Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Cutting arcs in stretchers

Posts

Cutting arcs in stretchers

#1

JL

Cutting arcs in stretchers

JL

I admit it, I'm not the neatest person with a band saw. I haven't bought a spindle sander (yet), so it is sometimes a challenge to clean up the inside curve of stretchers.

I've used a router trammel to cut circles before. I was figuring that I could adapt it somehow to cut arcs in stretchers. My other choice is to use a pattern bit in my router table. Any other thoughts??

TIA

Re: Cutting arcs in stretchers

#2

Re: Cutting arcs in stretchers

Bob Burnet (NW FL)

If you have a drill press, you can chuck up a sanding drum and "sand to the line" to clean up your less than smooth concave cuts. Rocker has sanding drums, others do a well.

Re: Cutting arcs in stretchers

#3

Moses Yoder

Re: Cutting arcs in stretchers

Moses Yoder

On that type of arc you are not talking about a really tight radius. Therefore a spokeshave is your best friend. The Lee Valley shave set for radius work is a really nice way to do this.

Re: Cutting arcs in stretchers

#4

Clint Searl

Drawknife

Clint Searl

Re: Cutting arcs in stretchers

#5

Hand tools

roger lance

Re: Cutting arcs in stretchers

#6

pattern bit or spoke shave

Bill Tindall

If I was making a reproduction it would (was and will be) be spoke shave. If I was in production mode it would be pattern routing. Look for a band sawing insight later tonight or tomorrow when I get a chance to post it. I am now suddenly able to just about split a line band sawing.

Re: Cutting arcs in stretchers

#7

agreed

Bill Tindall

I bought the set on an impulse (always risky action) but I have been delighted with them.

Re: Cutting arcs in stretchers

#8

Re: pattern bit or spoke shave

Jesse Cloud

Lots of ways to skin this cat.

If you have lots of space or can do it outdoors, its easy to make a trammel out of a long scrap, a screw for a pivot point and some screws to mount your router. But for a gentle curve, we are talking a lot of space...

I usually use a bending stick to draw a pleasing curve on a piece of 1/4 inch mdf. Mdf fairs really easily with a sanding block, though a spindle sander will speed things up. After its faired, you can double stick it to the workpiece, rough cut on the bandsaw and then finish with a pattern bit. I prefer handheld over router table - feel I have more control.

The template will let you make multiple stretchers with the same curve. After a while you accumulate enough templates that you probably have one that will work.

But on the other hand, fairing a curve with a well tuned spokeshave is about as pleasurable as it gets.

Re: Cutting arcs in stretchers

#9

Re: Cutting arcs in stretchers

Keith Newton----Little Rock, Arkansas

If you are only doing a few, I would not bother with a template or trying to use a router.

For slight inside curves, you can cut a double ended arc that you slip behind the platen of a hand held belt sander, which allows you to sand inside curves without bumping along on the rollers.

If the work is clamped in a vise, I find it pretty easy to spread my feet, and sort of rock along the arc, with my arms locked, and feel the bumps, until I have a fair curve. It is quick and easy.

Re: Cutting arcs in stretchers

#10

Re: Cutting arcs in stretchers

Barry Irby

I cut the last ones I did by drawing a curve with a spline or bending stick. After cutting the two stretchers with a band saw I clamped them together and faired them with a belt sander. Then I reversed them end for end and faired them again. This seemed to make them nearly identical and symmetrical. They were about five feet long, so the curves were gentle. OTOH I did the end rails the same way and they were less than three feet.

Re: Cutting arcs in stretchers

#11

Re: Cutting arcs in stretchers

paul in AZ

Thats how I do it. Bendy stick, bandsaw and belt sander. I just finished one with stretchers a bit over 4 1/2 feet that way. The deepest part of the arc was a bit over an inch.