Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Shop Accident

Posts

Shop Accident

#1

Shop Accident

Barry Irby

A couple of years ago I epoxied a brush onto the under side of table insert on my TS to improve the performance of the dust collection. A few days ago my son announced that it fell off. (Not sure that it fell off EXACTLY, but at least he mentioned it.) I am in the habit of laying a pencil or piece of chalk in the top of the Biesemeyer fence. The brush got laid there. Today I was ripping some stock and somehow the brush got knocked off the fence and found the blade. It flew back and hit me on the opinionated finger on my right hand. I have a fairly deep scratch/cut about half and inch long. I am just glad its not worse and that it did not decide to go for my face.

So, lets be careful out there and don't lay random junk where it can take the suicide leap into the saw blade.

Re: Shop Accident

#2

Re: Shop Accident

Bill Howatt

Glad it wasn't worse, Barry.

I will freely admit I'm not the neatest and tidiest person but I do take care there are no tools or other items including pencils on the table when I turn the saw on. Well, I'll be honest, I leave stuff on the right-hand side of the fence but nothing on the working side.

Bill

Re: Shop Accident

#3

Dale Lenz

Thanks for the warning

Dale Lenz

Hope you heal well, Barry. I've been laying Stuff on my Beis fence for 25 years, and have often thought of something vibrating out of the fence to the blade. Now I know it's possible.

Heal quick,

Dale

Re: Shop Accident

#4

Re: Shop Accident

mdclor

Barry,

I'm glad you weren't seriously injured. I also keep a couple small items in top of my fence, but I have a few rare earth magnets there as well to hold them in place. Maybe this will help others with similar habits.

Merle

Re: Shop Accident

#5

Dale Lenz

Good idea, Merle, Thanks!

Dale Lenz

Re: Shop Accident

#6

Re: Shop Accident

Stuart Hough

Hope you heal quickly Barry. I too had a table saw "accident" the other day. I had cut some MDF for a straight edge jointing jig and thought I had dropped the blade below the table. Turned the saw off and waited for the blade to stop. I then proceeded to wipe the MDF dust off the table when BAM! I wiped my hand across the stationary blade, which was still about 3/16" above the insert. Caught the "opinionated" finger in the meat on the first section above the palm and pulled away a piece of callous. MAN did that hurt! Thank God I had turned the machine off!

I've been told that coordination strikes about once every 6 seconds. I guess I had witnessed it missing the mark on that one.

Re: Shop Accident

#7

Ellis Walentine

Lessons learned

Ellis Walentine

I once tried (inadvertently) to crosscut a Yankee screwdriver on a radial saw. (Can you say carbide teeth embedded in cinder block walls?) As obvious as it sounds, you just can't give saw blades a chance to connect with anything but the wood you want to cut. Sometimes we learn the hard way.

Ellis

Re: Shop Accident

#9

Re: Lessons learned

Barry Irby

Way back, a friend and I were working our way through college building kitchen cabinets. We had one of those "wobble cutters" that makes dados. This was a hub with long teeth, and you dialed in the width of the cut. I was cross cutting a dado with a RAS. There was a huge wood stove behind the RAS. When I stopped, I noticed one of the teeth was missing. I have no idea where it went. Did not hear it hit the stove. It did not come out the front and hit me. We never found it. It scared me so badly I never used that thing again. Another friend tried to loan me his because you could dial in exactly the width you need. Turned that down too. That tooth was certainly bigger the a .22 bullet. I just found out the other day that my friend still has it and uses it occasionally. Gives me the willies.

Re: Shop Accident

#10

Ellis Walentine

Re: Yikes,

Ellis Walentine

Yep, that was back when I first hung out my shingle, in the mid '70s. Haven't run over anything since. :)

Re: Shop Accident

#11

Re: Shop Accident

Ron in Eugene, OR

Wow, that is a habit I am guilty of as well. I certainly will need to rethink what I put on the Bes fence, if anything in the future. Hope you mend quickly Barry.

I used to be one that never used a blade guard because I thought I was a very safety minded person. However, after I cut a nice slice into the end of my left hand thumb last year, which fortunately only required a half dozen stiches I decided a blade guard would HELP keep me from making mistakes due to a temporary moment of pure stupidity.

Just wondering, when each of you had you're mishap did you have a guard in place?

Not preaching here - just something to think about. HTH

Ron

Re: Shop Accident

#12

Re: Shop Accident

Barry Irby

No, I did not. Never have and I should. Like you I think I am safety conscious. But your mind only has to wander once and you get hurt.

Part of me would like to have an over the blade dust pickup and guard. I have resisted that because I have a small shop and it seems it would be in the way. I was at WoodCraft yesterday and paused to look at he setup on a couple of saws. Its time to rethink this.

Re: Shop Accident

#13

Re: Shop Accident

Ron in Eugene, OR

Hi Barry -

I never liked the blade guard that came with my Delta cabinet table saw so I made my own over arm. I have it hooked to my shop vac as I still don't have a nice big collector. I got the plans from a web site that is no longer there. I probably have the plans around somewhere. email me if you are interested.

Ron

Re: Shop Accident

#14

Re: Shop Accident

Ron Jones

I'm really glad it wasn't worse than it is--that's bad enough isn't it? Now my 42 years of being a shop/tech teacher will come out; I can't help it. Put a guard on that machine! I know they are a pain; I hate them. But they work. Sorry. old habits are hard to break aren't they?

Re: Shop Accident

#15

Re: Shop Accident

Larry in NW OHIO

Barry When I made mine I think I got the plans right here from WC. Maybe someone will remember where it`s at if we still have it, I tried to look around but could not find it. I think I still have the plans, I could copy and send them to you. Larry