Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

the Hits just keep on coming...OT

Posts

the Hits just keep on coming...OT

#1

the Hits just keep on coming...OT

Barry Irby

I have been posting about the house I bought at foreclosure to flip. This is the one that was FULL of junk. We have filled a 30 yard dumpster to overflowing and still have more.

Today we started tearing out the rotted sections of the floor. Going to have to replace eight joists. We knew this was coming because the tub had been leaking. Also found rot under the kitchen sink. No damage to the joists though. Then I removed a baseboard heater in the bathroom to allow for replacing the joists and floor. The wires were aluminum. As a Home Inspector I was surprised. The house was built in 1977. I have always thought that the aluminum wire era was the late 60's through the early 70's.

While working on the floor we discovered that someone had stolen the copper pipe under the floor. So now I need to replace that. No need to put copper back, they would just steal it again. Anybody got experience with CPVC?

Re: the Hits just keep on coming...OT

#2

Re: the Hits just keep on coming...OT

Steve Schoene

My new house was done with PEX. Lots of advantages, in particular a major reduction in the number of joints, since whole runs--say one to each bath and be made connecting only once to a supply manifold and a second time to the distributions to individual fixtures in a particular space. That means labor costs are less, the total system costs are less, even though PEX material is more expensive than the CPVC plumbing.

Re: the Hits just keep on coming...OT

#3

Re: the Hits just keep on coming...OT

Galen Vetterick

I agree the PEX may be easier to run if you cannot have clear acess to the runs. The clamping tool method is the cheapest method as only one tool needed for different pipe sizes. Crimping and expanding PEX methods are more expensive tools and fitting. Some local codes may not be updated to allow PEX.

If CPVC is allowed by local code there is nothing wrong with using it if you can get to all the fitting location and put in your runs. Code may require sch 40 or 80, so need to check. Use the proper primer-cleaner and solvent cement for the schedule use. Use no 40 cement on 80 pipe glue ups. Although some say universal the 80 solvent cement is more agressive.

Most are low VOC now so it take longer to get a high from working with it.

Since there is no industry standard to fitting dimensions (lay length) it helps to stay with one brand on makups. They make a lot of transiton fitting so you can reconnect to old or terminate with other types of pipe.

Sound like you have a lot of work to do on this house, good luck. Hope you make your money back in this economy.

Re: the Hits just keep on coming...OT

#4

Re: the Hits just keep on coming...OT

Terry Quiram

Another vote for PEX. Last year we gutted out kitchen and bath. I had replaced the copper a number of years ago with PVC. When we had PEX installed we went from 1/2 to 3/4 and what a difference that made. PEX is quick and easy.

Re: the Hits just keep on coming...OT

#5

Re: the Hits just keep on coming...OT

Scott Greaves

I like PEX. I have re-plumbed three houses with PEX now and have had no problems. It's a lot easier to run through where old pipe was taken out. I use the Wirsbo PEX with the expanded tool. The tool was pricey, but now I have it, and it makes very secure connections. The first place we did, it took me three days to cut the old pipe out with a recip saw. It took my Wife and I a half a day to re-plumb with PEX.

Scott.

Re: the Hits just keep on coming...OT

#6

A bit pricey?  My dealer quotes $700

Gary Smyth

for the Milwaukee expander. For all the good things about PEX that kind of money practically assures I better have a big house of more than one.

Re: the Hits just keep on coming...OT

#7

Buying Alternative

Mark Mandell - Gone Round In Jersey

1. Rip out the old pipe.

2. Run the PEX lines leaving extra at the ends of each run with the line pairs carefully labeled.

3. Pay a friendly plumber $500 to come in and make the connections.

Wasn't that easy?

Re: the Hits just keep on coming...OT

#8

Re: Buying Alternative

Gary Camp, Bend, Oregon

When we moved our house the plumber did all the "fixing" with Pex. He just used the Stainless band clamps. The soft drink industry has been using them for many years with out problems. The plumber soldered in threaded adaptors and hooked up the PEX just like the system had been run with copper.No home runs. I did go buy a crimping tool and assortment of band and fittings, partly becuase I had changes to make and partly because I like to be prepared. So far so good.

glc

Re: the Hits just keep on coming...OT

#9

Re: A bit pricey?  My dealer quotes $700

Scott Greaves

Mine is just a hand operated one, and it only ran me about $230 when I bought it. I forgot to mention that we also ran PEX for the radiant heat in my shop. Just like any good tool, if you use it, it pays you back over time.

Scott.

Re: the Hits just keep on coming...OT

#10

Re: the Hits just keep on coming...OT

Larry in NW OHIO

Barry I hope You`ll read this, since it took me this long to remember where I saw them. Go to Ebay, they have a bunch of them made by machinists at their homes. They seem fairly inexpensive. That is where I would go if I wanted one, at least I would look over them better. Good Luck with your house, and the nag next door. Larry

Re: the Hits just keep on coming...OT

#11

Re: the Hits just keep on coming...OT

Larry in NW OHIO

Barry I`m sorry I didn`t even say what you should be looking for. I was talking about PEX crimping tool and the rings. I`m having more and more BRAIN FARTS as the days go on. One of these days one of them are going to back up on me and I`ll be lighting a match or something and I`ll blow myself up, Larry