Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Why don't more people spray finishes?

Posts

Re: Why don't more people spray finishes?

#26

Re: Fan Question

Dan Donaldson

It would not be official policy, but awhile ago someone (not on WC) tried to use a fan to get an explosion and was unable to do it. I would not be adverse to using a box fan with plastic blades. A furnace is a whole other game, with an open flame etc. (Same with a water heater.)

Re: Why don't more people spray finishes?

#27

Re: Agree with you on one point!

Dan Donaldson

Not sure about that ;) The last colonoscopy I had, I remember going into the room and then being in the car going home and nothing in between.

Re: Why don't more people spray finishes?

#28

David Barnett

Re: Agree with you on one point!

David Barnett

Just how well do you know your gastroenterologist, Dan?

Re: Why don't more people spray finishes?

#29

Re: Fan Question

Hank Knight

Thanks for the response, Dan. I don't think the fan blade is the concern; it's the sparks from the motor brushes. In any case, I don't think I'm going to chance it. I do a little spraying outside without a fan, as I mentioned, and I'm probably going to step it up a bit. I have a new pressure fed HVLP gun that works great. I just need to pick my days to avoid blowing leaves and trash in my finish.

Re: Why don't more people spray finishes?

#30

Re: Why don't more people spray finishes?

Greg Muller

For me the biggest obstical has been the lack of instruction on the subject of spraying. I purchased a cheap (49.99) HVLP sprayer from grizzley and have been trying to learn how to use it but the learning curve seems to be steep. I suspect some of the problem may be the quality of the sprayer. I have found that I can not get it adjusted properly and have produced an orange peel finish on everything I haved sprayed. I would love to be able to use a sprayer and get as good a finish as I can produce by hand at this point. If anyone knows of some good written material on HVLP spraying please let the rest of struggling newbies know. Also what would be recommand as a good HVLP sprayer under $100 dollars.

Re: Why don't more people spray finishes?

#31

Dale Lenz

Orange peel

Dale Lenz

There can be several reason for OP, bottom line: The lacquer is not leveling out before it sets up. I thin my lacquer (SW) about 40% and add a small amount of retarter. Look at the sprayed surface with a raking light and if surface appears smooth, it's usually going to dry smooth.

Re: Why don't more people spray finishes?

#32

Re: Fan Question

del schisler

it is a induction fan . I been using it for 8 yrs i guess. It has not had any problum or have i. I have a 12x24 with a 36" door which is open and lot's of air and also have 4 more 36" windown's which i don't open. I also have another 36" fan that is behind my delta leigh which take out the dust. All the spray goes out side Nothing inside the shop. I don't worry about a fire ect. Now if it was a close up place with no air than i would thank about it. But Their is no chance of anything going wrong on my end . And no dust. I use the air hose and clean my saw dust all the time . I guess you can eat off of any thing in the shop. I am very clean on every thing. I air off all my tool's after use so that they are like new when i get then next time. I have alway's been that way. my 2 cent's

Re: Why don't more people spray finishes?

#33

Cheep lacquer won't do it

del schisler

Most of the box store lacquer i woudn't use. or the lacquer thiner. I use only M.L.CAMPBELL sanding sealer and the simi gloss. And also the thiner is M.L.CAMPBEL also. Cost more but i have never had a bad finish. Now shermin william's stuff is just as good. go get some of that and i bet most of your porblum's will be over. The nozzel on the sprayer should be 2 mm . Also 30 lbs of air This is what you need. I thin my lacquer probly 10 5o 20 percent around their shuld be ok. If you get it to thin you will get run's bad. good luck del

Re: Why don't more people spray finishes?

#34

Re: Cheep lacquer won't do it

Greg Muller

I have only tried spraying water based poly. I have no clue how to spray lacquer or if the equipment I have would work.

Re: Why don't more people spray finishes?

#35

Jim DeLaney, Austintown, Ohio

Re: Why don't more people spray finishes?

Jim DeLaney, Austintown, Ohio

Lately, I've been spraying M.L. Campbell's water-based Pre-Cat lacquer, and I really like that stuff. Thinned about 20%, it goed through my little HVLP gun perfectly, and lays down a beautifully smooth coat. Dries in minutes, and builds very well. I've pretty much found the last finish I'll be needing, I think.

Oh yeah - it tints nicely with Transtint dyes, too.

Re: Why don't more people spray finishes?

#36

Dale Lenz

You waste more material spraying vs...

Dale Lenz

I'd say it's safe to say, I'd use 2 qts. or varnish thinned 33% for wiping vs. 5 gal. of spray lacquer, thinned 40%. So 30 bucks (+/-) vs. close to $200 for the 5 of lacquer and thinner for the same amount of coverage. Yes, spraying is quicker and that's why I use it. I spray at 10# of air or so, maybe less, put more coat of lacquer on vs. varnish.

Re: Why don't more people spray finishes?

#37

transfer efficiency 50 to 70%

Bill Tindall

The figures I have heard are that the transfer efficiency for convention spray is about 50% and a greater number for HVLP. I spray conventional and in my experience that 50% figure is about right as best I can estimate. The true value is certainly not greatly less.

Re: Why don't more people spray finishes?

#38

Equipment

Greg Muller

Does anyone use the Rockler HVLP spray system and if so how do you like it. It seems to get good reviews and for $139 it might be a good starting point for the beginner such as me.

Re: Why don't more people spray finishes?

#39

comment

Bill Tindall

HVLP is more difficult to learn, but one certainly can learn and do well. I tried it, didn't like it and went back to conventional. The cheapest and easiest way to learn is to buy an inexpensive air compressor and look for a professional conventional gun on Ebay. It's all about optimum atomization of the liquid. The better it gets atomized the easier it is to get a good result.

Re: Why don't more people spray finishes?

#40

Re: Equipment

Stuart Johnson

I have it and it works well and I did get a nice finish on some cabinet. I can't really comment on how well because I've never sprayed before. I did seem to use way more lacquer than I thought I would need plus the first couple coats were very rough feeling. That was probably caused by the user.

On the plus I had read about just leaving the lacquer in the cup when finished and not worrying about cleaning it. I tried it and four month later it sprayed just fine.

Re: Why don't more people spray finishes?

#41

Dale Lenz

Your lucky....

Dale Lenz

make a habit of leaving finishing material in your gun and it will come back and bite you, damn how I know. Experience is a good teacher!

Re: Why don't more people spray finishes?

#42

Re: Your lucky....

Stuart Johnson

I'm sure you are correct but my main reason for the purchase was the ability to just set it down and forget about it when done spraying. But, now you have me wondering if I left it with lacquer or thinner. When I went out and tried it I didn't spray anything I just plugged it in and sprayed out the door. I thought it should have taken a bit for the lacquer to melt what was left in the gun. I'm certainly going to check.

When I sprayed my cabinets I would run thinner through it after each coat. This really became a pain after a bit. Finishing or painting is my most dreaded tasks. It seems like you spend 10 minutes in prep and cleanup for every minute spent apply finish.