Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Polishing Concrete

Posts

Polishing Concrete

#1

Polishing Concrete

Jennifer Indy.USA

We're in full swing of concrete polishing here. It's looking great! A few more grits to go through and we'll be finished. I think we are to 800 and now we have to fill the tiny voids from air bubbles, then start up again going up to 1200-1600.

Bless his heart...soaking wet and soggy shoes.


Re: Polishing Concrete

#2

You know what I would like to see,

Keith Newton----Little Rock, Arkansas

I think you ought to take that thing back in the shop, and go to work on it in there. There are a lot of us out here that would love looking at those streaks of slurry lines dripping down on those clean white walls of your shop.

I know that would do me a lot of good, and I'll bet there are others who would feel better about ourselves if you didn't set the bar so high on the tidyness scale. ha

Re: Polishing Concrete

#3

Re: You know what I would like to see,

Joseph Mulherin

Jennifer.....is that an electric tool he is using to polish the concrete???? He should use an air compressor driven tool to prevent from being electrocuted. But the pictures are showing you have a very nice smooth finish.

Re: Polishing Concrete

#4

Re: Polishing Concrete

Larry in NW OHIO

Joe I`m betting it`s an air tool, just from looking at the size of it. Larry

Re: Polishing Concrete

#5

Yup, it's an air driven grinder...

Jennifer Indy.USA

....it might get a little exciting if it were electric.

Re: Polishing Concrete

#6

Re: You know what I would like to see, 

Jennifer Indy.USA

Now we couldn't not that....

Here does this make you feel better.

This was how things used to be :\

I'm glad those days are over :)

It's hard to believe its the same space.


Re: Polishing Concrete

#7

Getting Closer

Don Orr

To the install. Bet you can't wait to get this done. And soggy shoes are good for the soul-or is that sole ;-)) Keeps you humble. ;)

I like the drip setup-very clever.

Re: Polishing Concrete

#8

OK, I feel better,

Keith Newton----Little Rock, Arkansas

Now can you come by and show me how to transform my shop. he he.

I know you must be excited to see this project finished. The few times that I have done concrete tops, I was astounded by how much work they consumed. For that, I will celebrate with you. K

Re: Polishing Concrete

#9

Jim in Burlington Ont.

Re: Polishing Concrete

Jim in River Oaks, Ont.

Very nice,

Clay works really hard, looks like he's done this before.

:)

Re: Polishing Concrete

#10

Jim in Burlington Ont.

Re: You know what I would like to see,

Jim in River Oaks, Ont.

Yikes, That old space sure looks like it is best forgotten now that you have that amazing new space. :)

Re: Polishing Concrete

#11

Re: Polishing Concrete

Galen Vetterick

Thanks for posting the pictures of the progress of your creative project. Way too much time and work for me, but then I'm still a formica kind of guy. Yah, a little flaky.

This has helped fill in for the lose of two of my favorite shows "Made in America" or the Canadian "How It's Made".

Your dog seems to be unphased by the noise. He must be a shop dog to put up with that air grinder.

Looking forward to the next in the series of final polish and installation!

Re: Polishing Concrete

#12

Re: Polishing Concrete

Joseph Mulherin

Jennifer, I have followed your project closely from your postings. Clay must be a very special guy to undertake such a project....you have chosen a GEM of a guy for you mate.....and he has also in you.

Re: Polishing Concrete

#13

Re: Polishing Concrete

Mike

What do you fill the tiny air holes with?

Re: Polishing Concrete

#14

Re: Polishing Concrete

Jennifer Indy.USA

Mike, I'll let Clay reply to this but I think he's just using the Portland cement with no sand? He's using a small flexible squeegee to get the mix down into the tiny voids.

Jen

Re: Polishing Concrete

#15

Re: Polishing Concrete

Jennifer Indy.USA

Galen thanks. Sometimes it's best to just watch this stuff than to actually do it yourself. I know I could have never done this project on my own. I know my limits. It's been a ton of fun making this and watching it develop. I've learned a ton.

That's Jackie Lynne in the background. She's a great shop dog. You're right she's not skittterish at all from the noise of tools running. The only thing that gets to her is the tornado siren that goes off every Friday morning at 11:00am for testing. That sends her into coyote howling mode! We hate that mean ol' siren!

Jen

Re: Polishing Concrete

#16

Re: Polishing Concrete

Jennifer Indy.USA

Joseph, all I have to say to that is....yes, yes and yes :)

Glad you're enjoying the progress pictures.

Jen

Re: Polishing Concrete

#17

Re: Polishing Concrete

Bruce, a MN Galoot

Does he have to repeat the polishing process after filling the voids, or is it just a minor touch-up at that stage? This has been an interesting process, which I'm contemplating for our own kitchen to replace formica. Thanks for posting such a detailed exposition.

Re: Polishing Concrete

#18

Re: Polishing Concrete

Mike

Thanks,

The reason that I ask is that we have a new IceStone concrete countertop which was has hundreds (thousands) of tiny holes irregularly spaces across the surface. They have sharp edges which catch your fingertips when you run your hand over the surface. This causes the surface to seem dirty to the touch - the sharp edged little holes are translated by feel into the impression of small gritty stuff on the surface - even tho the surface is very clean.

Watching someone run their fingers over the surface for the first time is interesting - they invariably lift their fingers and feel of the tips with their opposing thumb expecting that they have picked up grit.

I would like to eliminate that as it makes a beautiful looking countertop unpleasant to touch.

Mike

Re: Polishing Concrete

#19

Re: Polishing Concrete

clay foster

Right now I've got the surface polished to 400 grit and all the little air holes and voids filled with a Portland cement slurry. After the slurry has set, I'll begin polishing again with 800, then fill and polish with 800 until all the pinholes and voids are filled. Then I'll polish with 1500 and 3000. I'm not an authority of concrete counter tops, but my test samples have come out pretty nice with this protocol.

Concrete is a fascinating material once you begin to play with it. I've got some art piece going right now with concrete components, and some ideas for furniture with concrete components.

Re: Polishing Concrete

#20

Re: Polishing Concrete

clay foster

Mike,

I'll be filling all the little holes with a slurry of Portland cement. I don't know how this would work with your Icestone, but you might try it on an inconspicuous spot.

I do know that all those little holes are just like a cheese grater on wet finger tips when polishing. You don't even realize your fingerprints are gone until you start seeing blood on the concrete.

Re: Polishing Concrete

#21

Re: Polishing Concrete

Mike

Clay,

That might work. The problem is that the surface is already polished by the supplier and the counter tops have been installed. Actually there is another problem in that the surface has been sealed and then waxed, so I suspect that getting a filler to adhere at this point may be a stretch.

It's a really visually attractive material - the aggregate is bb to pea sized sea shell and green glass fragments in a stark white cement base. Somehow the factory fill coat was compromised and it released, leaving the "cheese grater" effect in places. I'm trying to come up with a way to save it rather than have it torn out and replaced - so far I've not had a genius moment. We have determined that the supplier attempting to separately fill each individual hole is not the answer. I think that if anything is going to work it'll have to be something like a fine slurry pressed into the entire surface with a squeegee like you are doing. The trick is going to be getting it to stay in place once done.

Mike

Re: Polishing Concrete

#22

How about epoxy?

Ray Thompson - Middletown, in

Clean the wax and sealer with the appropriate solvent then mix something like granite dust, white cement, or even inlace in epoxy, then re-polish the surface.

Ray

Re: Polishing Concrete

#23

Re: How about epoxy?

Mike

That sounds like it may work.

Thanks for the ideas.

Mike