Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

OT Wheels and axles?

Posts

OT Wheels and axles?

#1

OT  Wheels and axles?

Thomas Norton

I am an archer when I am not woodworking and I have a question.

I have an archery target stand that I want to make mobile. I bought some pneumatic tires @ Tractor Supply and would like to attach them to this 2x4 stand.

So what do I use for and axle? If I use a bolt would I use a regular steel one and just grease it real good?

Advice??

Thanks

Re: OT Wheels and axles?

#2

Harbor Freight

Dustmaker Mike

I would head to harbor freight and buy one of there small trailer frames. It comes with wheels and axle. You just add the deck and away ya go.

Re: OT Wheels and axles?

#3

Jim DeLaney, Austintown, Ohio

Re: OT  Wheels and axles?

Jim DeLaney, Austintown, Ohio

A bolt will work - preferably a long one with an unthreaded shank that's long enough to go through the wheel's bearings, so the bearings aren't riding on the threads.

Other than that, I'd use a length of cold-rolled steel rod, and drill the ends for cotter pins.

Re: OT Wheels and axles?

#4

Re: OT  Wheels and axles?

Phil Joines

With the light weight you're talking about a couple of long lag bolts would work.

Re: OT Wheels and axles?

#5

Re: OT  Wheels and axles?

Larry in NW OHIO

Tom If I have the right picture in my head how your fram is, 2x4`s on the bottom, I would take the wheels you have back. Then get 2wheels with swivels on top of them and 2 that are fixed and just bolt them on the fram. Larry

Re: OT Wheels and axles?

#6

Re: Going Mobile

Mark Mandell - Gone Round In Jersey

2 tires will be sufficient to make a "barrow" configuration to roll your target down-range. Larger diameter tires will make things much easier to roll over rough ground; 12" should do. Assuming you're doing so in the back yard (or North 40) a pair of large bolts (diameter of the wheel bushings) will be fine for axles; you'll need to double-nut them and shim out with washers to clear the wood frame.

One thing not mentioned is protection; not for you, for the tires. You'll be unhappy with a low shot that deflates your mobility, so plan on a steel shield for those tires. You should be able to get a couple of pieces of cold rolled 1/8" sheet at a local junk yard that you can bolt to the frame in front of the wheels in case the wind shifts.

Re: OT Wheels and axles?

#7

Moses Yoder

Re: Going Mobile

Moses Yoder

Shielding the tires would depend on the accuracy of your shooting. When I was shooting a bow I had a 70 lb draw compound with pin sites and peep site combination. I was shooting all my arrows into a 2-1/2" diameter circle at 40 yards. I wouldn't see any need to shield the tires for that setup.

Re: OT Wheels and axles?

#8

Re: Shoulder bolts are ideal for this

Larry Clinton At Frankfort, (Central) Indiana

If you have a local supplier or machine shop in your area look at shoulder bolts. These are Hardened steel with polished shanks and a reduced thread on the end. They are socket head (allen wrench type) and will allow the wheels to turn with little friction. These would require a threaded metal bracket or plate to screw into - I don't know your skill or what equipment you have available. A site that has the specifications for these bolts is http://www.smithfast.com/shoulderscrew.html

Another option is to purchase lawn mower axle bolts - these are available at nearly any lawn mower repair shop and are quite cheap. A simple way is also to use lag bolts and bronze bushings/bearings. Use a couple of washers and a bushing that has the OD that corresponds to your wheel ID and that is slightly longer than the wheel width and it should last forever.

Re: OT Wheels and axles?

#9

Re: Going Mobile

Joseph Mulherin

WOW, Moses, you and Robin Hood must have been great with your bows.

Re: OT Wheels and axles?

#10

Moses Yoder

Re: Going Mobile

Moses Yoder

Modern bows are extremely accurate with the right sights, especially with carbon fiber arrows. If Robin Hood had a compound bow he would have taken over the world. If the Indians would have had modern compound bows we would've never taken over this continent.

Re: OT Wheels and axles?

#11

Clint Searl

But....

Clint Searl

...could you hit the broad side of a speeding buffalo while riding a galloping pinto bareback, wearing only a breechclout? :b

Clint

Re: OT Wheels and axles?

#12

Moses Yoder

Re: But....

Moses Yoder

I don't like Pintos, they are known for exploding when hit in the back. Something to do with having a big gas tank back there and not much around it. But I do normally wear just my loincloth with beads and feathers and love the freedom it brings me, especially in the winter. I haven't shot a bow in 5 years or so and now thinking about it makes me want to try it on buffalo. There is a buffalo farm close by here, and we have a wild miniature horse in our back yard; I think he could hold my weight. I bet my wife would take me back to the mental hospital if she catches me.

Re: OT Wheels and axles?

#13

How fast RU towing this target???

Frank on Chestnut  Hill