Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Router with Swivel Cap ?

Posts

Router with Swivel Cap ?

#1

Router with Swivel Cap ?

Yonak

One job I do is to rout panels (slightly smaller than a typical table top), which involves pushing the router all the way around the edge (cord hanging from the ceiling), turning it over and doing the same thing to the other side, putting that panel in a stack, replacing it with another one and doing it all again for 50 panels. After about 7 or 8 revolutions the router cord gets twisted and makes it less maneuverable, not to mention shorter. I now do sort of a pirouette, holding the router over my head, after each routing revolution to keep the cord straight. See, I can't look at the computer screen and listen to music at the same time without getting confused so you can imagine how this pirouette shakes me up.

When the woodworking show was in Atlanta I asked all the router manufacturers if there was such an item as a router with a turret top which swivel would keep the cord untangled. They all said, "No," but they would present the idea to their design department. Well, I figure that's the last thing on these salesmen's agendas so I thought I'd ask this august group if anyone has any ideas for a solution.

Re: Router with Swivel Cap ?

#3

Re: Router with Swivel Cap ?

Ken Oakley-Sunny St. Cloud, Fla

Would it be practical to put the panel on some type of turntable, thereby allowing you to rotate the panel and keep the router more or less stationary. An overhead pin router would do the job great.

Re: Router with Swivel Cap ?

#4

Re: Router with Swivel Cap ?

Jesse Cloud

Make a fixture you can attach to the ceiling (or at least a few feet above your bench) onto which you can attach the power cord and vac hose if you are using dust control (and I hope you are). This way the cord and hose will always be out of your way.

Re: Router with Swivel Cap ?

#5

Re: Router with Swivel Cap ?

Yonak

Jesse, it would be a good idea if the dust port was also somehow in the top so it could swivel with the cord.

Re: Router with Swivel Cap ?

#6

Swiveling outlet instead?

Bill Houghton, Sebastopol, CA

I have this vague feeling that I've seen, somewhere, outlets that will swivel.

Re: Router with Swivel Cap ?

#7

Re: Router with Swivel Cap ?

Dave Peebles Lyons, Ohio

Hi Yonak,

This may seem crazy, but... have you considered making a table with a small low rpm motor that rotates the pieces you are routing? Maybe with a vacuum system to hold the pieces.

See, I told you it was crazy. :)

Good luck,

Dave

Re: Router with Swivel Cap ?

#8

Here is one way that will work

del schisler

Something else you can do to reduce the twist up is to hang an extension cord from above your work table and plug into this. The cord will still twist but it wont try and fold back on itself like it would just running off to the side. Of course there is always the battery operated PC router, no cord period.

Re: Router with Swivel Cap ?

#9

Re: Here is one way that will work

Larry in NW OHIO

Along with Del`s suggestion with hanging the cord from the ceiling. Maybe before you begin take the cord and twist it in the opposite direction, that way your kind of ahead of the twist, pun intended, sort of. Also that way after afew boards you can just unplug it and untwist it or maybe the coard hanging fron the ceiling will untwist itself. Good luck with your project. Larry

Re: Router with Swivel Cap ?

#10

Re: Here is one way that will work

Larry in NW OHIO

I happen to think, very dangerous when I do that, last nightthat maybe you could somehoe use a vaccum hose off of a house canister vaccum that swivels 360 degrees. Our Kenmore does that and thought that could be rigged somehoe to your router. Hang it on the ceiling and run the power through it somehow. It would take some thinking but I believe it could be done. If you are doing more of this work, it may be worth looking into something like this. I also Googgled rotating joints and came upon a few places that make some, but were very expensive. But if I had more time a person might find something for at home. GOOD LUCK and let us know if you come up with something. Larry

Re: Router with Swivel Cap ?

#11

Amperage rating

Bill Houghton, Sebastopol, CA

I don't know what vacuum cleaners draw, but you would want to check the amperage draw on the vacuum that you were cannibalizing and make sure that it's equal to/greater than the amps of the router in question - otherwise, you could melt/burn/let the smoke escape from the swivel connection.

Letting the smoke escape from electrical components is not only bad for them but can be bad for you.

Re: Router with Swivel Cap ?

#12

Re: Here is one way that will work

Yonak

Thanks Larry, and everyone. I'm just not really following you how running the power cord through a vacuum hose that swivels would keep the cord from twisting.

Regarding the rotating receptacle, it would have to turn from only the force of the twisting cord. Unless it's on ball bearings or something, I believe the cord would still twist. I can't reach the receptacle on the ceiling without a ladder to twist it by hand.

The rotating table seems interesting. It would have to have some kind of locking mechanism, possibly operated from a foot pedal, so it wouldn't turn while I was routing against the edge, otherwise the panel would keep running away from me as I rout. A motorized turn would provide a firm edge to rout against and would turn while I rout so I wouldn't have to stop routing to turn the table. I am a little concerned about trying to rout against a moving piece .. kind of like dancing on a moving dance floor.

..And now I have thought of a solution after reading all the suggestions. Between panels, when I set the router down, I can set it on a lazy Susan and spin the router one revolution in the opposite direction before I pick it up. I would still like to see a non-cord-twisting router, however, as I'm not sure how cumbersome the lazy Susan idea will be.

I appreciate everyone's thinking about this with me.

Re: Router with Swivel Cap ?

#13

Re: Here is one way that will work

Larry in NW OHIO

Yonak You have the idea, but the hose and cord are one. The power cord comes in from the canister and up into the hose connection so the cord is inside the hose and down to the handle where you would tap into the cord to your router. So as you go around the panel you pull the hose with the cord and it swivels at the hose connection at the end of the hose where the cord begins. Believe me the hose swivels very easy. As someone said the cord and connections would have to be big enough to carry the amps. If I were doing it I would try it just for the fun of it. There has to be some thing like that out there somewhere, but it would be expensive. I`m still going to look around, you have my interest going so I want to find something. Larry