Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

How is this tool best sharpened and adjusted

Posts

How is this tool best sharpened and adjusted

#1

How is this tool best sharpened and adjusted

Bill Tindall



I have had this scraper for several years and never had a favorable experience with it. I have come to learn that unfavorable hand tool experiences have largely been a result of improper sharpening and I suspect this too is the case.

As is, the tool is grabby and I have too little control of what it is scraping-digs and chatters. I have come to learn that with a card scraper such performance is due to too much burr. But on this tool....?

The blade came beveled, about 45 degrees but I am unsure if a burr is also added to this bevel and what the best angle of grind should be.

Second, there is an adjustment screw that would flex the blade, analogous to flexing about one's thumbs for a card scraper, I suppose? This thumb screw adjusts depth of cut....?

Bottom line, what is proper sharpening and thumb screw adjustment to get good control of the shavings.

Re: How is this tool best sharpened and adjusted

#2

Moses Yoder

Re: How is this tool best sharpened and adjusted

Moses Yoder

That looks like a #80 cabinet scraper. I am not sure where the cord is to plug it in, or whether you have a 230 volt single phase motor or 208 volt 3 phase. It can work with a 45� bevel on the blade, and I would probably just leave it on for now but file it off as the blade is sharpened. The bevel would be turned back toward the screw, and you would push the scraper away from yourself normally to use it. It can also be pulled, but you don't get as much power on a pull stroke. The #80 is built for fast stock removal. I would make sure the bottom of the body is flat and smooth, wax it, and that is good enough. Some people polish them but I don't really think that is necessary. The scraper should be sharpened using normal scraper sharpening techniques which you could read about for a long time probably by doing a search here. The one thing with these is the burr should only be turned at a slight angle, 5� actually works pretty good. If it is turned at too much of an angle it doesn't bite into the wood. I find that a very small burr works best, and amateurs normally make the burr too big, resulting in rough cutting and a cut that is soon dulled. I use a carbide bit for turning the burr, works very well and was free.

Re: How is this tool best sharpened and adjusted

#3

Clint Searl

Re: How is this tool best sharpened and adjusted

Clint Searl

I keep mine to around the factory bevel, which looks about 45 degrees, and roll a pretty strong hook. It seems to work best if the blade is bowed with the screw and exposed no more than the thickness of a Bicycle playing card or business card.

Clint

Re: How is this tool best sharpened and adjusted

#4

Moses Yoder

Re: Forgot to mention

Moses Yoder

To set the blade, I put a sheet of paper on my bench, set the back edge of the scraper on the paper and the front edge on the bench, push the blade down to the bench and lock it in place.

Re: How is this tool best sharpened and adjusted

#5

Re: Forgot to mention

Larry in NW OHIO

Moses, I don`t thing that is the corded #80 scraper, I believe it`s the new and improved #85 battery operated they came up with a year later. ;) ;) Larry

Re: How is this tool best sharpened and adjusted

#6

Re: How is this tool best sharpened and adjusted

FredD

and works even better by having a slight curve to the blade.

FredD

Re: How is this tool best sharpened and adjusted

#7

JL

How I do it...

JL

Take the burr off with a piece of 320 grit sandpaper on a flat surface.

Make sure the bevel is flat and even (file, waterstone sandpaper or whatever).

Touch up the flat side a bit after the bevel work (400 grit sandpaper or waterstone).

Turn the burr with a couple of strokes of my burnisher.

Like Moses, I set the "depth" with a piece of paper. I adjust the depth of cut by using the thumb screw in the center.

Re: How is this tool best sharpened and adjusted

#8

thanks all,  it's doing better now

Bill Tindall

Re: How is this tool best sharpened and adjusted

#9

Ellis Walentine

Consider FredD's advice

Ellis Walentine

When you push on the center of the blade with the thumbscrew, it pushes the center deeper than the sides, so you can't take a nice, coplanar shaving. I used to file a slight reverse camber in the middle of the blade si ti would flatten out when the screw is advanced.

The 45� angle makes the edge weaker than that of a card scraper, so you should use lighter strokes with the burnisher than you may be used to. A lighter burr should have more strength and last a bit longer. This is partially dependent on the condition of the blade.

Ellis