Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Router Sub Base

Posts

Router Sub Base

#1

Router Sub Base

Thomas Norton

I have a Porter Cable Router, 3 1/4HP. And when I need to use a rabbetiing bit I have to use my homemade Lexan sub base with a larger hole in the base. The problem is no matter how much I wax it it does not slide easy for very long. The black OEM base works great.

Any ideas where I can get a "black" base with a large hole?

Thanks

Re: Router Sub Base

#3

Clint Searl

Re: Router Sub Base

Clint Searl

Rather than waxing it, the answer may be roughing it up with 80 grit paper to make contact less intimate.

Clint

Re: Router Sub Base

#4

Re: Router Sub Base

George Colonel's Workshop-Havertown PA

Good Morning Tom,

I have the P+C 7518 router. It is mounted in a table permanently, so I don't share your problem. I do all of my free hand routing with my P+C 690 series routers, including one with a a plunge base for morticing. That could be an alternative for you.

Otherwise, I'd purchase another black base from P+C and adjust the opening to suite your needs.

The 7518 or the plunge version are too heavy for me to manage out of table, so the lighter 690 remains my choice for that mode. It has enough power to spare.

George

Re: Router Sub Base

#5

Re: Router Sub Base

Larry in NW OHIO

Tom I have some of the slippery front with a tape backed that you could put on your router base and it would slip like it had Teflon on it. If you would want some to try just send me your address and the size of your base and I`ll send you some. Larry

Re: Router Sub Base

#6

Re: Router Sub Base

Thomas Norton

Larry,

Thanks for mentioning it. I have some of that kicking around the shop. Will give it a try.

Re: Router Sub Base

#7

Re: Router Sub Base

Bill Houghton, Sebastopol, CA

I'm not sure what plastic those sub-bases are made from; but you might be able to customize your hole size by just plunging through a standard base with the bit you want to use. I've made several acrylic bases and used that approach to make the center hole. With the P-C routers, if you clamp the base down over a hole and carefully spin the motor down into the base, you can "plunge" even if you don't have a plunge router.

Re: Router Sub Base

#8

Re: Router Sub Base

Carol Reed, Strawberry, AZ

FWIW, Lexan, polycarbonate is softer and thus not as slippery than Plexiglass, acrylic, since Bill mention acrylic, and you mentioned Lexan. The black sub base is likely not either. You've gotten some good suggestions.

The factory base is milled for template guides, so I'd likely just make a new one out of acrylic and be done with it.

From the retired Router Lady, for whatever that's worth. :)

Re: Router Sub Base

#9

Re: Router Sub Base *LINK*

Barry Irby

Pat Warner makes sub Bases. I got his name here. I know nothing about him and have not used his products, but I might be a place to start.

I made one out of a scrape of some sort of clear plastic I had laying around. I don't know what it is, but its too soft. It would be better to use something harder. Maybe somebody can explain about which is harder and I thin some of them have a hardened face. My router had a flat side on it which I hate and have never found a use for so when I made my sub base I mad it round. I like it. Its a bit crude, but entirely functional.


Pat Warner Sub bases

Re: Router Sub Base

#10

Re: Router Sub Base

Howard Norman

I purchased a couple router bases from Par Warner several years ago. I have had one installed for about three or four years now. I consider the two that I purchased to be good products.

Re: Router Sub Base

#11

Re: Router Sub Base

del schisler

I don't belive i would wax it. Wax may get on the wood and the finish wouldn't stick to the small wax that may be left behind. Buy another sub base and drill out the hole or if you have a leath turn the hole just the way you want it. Or a friend may have a leath to help you out ?? You can use double face tape and a piece of wood and put the sub base to the face plate that goes on the leath ?? Been their and done that my 2 cents

Re: Router Sub Base

#12

Re: Router Sub Base

Tony - Memphis

Me too. I have a few of his bases and they are really nice. I got one that had a slight flaw and he replaced it pronto and told me to fix the original and keep it. It was only a slight flaw, but he took care of it.

Tony