Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Beall tilt box

Posts

Beall tilt box

#1

Beall tilt box

Paul Blackwell

I just tried out my new Beall tilt box which I used to set the angle of tilt on the table saw. I've been making hexagon boxes and have had problems in the past getting the angle perfect. The slightest fraction of a degree off when trying to put together the twelve ends of a hex box leads to poor joints. The tilt box is a digital setup. Zero the box out while sitting on the saw table (doesn't matter if the table is level or not) and with the blade fully up, slide the box over to the blade. The box is held by built in magnets. The readout is in hundredths of a degree. I set it at exactly 30 degrees, and the box came out perfect on the first try. There are a couple of other brands available,but I bought the Beall because it has a nine volt battery and others use a watch battery which reportedly has short life.

Re: Beall tilt box

#2

Re: Beall tilt box

George Colonel's Workshop-Havertown PA

Good Afternoon Paul,

I am a fan of tilt box. Beale replaced my first one because it was defective. Second one was perfect. A very fine tool.

George

Re: Beall tilt box

#3

A.J. Hamler

Re: Beall tilt box

A.J. Hamler

I love mine, and use it on every adjustable table or tool I have -- table saw, band saw, disc sander, etc. It's one of the few tools I own that if something happened to it, I would go out immediately that same day and buy a replacement.

Re: Beall tilt box

#4

Re: Beall tilt box

del schisler

I have had the beall tilt box right after it came out. The first one's came out and wouldn't stay on 0000's I called then and told of the problum . They sent out a replacement right away. The one i have now work's fine. I have every thing set up with the beall. Sometime's i could use it on myself. after a night at the pub. oh well i finily get stablelized

Re: Beall tilt box

#5

Re: Beall tilt box

Stuart Hough

I like the measurement to the hundredth, I might have to replace my Wixey. It only goes to the tenth.

Re: Beall tilt box

#6

A.J. Hamler

Oops...

A.J. Hamler

Wasn't till I saw Stuart's post that I realized that mine is a Wixey, too, and not a Beall. Sorry about that. Faulty memory. Probably need to change my battery.

Re: Beall tilt box

#7

Re: Beall tilt box

John Lucas

Mine is a Wixey I use it for all sorts of things. If you need to set the miter gauge to an exact angle. Zero the gauge on the table saw table. Then set the face of the miter gauge on the table so the bar hangs straight down. Put the angle gauge on the bar and adjust the angle until it's dead on. This really really works well.

I use it on my metal lathe when placing things in the vice. I simply put in on top of the work and adjust it to either perfectly level with the bed or set whatever angle I need.

Re: Beall tilt box

#8

Re: Beall tilt box

FredD

Good tip John , one I haven't tried on my Wixey.

FredD

Re: Beall tilt box

#9

Re: Beall tilt box

Nick Tuzzolino

Re: the one with the watch battery. Take the battery out when not in use and this will greatly prolong it's life.

Re: Beall tilt box

#10

If you happen to have

iew

If you happen to have an IPhone get the "clineometer" App, it is great for leveling and setting angles.

Re: Beall tilt box

#11

Re: Beall tilt box

Alan in Little Washington (NC)

Have you seen the new Wixey? It runs 2 years on AAA batteries. It has a tilting display with both relative and absolute (center of the earth) displays!


Re: Beall tilt box

#12

Re: Beall tilt box

FredD

Don't forget the handy little level display.

FredD

Re: Beall tilt box

#13

Re: Beall tilt box

Phil Joines

Try using a thin piece of plastic to insulate the battery instead of removing it.

Re: Beall tilt box

#14

Re: Beall tilt box

Nick Tuzzolino

Thanks, Phil. That makes it less of a PITA.

Re: Beall tilt box

#15

Dissapointment

Jon

After reading about the Beall and other digital angle gauges I bought one for my birthday. It's a dissapointment. I guess I should have quantified what .1 degrees actually is before buying it.

If I use the tilt box to set a 90 deg. angle, the gap of light I see between my machinest's square and the blade/fence/etc. looks shockingly large. I did this several times and checked it with feeler gauges and got a run of .008 over a rise of 3.165. I interpret that as 0.14 degrees off.

Even if it was .1 degrees off, the gap would still be .006. It doesn't sound like a big number, but when I check it against a square or an adjustable drafting triangle I find an innacuracy that I never accepted in the past.

Maybe I recieved a defective one? But even if it soes read within the stated accuracy, I don't see much use for it.

Re: Beall tilt box

#16

Clint Searl

Re: Beall tilt box

Clint Searl

I wouldn't know one if it bit me on the leg. What difference does it make? How does it show up in your work?

Clint

Re: Beall tilt box

#17

Re: Beall tilt box

Jon

I thought it might make a difference to some one else considering buying the Beall Tilt Box. As far as my work goes, it would create joint gaps that I would consider to be sub-standard.

Re: Beall tilt box

#18

Two Ways

Mark Mandell - Gone Round In Jersey

1. Makes tuning the tools more accurate. Most every "stop" is adjustable and the box gives consistency between different tools. I do, however, use a fixed square to set the 90� stops.

2. Makes setting bevel cuts much easier than trying to fit a protractor between a table and a blade.

3. Saves space in the tool drawers. I used to have a whole bunch of templates for setting blade and jointer tilt angles [don't expect me to "trust" those machine angle gauges all the time do you?]. Now I have room in the drawer for lots of other stuff that I can put in there and forget I have. :D

Re: Beall tilt box

#19

Re: Two Ways

Jon

It's my OCP kicking in.

I would always be double checking it with a square or my adjustable drafting triangle and end up spending more time than I would if I didn't have it.

I'm not as bad as Monk. I think.

Re: Beall tilt box

#20

Re: Dissapointment

Bob Lang

That's the issue with these devices for me. The fact that it's digital gives you some faith in it, but .1 degree isn't close enough. Consider a mitered frame, four corners with two angled cuts each multiplied by a teeny-tiny gap equals one big gap when you put the frame together. I have the same issue with digital calipers that read in fractions. The device rounds off the actual measurement to reach the fraction so you're off by a few thousandths with every measurement. Digital displays don't always mean accuracy.

Bob Lang

Re: Beall tilt box

#21

Uses?

Jon

I hate returning things that might be valuable in some way that I haven't yet invisioned. Have you found a good use for a digital angle gauge with �0.1� accuracy?

Re: Beall tilt box

#22

Caveat

Mark Mandell - Gone Round In Jersey

Each time I get it out to use it, I run it through the calibration procedure. In the beginning, I checked it with my Starrett adjustable triangle. I found it within tolerance which is, for my woodworking, close enough. I'm not a machinist, however, and I just don't need 1/10,000 accuracy on wood cuts.

There are treatments for OCD :D :D

[Nanu-Nanu]

Re: Beall tilt box

#23

Moses Yoder

Re: Uses?

Moses Yoder

I use a sliding T-bevel and protractor to set my angles. You set the bevel so it is at an obtuse angle; this way it goes on top of the blade, not underneath. Of course a lot of people need more gadgets than I do plus it gives them bragging rights for having spent the most money on their shop. Lee Valley makes a very nice tool for setting T-bevels which I don't have yet but might someday, then I will have a miniature bragging right. If you are building a model boat, the Beall tilt box could be used as the anchor, depending on the size of the model. I hate digital gadgetry with a passion. I'm thinking of starting a non-profit organization to fight the spread of this albatross around our necks.

Re: Beall tilt box

#24

Re: Dissapointment

Galen Vetterick

I got an iGaging Angle Cube so probably a cheap knock off.

I can zero it out on the table saw, put it on one side of the blade and set it to 90 degree. Turn the cube around so same side is on the other side of the blade and it indicates it is not 90 degree. Repeatedly rock the blade back and forth to split the differnece in readings but never get the same settings twice.

Went back to my drafting triangle.

Using a better digital gauge do you check it to both sides of the blade and get repeatability?

Re: Beall tilt box

#25

Re: Dissapointment

Jon

"Using a better digital gauge do you check it to both sides of the blade and get repeatability?"

No. Same results you get.

Free shipping from Amazon both ways, so it's on its way back for a refund without any loss other than my time.

:^)