Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

sharpening small drill bits

Posts

sharpening small drill bits

#1

sharpening small drill bits

Carol Reed, Strawberry, AZ

My jar of dull drill bits runneth over. I mean those less than 1/4" in diameter.

I do have an old Drill Doctor, currently in the Witness Protection Program, as it is no where to be found! However, that said, those small bits groove the sharpening stone terribly. And thus do a lousy job.

I also have one of those jigs that holds a bit to the side of a grinder wheel. I have great difficulty seeing that the bit is properly aligned. Also, the grinding wheels are sufficiently shrouded that this is an awkward solution.

So! Suggestions? Not adverse to buying more bits, but that was my solution for years. Now I have enough bits to practice sharpening them with no regrets if I screw a few of them up.

Thinking of building something. Google returned several clever solutions if only I was a machinist!

If I made a round plate with silicon carbide sandpaper glued to it, mounted on a motor (what RPM?), and used the drill bit jig under very good light and magnification...

Your thoughts and ideas are appreciated.

Re: sharpening small drill bits

#2

Jesper, Denmark

Re: Shortcut........

Jesper, Denmark

Small twist drills are so cheap that they are not worth sharpening. Buy them in boxes/tubes/packs of 10 or more - they take up no more room than all the dull ones you cannot sharpen effectively.

As you get older, the smallest drill you can actually see well enough to sharpen increases.

I think I'm a 3/8" and above at the moment.

Re: sharpening small drill bits

#3

Re: sharpening small drill bits

George Colonel's Workshop-Havertown PA

Good Afternoon Carol,

My Drill Doctor can sharpen under 1/4" drill bits, but its a "bit" of a hassle. I noticed on my last trip to HF, they were selling under 1/4" bits in packages of 10 from 1/16 thru 1/8, the sizes I break too often. Cost of a package of 10 is around $3.50. My packages are not marked by price, so I am trying to exercise my 72 year old memory. It occurred to me that I could buy 10 HF bits for about the same price as a package of two from the box store. I can't say that HF is selling every size in packages of 10. What they are selling seems geared to my needs as a bit breaking bad boy.

George

Re: sharpening small drill bits

#4

Re: sharpening small drill bits

Carol Reed, Strawberry, AZ

Thanks, George, but these are bits primarily used in metal. Sadly, the HF bits were good for maybe one hole before they were too dull to drill butter. I used brad points in wood.

Re: sharpening small drill bits

#5

Re: Shortcut........

Carol Reed, Strawberry, AZ

Right now I have more time than money. (Wonder when that was not true?) I do so relate to the not under 3/8" issue, though. I just got new glasses, so I was hoping to see the 1/4" to 3/8" better! LOL!

Re: sharpening small drill bits

#6

Re: sharpening small drill bits

Barry Irby

Carol, I was lucky enough to take one year of High School shop under a master shop teacher. He made us do an endless number of dull tedious chores, one of which was sharpening twist drills. That was forty some years ago and I can still walk up to my grinder and sharpen twist drills with little or no thought. They may not be perfect and a machinist might scoff but I get them a lot sharper than they were before and it only takes seconds.

Take a larger drill, say 1/2" or maybe 3/8 and put it on the rest on your grinder on which ever stone is finer. (grinder off at this point, you are just looking.) Orient the bit so that one cutting edge is horizontal and looking up. With the shaft rotated to the left, bring the full cutting edge into contact with the wheel. The angle on the cutting edge is usually about 60 degrees, so the drill should be about 30 degrees to the left of a line parallel to the side of the wheel. Now rotate the bit clockwise about 170 degrees while turning the bit slightly more to the left, probably close to 10 or 15 more degrees. Not sure it matters a lot what the angle of the rest is. You could draw a line on the rest parallel to the bit when you find the angle. Once you do the first flute/edge, rotate the bit and do the second one. very light pressure on the wheel and very small amount of metal removed. Keep the two flutes balanced. Look straight on at the business end of the bit and assure yourself the center is centered.

The idea is that the cutting edge has some relief behind it so that it will cut and chisel the wood/metal out of the way. That's why you increase the swing angle as you go. Take a large bit and try it with the grinder off and watch what you have to do to keep the bit in contact with the wheel as you rotate it. Ruin a few and you will get better and better.

I could have sharpened all my dull bits faster than It took me to type this.

Re: sharpening small drill bits

#7

Something different here....

Bill Tindall

My drill doctor uses a diamond coated steel wheel for grinding. There is no way for it to become grooved. Sharpening small bits it will last forever.

What are you doing to dull so many bits? I have a set I bought in 1966 and just got around to sharpening them.

Re: sharpening small drill bits

#8

Re: Something different here....

Carol Reed, Strawberry, AZ

I had plenty of dull ones in the jar to begin. Lately I have been drilling a ton of metal and cast iron.

As I said, my Drill Doctor is among the missing. A new one with the diamond wheel is way out of the budget.

Re: sharpening small drill bits

#9

Re: sharpening small drill bits

Carol Reed, Strawberry, AZ

They wouldn't let me take high school shop 50 years ago, Barry. So this is out of my skill set. Maybe with 1/2" drill bits or bigger I might be able to see what I am doing. With less than 1/4", no way, Jose!

Re: sharpening small drill bits

#10

Re: sharpening small drill bits

Bill Tindall

this is a woodworking Forum....didn't know you were drilling metal! Indeed such rogue activity will dull bits. And worse, if they aren't resharpened right they don't cut well (now how do I know that tidbit?) In the machine shop I used to hang out in, when I could, they sharpened the larger bits free hand and tossed the small ones, I suppose because they were harder to sharpen. I never got the hang of hand sharpening. The Drill Doctor makes it easy and I don't see any opportunity for grooving the diamond wheel. Maybe you can get a used on on Ebay.

Re: sharpening small drill bits

#11

Clint Searl

Drill bits are consumables

Clint Searl

Sharpening is a negative ROI.

Clint

Re: sharpening small drill bits

#12

Re: sharpening small drill bits

Ron Jones

Check this out on Amazon:

General Tools 16ME Multi Use Rule and Gage

It's less than $11 and will help get the angle on the point to be correct. There is a scale on the angled part of the gauge that helps center the point of the drill. There is a review on Amazon that is somewhat negative, but the reviewer did not address the sharpening function. Please contact me via email if you have questions or concerns.

Re: sharpening small drill bits

#13

Re: sharpening small drill bits

Barry Irby

I suppose this is the "eye hand coordination" thing, but I am not aware of really seeing what is going on. the process is so repetitious it is not really necessary to watch too closely. OTOH my son loses or miss lays so many small bits I get to buy lots of new ones. That's how he sharpens them.

Re: sharpening small drill bits

#14

Re: sharpening small drill bits

Robin Corell in Atascadero CA

I have always sharpened all my drill bits freehand and can get bits down to 1/8" reasonable sharp without too much trouble. but for smaller bits this jig works.

First you need to break down what you want to do which is to put two compound anges on the end of the bit, kind of like cutting crown moulding.

take a short length of hardwood, something similar in size to a 2x4, and cut it inhalf length wise and then join the two halves at one end with a hinge. This will function as a clamp to hold the drill bits as they are sharpend. close the clamp and drill a series of different sized holes along the seam while the board is clamped together. These holes should be drilled at 30* from plumb, which is the angle we want on the end of the bit. Next scribe a line through the center of each hole at 15* measured from the axis of the seam of the clamp. This line will be used to line up the point on the edge of the bit when it is placed in the clamp or,rather to create the compounded angle part of the cutting edge.

To use place the bit in the clamp protruding very slightly above the top of the board when it is clamped in a vise. Run a diamond stone across the top a couple of times and unclamp enough to trun the bit 180* and repeat for the other half of the bit.

Hope this helps you

Robin