for the input!

Dale

Re: Fusion or WW2???

#17

Re: Blade philosophy

Dale Penkala

Hello Bill

Thank you for your input!

I read your article on this website several times and one of the things you brought up conserned me was the WW2 had the tendency to burn. Then I read this as being something that the Fusion did as well at times. Kinda why I posted here to get people that might have these blades and give me input based on there experience with these blades.

Thanks again!

Dale

Re: Fusion or WW2???

#18

Re: Relief angles and dulling

Bill Tindall

It was explained by the person at the saw shop (Misenheimer) but I have forgot the details. It did involve pitch build up I think. I was recently reading some papers on dulling and it is known that stuff in wood attacks the carbide binder when wood is machined (sawed too I suppose) That may be what is causing dulling.

Re: Fusion or WW2???

#19

It is true

Bill Tindall

Pitch is acidic, which is why it is readily removed/dissolved by basic cleaners like ammonia. I have recently seen many scientific papers on the corrosion of the binder in carbide tools by pitch and heat.

Re: Fusion or WW2???

#20

Re: Fusion or WW2???

Dale Penkala

Thanks Robin & Fred

Yes I had thought a little about doing that but honestly the idea of having one blade to do everything or close to it is just apealing to me thats all.

Thanks!

Dale

Re: Fusion or WW2???

#21

Re: Blade philosophy

Bill Tindall

Forest blades have a loyal following. You will not find many detractors among the owners. But for the sort of woodworking I do I would rather be dulling a blade that costs half or a third as much for routine work. When sharp they do yield exceptionally smooth cuts, but smoothness of cut is lower priority to me than blade life and blade cost.

Re: Fusion or WW2???

#22

Re: Blade philosophy

Phil

Not sure I can add much to what has already been covered, but I have both blades, and they are very similar in performance. I work primarily in cherry, and I might get slightly more burning with the WWII. They both end up with pitch build-up and I find that CMT Bit/Blade cleaner does a very good job of removing the pitch. Some folks like the ability to send the WWII back to Forrest for sharpening, so that's a point in favor of the Forrest blade.

Re: Fusion or WW2???

#23

6 of 1, half a dozen of the other........

Dave's Not Here

Both blades are top of line quality blades and either one will work just fine on your saw. I seriously doubt if one will perform any better than the other.

Re: Fusion or WW2???

#24

Re: Blade philosophy

Dale Penkala

Thanks Phil for the tip on the CMT cleaner! Yes to the WW2 resharpening option as well! At this point I'm leaning twards the Freud just because I have so many of there router bits. I guess if I'm not happy with it I'll give the Forrest a try. Still havn't pulled the trigger yet but when I do I'll give my opinion what little its worth.

Personal thanks goes out to everyone that offered there opinions & experiences with both blades as well as others.

Thanks!

Dale

Re: Fusion or WW2???

#25

Re: One Cure -- Formula 409

AZ in Colorado Springs

I use formula 409 and a toothbrush. It works well. I got some "blade cleaner" and when that was used up, I re-filled the bottle with formula 409.