Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Ripfence for Sears/Craftsman Tablesaw

Posts

Re: Ripfence for Sears/Craftsman Tablesaw

#26

Re: Posting pictures (you need a profile)

Dale Penkala

Thank you Dan! I will do that. I was looking to do that but didn't quite get things right. I'll try to do that again.

Thanks!

Dale

Mid Michigan

Re: Ripfence for Sears/Craftsman Tablesaw

#27

Re: Posting pictures (you need a profile)

Dale Penkala

Ok I got my profile and lets see if I can post a pix.


Re: Ripfence for Sears/Craftsman Tablesaw

#28

Louie Lovas

Re: Rip Fence for Sears/Craftsman Table Saw

Louie Lovas

Been reading this thread and figured I would reply because I 'did' upgrade an old Craftsman TS, but I added a bit more that just the rip fence (Delta's Unifence). I also upgraded the motor (2HP, 220v) with the link belt/balance pulleys too. Lastly, I tossed those contractor legs and build a cabinet for the whole thing. This includes a right-mounted router table, dust collection bin and drawers for 'stuff'. You can see the contraption at this link: http://flinthillfurniture.com/thetablesaws.html

Of course if you look closely at the pics, you'll see a second table saw (also a old 1980's vintage) with a JessEm crosscut sliding table. This saw is also upgraded with a mobile cabinet base (with dust bin, drawers) and a 2HP/220v motor.

Re: Ripfence for Sears/Craftsman Tablesaw

#29

Do it.

Lee Schierer McKean, PA

I have a Craftsman TS about the same age and configuration. I upgraded to a Biesmeyer fence a number of years ago and the only regret I have is that I didn't do it sooner. The stock fence was a pain to use and you always had to check it to insure it locked up parallel to the blade. I no longer have that worry with the Biesmeyer. As a hobbyist, I do find it difficult to justify the expense of upgrading to a more powerful saw, when my well tuned craftsman does all the cuts I need.

As you can see my table extensions are grids. I had to relocate the rear glide pad on the Biesmeyer fence to align with the rear web on my table extensions. This amounted to drilling two holes in the bottom of the fence at the new location and carefully prying the existing glide pad out of its holes so it could be moved. As I recall installation took less than 30 minutes,

My advice is to upgrade your fence.

Lee


img

Re: Ripfence for Sears/Craftsman Tablesaw

#30

Re: Rip Fence for Sears/Craftsman Table Saw

Dale Penkala

Hello Louie

Thank you for responding & I have to tell you you have a beautiful looking setup there! I don't do quite the things your doing but I like to do good work and with a setup like you have I could really do some nice clock work. Anyway again thanks much!

I did actually consider doing something very similar to what you did and that was make a new saw stand with better dust control factors. Not sure if I would do the router on the right side of saw but since I've been seeing some of these setups they are starting to apeal to me a little bit.

Thanks!

Dale

Mid Michigan

Re: Ripfence for Sears/Craftsman Tablesaw

#31

Re: Do it.

Dale Penkala

Hello Lee

Thanks for the input! I'm finding out many are telling me the samething about the fence upgrade! I'm planning on doing it now but I have found some other issues now since starting this project now so I have to figure out whether to completly rebuild the saw from start or just make it work and get a new one to do what I'm looking to be able to do with it.

Thanks!

Dale

Mid Michigan

Re: Ripfence for Sears/Craftsman Tablesaw

#32

Re: Do it.

Carol Reed, Strawberry, AZ

Once upon a time I had a chintzo bench top table saw. It did not have much going for it, but it was all the pocketbook could handle. So. I built a cabinet for it and bought a Biesmeyer fence and mounted it to the cabinet! Squared the saw to the fence. I now own a Grizzly 1023. BIG improvement. Kept the fence. Sold the one that came with the saw.

Dale, I have been following the discussion and know of your concerns. Let me offer this. Remove the sheet metal wings and check just the immediate table table for flatness. If that is good and if you can get and keep your saw in parallel with the mitre slot, you have a good basis for improvement. If you want to re-use the wings, take care mounting them so they don't screw anything else up. In any event the cabinet base to assist with dust collection is a good thing on any table saw.

Now, on the other hand, if new tool lust is irresistible, go for it and let us know what crumbled your resolve!

Re: Ripfence for Sears/Craftsman Tablesaw

#33

Re: Do it.

Dale Penkala in Mid-Michigan

Hello Carol

Thanks for the info! I have now found some other issues with this saw so by the time I would put the money into the saw I'm better off just getting the saw that I'm looking at now. It is the new Grizzly Hybrid ts. The flatness on the saw is so bad even if I had the best fence on the saw it just won't cut anything good and square or parallel.

Thanks!

Dale

Re: Ripfence for Sears/Craftsman Tablesaw

#34

Lee, I'm glad I did not see....

Barry Irby

your setup before I upgraded my fence. As I mentioned above I had a saw with grid wings that appeared to be identical to yours. My solution was to cover the wings with Formica. It never occurred to me to move the pad. Now that I have "solid" wings I am glad I didn't think of that solution. We went outside the box in different directions.