Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Almost didn't stop in time....

Posts

Almost didn't stop in time....

#1

JL

Almost didn't stop in time....

JL

I had the glue brush in hand. I then thought - can I get this out of my shop??

I went and measured the door. I would have been about 3-4" shy of enough wiggle room to get this out of my shop.

Sigh - now I'll have to clear enough space in the HOT garage and assemble the piece up there. I REALLY don't want to work in the garage until the heat breaks.

Re: Almost didn't stop in time....

#2

BTDT

Mark Mandell - Gone Round In Jersey

Made the bed; glued rock solid. Went through the shop door just fine. Went through the rest of the house just fine. Got to the kid's bedroom door and I had a choice: Use the chain saw to either enlarge the wall opening or reduce the bed, finished with loving care, to component parts.

Congrats on your foresight being better than mine. :D

Re: Almost didn't stop in time....

#3

Re: BTDT

George Colonel's Workshop-Havertown PA

Good Afternoon Mark,

I never adoored chain saws either.

George

Re: Almost didn't stop in time....

#4

WHEW !

steve mackay

Re: Almost didn't stop in time....

#5

Re: BTDT

Bill Houghton, Sebastopol, CA

I take it Aretha's "Chain, Chain, Chain" is not one of your favorite songs, then.

Re: Almost didn't stop in time....

#6

Ya ain't alone...

Bruce, a MN Galoot

A bunch of years ago, I made a bookcase, nothing special, but it was to be one piece. Six feet tall and wide, one foot deep.

Inside the house, easy peasy, down the stairs, no sweat. It was two inches short of being able to make it under the header at the bottom of the stairs, and no amount of twisting or turning was going to make it happen.

The air inside the house turned blue. I had to cut it in half, make a new face frame and new ends.

Re: Almost didn't stop in time....

#7

I wouldn't

Mark Mandell - Gone Round In Jersey

go to the wall for them either, George, but it won't bar me from getting teeth into a problem either.

[ :D Bzzzzt, your turn! ]

Re: Almost didn't stop in time....

#8

Re: I Should Have Stihled Myself For That Reply

George@Colonel's Workshop-Havertown PA

Re: Almost didn't stop in time....

#9

It happens to the best

Bill Tindall

I was in a shop in VA and noticed the door was a mess, odd for a shop of considerable merit. Seems they made a table for President Bush and failed to do what you did-measure the door. Well it didn't fit out the door. So the door jam, and other alterations, had to be removed.

Re: Almost didn't stop in time....

#10

13 Minutes?

Mark Mandell - Gone Round In Jersey

That's approaching Husky speeds.

Re: Almost didn't stop in time....

#11

Appears There's A Market

Mark Mandell - Gone Round In Jersey

For some T-shirts here . . . . :D

Re: Almost didn't stop in time....

#12

Moses Yoder

Re: It happens to the best

Moses Yoder

Our salespeople are responsible for measuring the house, and they should be for what they get paid. One of our salespeople, and a good one too, just designed a 10 foot long vanity to go down a hallway and turn into a bath. Yep, that one got cut in half too. That salesperson is pretty arrogant though so I always laugh secretly when he makes a major blunder like that.

Re: Almost didn't stop in time....

#13

Re: It happens to the best

Barry Irby

A friend and I worked our way through college making cabinets. He is still making them for a living 40 years later. HE KNOWS exactly how long a wall cabinet can be and you can still get the shelves into it. The longer it is, the less like you can install the shelves later. You have to build them in if it has face frames. I don't keep the number in my head, Knowing the problem exists is the important part, I just call him.

Bought a house at foreclosure and my son and I remodel it. His new wife had her furniture in storage. Turns out the sofa would not go into the living room. We finally took the door jamb out, installed the sofa and then reinstalled the door jamb. Actually had to cut the opening out so tall that we had to make a sheetrock repair when the jamb was put back. the sofa will just stay with the house. Had to disassemble the refrigerator to get it into the kitchen.

UPS couldn't deliver a ten foot vanity into most bathrooms and neither could FEDEX. I would never try that.

I have a garage door on my shop, but the shop is so small this is almost never an issue. If I can assemble it in the shop, getting out or into almost any other place is not a problem. This might be the first advantage to a a small shop that I have thought of.

Re: Almost didn't stop in time....

#14

Re: It happens to the best

Larry in NW OHIO

Moses I can`t believe the colonel didn` t catch this one. But the next time that salesman has a 10 foot vanity and turns it into a bathroom I want to be there. :D Larry

Re: Almost didn't stop in time....

#15

From what Moses says,

Bill Houghton, Sebastopol, CA

that salesman's got plenty of vanity already.

Your shop should have made it this way:


img

Re: Almost didn't stop in time....

#16

I get seven minutes, and I agree

Bill Houghton, Sebastopol, CA

The Col. is a real sparkplug. Definitely our best, bar none.

Re: Almost didn't stop in time....

#17

Train, Train, Traaaaain . . .

Mark Mandell - Gone Round In Jersey

Re: Almost didn't stop in time....

#18

Re: It happens to the best

FredD

Moses , it should have occurred to the person building the Cabinet long before he started, that would never happen in a standard residential hallway.

FredD

Re: Almost didn't stop in time....

#19

Re: It happens to the best

FredD

You lost me there Barry, the length of a wall cabinet does not dictate whether or not you fix the shelves permanently in the shop or do as I do and make the shelves adjustable and put them in after the cabinet is installed. A lot easier that way on your back and the Cabinet.

Face Frame cabinets with dividers and stile dividing the space between can only be a problem if your not paying attention and that only rarely.

FredD

Re: Almost didn't stop in time....

#20

You are Right....

Barry Irby

I think there has to be a face frame and intermediate stiles (verticals) for this to happen. Lets say he cabinet is over 6' long and there are three pairs of doors, but no internal dividers, so the shelves are close to 6' also. The adjustable shelves won't go into the cabinets after the fronts are on because the diagonal is nearly the same as the length of the shelves. The longer the cabinet, the less difference there is between the length and the diagonal.

I'll have to ask my friend and get the details.

Re: Almost didn't stop in time....

#21

Moses Yoder

Re: It happens to the best

Moses Yoder

I think the longest cabients we build are a little over 12 feet. The person building the cabinets, and even I who do the engineering, never see the house or the plans for the house. The people who do the design wok and selling are supposed to make sure the cabinets will go in the house. We have taken cabinets through windows on the 2nd story.

We build 6 foot tall upper cabinets all the time,for 10' or 12' ceilings. One time a salesperson ordered 70" tall upper cabinets, so that's what we built. It turns out the salesperson had never shown the drawings with 70" uppers to the client. Then the owner of the business chewed out me and the guys in the shop who built the cabinets, saying we should have known nobody wants 70" upper cabinets, upper cabinets are always about 30" tall. It just revealed the fact that he knew absolutely nothing about the high end kitchen cabinet industry and was totally ignorant of the business he was supposed to be running. I went home 15 pounds lighter with my butt chewed off, laughing off what would have been my butt at the boss's ignorance.

Re: Almost didn't stop in time....

#22

Moses Yoder

Re: It happens to the best

Moses Yoder

Yea, for stock cabinets like you would buy at Home Depot that would never be a problem because they don't build cabinets that long. If you are building custom cabients to fit the space, with no vertical dividers behind the mullions, it can be a problem. We just put the shelves in before we staple on the back.

Re: Almost didn't stop in time....

#23

Re: You are Right....

FredD

Again Barry the length of the cabinet you describe is not relevant to whether the shelf will go in or not .

The shelf in that particular case will not go in because you have door openings of a foot or less. Unless the shelf was rubber , that is obviously a no go.

It relates exactly to why the ten foot vanity would not make the turn into a bedroom from a 36 " hallway.

So you may blame the design or lack of in both cases.

BTW how many Cabinets have you made with six foot long shelves ,apparently unsupported?

FredD

Re: Almost didn't stop in time....

#24

Moses Yoder

Re: You are Right....

Moses Yoder

When we build long uppers with no vertical partitions behind the mullions, we drill peg holes into the mullions and also into a back mullion that goes in the back. The hutch in the example is about 5 feet wide with 3/8" thick glass shelves with no vertical dividers behind the mullions. The back mullions and frame mullions have holes for shelf pegs, allowing us to put a short shelf in the top to fill the arched area.