Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

OT - steering wheel removal

Posts

OT - steering wheel removal

#1

OT - steering wheel removal

Carol Reed, Strawberry, AZ

I have a middle '80's John Deer garden tractor with a broken steering wheel. I bought a new steering wheel, but the old one is resisting every attempt to get it off. I have the parts and owner's manual. I removed the cross bolt.

Soaked in PB Blaster literally for weeks. Removed the plastic to get to metal. Used a three point gear puller with a breaker bar. I stopped at trying a pneumatic impact wrench. I have not heated the area - lots of plastic around that cannot be removed - like the dash.

There does not appear to be a spline, either in the drawings or in the new steering wheel.

Any thoughts, including cutting it off with an acetylene torch? I guess I could make some sort of heat shield. My brother has the welding gear, so I will have to load it up and take it over there.

One guy told me he had the same problem and wound up replacing the entire shaft. However, replacing a shaft that old could be problematic.

I guess we could cut if off horizontally and then weld an extension back on to hold the new wheel.

I am open to new ideas.

Re: OT - steering wheel removal

#2

Re: OT - steering wheel removal

Galen Vetterick

Since you have the new I assume it is not threaded and just a plain round shaft with the bolt as a pin. You say it is not splined so you might then try two good size pipe wrenches and try to twist it enough to break it free of any rust bond. Cheater bars allows made from pipe that will slip over the pipe wrench handles.

Re: OT - steering wheel removal

#3

Re: OT - steering wheel removal

Carol Reed, Strawberry, AZ

Thanks, Galen. Had not thought of that. I will have to check to see if there is enough room under the wheel to get a grip with a pipe wrench. Also that is a hollow shaft, so it might crush. But worth looking into.

Re: OT - steering wheel removal

#4

Re: OT - steering wheel removal

Dave Paine

I think that if you have a Dremel like tool (not the actual Dremel) you may be able to grind a slit in the old steering wheel, and then use e.g., a chisel to force the old wheel free of the shaft. You may need some wide grinding disks. I purchased some at a WW show. One of the vendors who sells many such items.

I purchased a tiller for my tractor, PTO driven, and did the first lift without checking lengths. The PTO was too long and pushed the tractor end of the PTO towards the engine. I could not release the PTO. I ended up grinding the PTO with a Dremel like tool and used a chisel to free this puppy. I then had to replace the universal joint, but at least the PTO was removed from the tractor.

If I seem to not like Dremel brand, it is not a co-incidence. I happen to have a Dremel brand tool gathering dust. It works fine as long as it does not have to work against anything harder than air.

Re: OT - steering wheel removal

#5

Re: OT - steering wheel removal

Carol Reed, Strawberry, AZ

Wow! An excuse for a new tool! Kewel!!

What do you suggest other than the Dremel?

Re: OT - steering wheel removal

#6

Dale Lenz

Re: OT - steering wheel removal

Dale Lenz

Call a John Deere dealer with a repair shop/ purchase the shop manual for that tractor. You might need a new tool, but not a woodworking one, sorry.

Re: OT - steering wheel removal

#7

Re: OT - steering wheel removal

FredD

It's a two person job Carol, if like Galen says ,you can get two wrenches on the nut and shaft, have a second party tap the nut or shaft end as you apply pressure , it has worked for me on really stubborn pipe fittings.

FredD

Re: OT - steering wheel removal

#8

If you have a compressor get a cut off tool

Phil Joines

from Harbor Freight. Usually $29.

Re: OT - steering wheel removal

#9

Re: OT - steering wheel removal

Carol Reed, Strawberry, AZ

No nut. Its pressed on.

Re: OT - steering wheel removal

#10

Re: If you have a compressor get a cut off tool

Carol Reed, Strawberry, AZ

Thanks, Phil. Good idea. Maybe my brother already has one.

Re: OT - steering wheel removal

#11

Re: OT - steering wheel removal

Carol Reed, Strawberry, AZ

Have the books - see original post.

My shop has far more than woodworking tools. So new non-woodworking tools are A-OK with me! LOL!

Re: OT - steering wheel removal

#12

Dale Lenz

Re: OT - steering wheel removal

Dale Lenz

If the owner's manual tell you how to remove the steering wheel, great! In years past I've always purchase the Shop Manual for my equipment, mainly cars.

Re: OT - steering wheel removal

#13

Re: OT - steering wheel removal

FredD

Well I gave it a shot

FreDD

Re: OT - steering wheel removal

#14

Re: OT - steering wheel removal

Galen Vetterick

If the steering wheel hub is open put a bolt or solid shaft inside the hollow shaft to back it up if you can so you do not crush it.

If the hollow shaft has worked on the through bolt and elongated the hole smearing metal into the hub. You might try drilling the steering wheel hub only with a larger bit to break it loose. You may not have room to do this drilling I don't know.

Re: OT - steering wheel removal

#15

Re: If you have a compressor get a cut off tool

Galen Vetterick

If you do not have an air or electric cut off saw or no room than do you have a sawzall as I would think that would fit down between the wheel spokes to split the hub legthwise.

Re: OT - steering wheel removal

#16

Re: OT - steering wheel removal

Thomas S Stockton

Post your question on www.tractorbynet.com under the john deere section someone has probably had the same problem before.

Tom

Re: OT - steering wheel removal

#17

Re: OT - steering wheel removal

Larry in NW OHIO

Carol As said before, I think your best bet is to cut the hub length ways a couple of times. once on one side and directly across from it again. If that doesn`t do it cut it again somewhere. We did this a couple of time when I worked maintainence. They were a couple a very stubborn pulleys. If you do it this way, you`ll do the less damage to your shaft. Best of luck. Larry

Re: OT - steering wheel removal

#18

Moses Yoder

Re: Oxy-Acetylene torch

Moses Yoder

I have no experience with John Deeres specifically, but I have quite a bit of experience with the O-A torch. I assume the wheel is plastic on a steel shaft, which would be pretty easy I think to cut the wheel off without damaging the shaft. An Oxy-Acetylene cutting torch would make short work of melting through the plastic I think. You would want to cover whatever is underneath with an old cloth because the plastic will drip down, and it will also be smelly. The wheel was probably pressed onto the shaft with a 5 ton hydraulic press and the bolt just added as a safety precaution.

Re: OT - steering wheel removal

#19

Re: OT - steering wheel removal

Al Stokka - Cambridge, Iowa

Carol,

A procedure which works on 1940's-50's Ford tractors:

Use two hammers, both heavier than 16 oz.

Position the heavier (or equal) weight hammer against the side of the steering wheel hub. Use the other hammer to whack (technical steering wheel removers term) the steering wheel hub on the side opposite the first hammer. Work the hammers all the way around the hub until you have whacked the entire circumference. Now try removing the steering wheel by grasping opposite sides and wiggling the wheel, first one dide , then the other. You can also attach the wheel puller before wiggling the wheel. If the wheel doesn't gudge, repeat the two-hammer whacking.

Al

Re: OT - steering wheel removal

#20

Kneale Brownson

Most of those wheels have a metal liner

Kneale Brownson

that corrosion-welds onto the shaft.

My approach would be to cut parallel with the shaft using a hacksaw so I DIDN'T CUT INTO THE HOLLOW SHAFT. Probably a couple cuts.