Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

cleaning up a sliding dovetail

Posts

cleaning up a sliding dovetail

#1

cleaning up a sliding dovetail

mike

Sliding dovetail question: I use a router and router table to cut the joints but I like to make the male dovetail a little fat and then hand plane the dovetail down to insure a good tight fit into the the female. I need to purchase a new dovetail hand plane. I know Ulmia used to make one but any others? Lie-Nielsen?

thanks

Mike

Re: cleaning up a sliding dovetail

#3

There are other ways to skin this cat

Bill Tindall

Seems a needless expense to my frugal philosophy. I fit these joints apparently backwards from your approach. I make the male part and fit the female part to it. Fitting can be as easy as "bumping" the router over a bit and taking another pass. For hand made joints, my usual approach, I pare the dovetail shape by expanding a dado. The paring is aided by an angled block that matches the angle of the dovetail and a very sharp wide chisel. The chisel angle is indexed off the angled block. If the joint is too tight I bump the guide block over and take another shaving.

This joint has a huge gluing surface and it is not necessary to get it as tight as a smaller joint with less bearing surface.

Re: cleaning up a sliding dovetail

#4

and yet another approach.....

Bill Tindall

I have come to use "half tails" for this application. This joint is so strong that one can not convincingly argue that a half tail is not strong enough. Then fitting is a simple matter of planing off a shaving or two from the flat side of the male part. Again no specialized plane is necessary.

Re: cleaning up a sliding dovetail

#5

Why buy when you can make?

Neal in San Jose

I used an old wooden 1 inch rabbet plane. It probably didn't take an hour to bevel the bottom to the appropriate angle, grind the blade to the new angle and sharpen it. Old rabbet planes are available and cheap and they are so common you needn't feel guilty about modifying one. It won't have a depth stop or fence, but I've never missed those features.

Mine started life with an angled blade, but I don't see any reason one with a straight blade wouldn't work nearly as well. The biggest advantage of the angled blade is that it tends to pull the plane into the cut.

Re: cleaning up a sliding dovetail

#6

OR

Bruce, a MN Galoot

you can stick the router in a router table and scare off a little bit from the male part of the dovetail anyway. Trial fits on scrap are a snap, too.

BTDT a whole bunch of times.

Re: cleaning up a sliding dovetail

#7

Re: OR

Barry Irby

I cut them on a router table (homemade rig built into the wing of my TS) I cut the female part first. Then cut the male part so that the piece runs between the fence and the bit. I sneak up on the final cut on a scrap which I purposefully make while preparing the stock. When I get really close, instead of trying to move the fence I put a piece of tape on the work and take another pass. Sometime I put two thickness of tape on the lead end and one on the rear and that gives the piece a very slight taper and makes it easier to drive (gently) home. If I get heavy handed and cut away too much by a very small amount (I NEVER make big mistakes :) ) I glue them with epoxy to fill the void.

Re: cleaning up a sliding dovetail

#8

Re: OR

Bruce, a MN Galoot

and I thought I invented the tape idea. It works really well.

One nice benefit of using the router table for both cuts, if you can, is that you don't have to fiddle with adjusting the height of the bit.

Re: cleaning up a sliding dovetail

#9

Re: cleaning up a sliding dovetail *LINK*

del schisler

here is a video on the sliding dovetale. I havent watched it.


http://www.youtube.com/watch?v=aVk_qHJaRL4

Re: cleaning up a sliding dovetail

#10

Re: cleaning up a sliding dovetail

Lee Brubaker

A horizontal router table makes sliding dovetails quick & easy mainly because the female part of the joint can be an infatismal amount. My table uses two adjustment screws 16 threads to the inch hence making the adjustment using only one screw = 1/32 for a full turn, 1/64" for a half turn, & 1/128 " for a 1/4 turn. The longest sliding dovetail that I have made so far is 4 ft. & used as table breadboard ends. The joint is merely pinned in the middle from the underside of the table. Works for me.

Lee