Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

band saw fences again

Posts

band saw fences again

#1

band saw fences again

Jerry Gibbs

Was at a show and looking at a Carter magnetic band saw fence. The salesman said the secret was in a well tuned saw (using Carter guides). He then eyeballed the fence alignment and sawed a thin even slice approx 6" thick. He then kicked the fence out of his original alignment and produced a nice slice. The blade was 1/2". My question is, Carter products aside, is blade "tuning" that critical? Jerry

Re: band saw fences again

#2

Re: band saw fences again

Larry in NW OHIO

Morning Jerry. In my opinion very much so. I have an old, about a 1980 craftsman, and I can do just about as good with a timberwolf blade, and better yet the one from Highland hardware, the woodslicer blade. The woodslicer is a thinner blade so your kerf is smaller. Go to www.highlandwoodworking.com and you can read more about it. Larry

Re: band saw fences again

#3

What I've found...

John in NM

Using half a dozen bandsaws over the years is that a well set up saw cuts about as well as a bandsaw can cut, and a poorly set up saw is just awful. My belief is that if the wheels are co planar and the frame straight, the guides don't matter a whole lot and you can resaw nicely with just a point fence. Slap fancy guides on a saw where the wheels are out of whack, and you still have problems. Use a good saw with those old, rudimentary friction guides and you find they work just fine. I don't understand the emphasis on fancy fences either - they work well if the saw cuts straight, but just by the nature of a bandsaw they'll work just as well out of square as in square. The difference is in whether the saw cuts straight, nothing to do with the fence.

Re: band saw fences again

#4

Jim in Burlington Ont.

Just to Add to Your Thoughts ...

Jim in River Oaks, Ont.

Hi John,

I am with you on what you said, the only thing I might add is correct tension, setting it so it does not "flutter" is my gauge to correct tension, after that I have found that I am able to get true cuts with no problem.

Take care,

Jim

Re: band saw fences again

#5

Re: band saw fences again

Thomas S Stockton

I don't understand what you mean by blade tuning, but I do nothing to the actual blade itself than put it on the saw and set everything to my liking. A well tuned saw is pretty critical but the correct blade is just as important. I used to resaw on a really low budget import 14" saw, you could actually see the upper arm flex as I was cutting. I tuned that thing as best I could ( I would NEVER call it well tuned) and got a good blade and it would cut veneers at 3/32" just fine, they needed a little more cleanup than on my current saw and setting the saw up took more time but it would do it.

Almost all the problems I have ever had with resawing are due to a dull blade, but the key is that once you set up the saw correctly it tends to stay that way and you just need to readjust the guides when you put a new blade on.

I use 1/2" wide blades for all my resawing.

Tom

Re: band saw fences again

#6

Yup, definitely...

John in NM

Even if wheels are true and co-planar, frame straight, etc, one still needs proper tension, and then a good blade helps a lot too. I've noticed a distinct difference between blades I make and Highland's house blade (waaaay better than mine :D). I'm assuming it has to do with tooth angle and set. I also have a wood slicer that I've never tried - waiting until I have some resawing to do instead of just the usual cutting stuff out that is 90% of my current use.

Re: band saw fences again

#7

Re: What I've found...

paul in AZ

Agree with John. When the blade is properly set up the fence or guides become secondary.

I have a Jet 18" and the fence is not plumb. I worried about that for a while and even tried a shopmade resaw fence for a while then figured out that when a good sharp blade is set up right and the bottom edge of the wood is flat I can make straight, flat cuts with ease. One thing that makes it easier is a magnetic on/off feather board that keeps the bottom corner of the wood up against the fence. That keeps the wood itself from wandering. A point works just as well but I am used to my system. My favorite blade is a 1/2" Timberwolf.