Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

Shop Ideas

Posts

Re: Shop Ideas

#26

Re: Green, Generally

Don Orr

Very nice looking place Jim. Nice spread-lots to mow. Is this near where you are now? Best of luck with the whole process.

Re: Shop Ideas

#27

Re: Shop Ideas Dust Collector

matt overton

Just an idea to consider. When I put my cyclone system in, I didn't want to lose shop space, so I installed it in the attic of the shop. The unit fit on an end wall with the trunk lines tucked in the eaves running the full length of the bldg. I put 12 drops at the locations I needed. The barrel is in the shop connected thru the ceiling by 8' of pipe. This solved many problems. The sound is muffled by the attic, the collection barrel is the only space taken up in the shop, and there are no trunk lines taking up valuable wall space ( I only have 7' 4" headroom). I wish I could have installed this into an empty bldg, it was a nightmare working around an existing shop.

Re: Shop Ideas

#28

With a shop like that....

John in NM

You'll need to have a TV show! Just don't paint it grey :D

Nice building Jim, I don't think I'd get any work done around there in the summer :D

Re: Shop Ideas

#29

Re: Shop Ideas

Alan in Little Washington (NC)

I would hate to mess up that beautiful facade and the second floor would make a super office, but if you had thoughts about storing wood up there you can do what I did.

You would need to make the windows so they open, or replace them with a loft door, but then you could install a folding I-beam with an electric hoist on a trolley.






Re: Shop Ideas

#30

Not stealthy at all, in my opinion

Bill Houghton, Sebastopol, CA

Re: Shop Ideas

#31

Re: Shop Ideas

Joe Mohnike

Greeeeeeeeeeeeeeen with envy!!!!!

If you decide to replace the floor, you might consider puting the dust collection system in the floor. I saw one where the floor (wood) was on 2x6s with another 2x6 6" over which created the vac chamber. He placed a coupler in the floor where needed to connect the various tools and several doors which he could open to pick up floor sweepings.

I would look at the tools that I have now, and where I want to place them, and then consider what tools I will be buying in the future and their placement.

You can not have too many plugs so don't be shy and have as many circut breakers as possible.

You are living my dream.

Best of luck

Joe M.

Re: Shop Ideas

#32

Jim in Burlington Ont.

Re: Shop Ideas

Jim in River Oaks, Ont.

Wow, that is an excellent idea... I see that being a great solution... I was thinking about a "Dumb Waiter" inside to lift and bring down wood etc, this looks like a solution I will pin to my wall of ideas, Thank You!

Re: Shop Ideas

#33

Jim in Burlington Ont.

Prince Edward

Jim in River Oaks, Ont.

It is located in Prince Edward County in Ontario, 2-3 hours closer to the Lee Valley Mother Ship

;)

Take care,

Jim

Re: Shop Ideas

#34

Re: Shop Ideas

mdclor

Alan,

Thank you for posting this. Your solution is what my feeble old brain was struggling to remember. :) Hopefully, I will remember it well enough now to attribute it to you in the future.

Thanks,

Merle

Re: Shop Ideas

#35

Re: Prince Edward

Mike Rubes, Apex, NC

Hi Jim,

MapQuest says Prince Edward County is about 825 miles from Apex! I am thinking "Road Trip"! I've only crossed into Canada at Niagra about 20 years ago. I vote for the Welcome Jim to his new Home party!

Great pictures, that looks like a wonderful place.

Lots of space is nice.

Mike

Happy for now with 1/4 acre to mow in Apex, NC!!

Re: Shop Ideas

#36

Re: Shop Ideas

Carol Reed, Strawberry, AZ

Wowza, Jim!

Dana pick out her room yet? :)

Re: Shop Ideas

#37

Re: Wire . . .

Don Evans

Concerning the outlets, make sure the electrician understand to put them higher on the wall than they do for house wiring.

Walk to a wall and reach out without bending and touch the wall, that is the height you want all the outlets.

When I had my present shop built that is one thing I did and am really glad I did.

This way outlets are not behind stuff and low to the ground.

You'll be glad you did!

If you can plan on one high outlet 30 amp 220 volt high for present or future cyclone dust collector if you can plan for where it would go.

For a one person shop, one machine, lights and dust collector running at once don't let anyone talk you into less that 100 amp service. Things like hot water heater show up later and it's electric and so forth and so on. Your future plans will change things for sure but one thing you don't want to have to do is run new service to do then because that is usually a show stopper.

Don

Re: Shop Ideas

#38

Re: Shop Ideas

Dominic in Buck

Holy SMOKES Jim! That looks amazingly like my shop.

Oh, did I say "My shop"? I meant "My DREAM shop!" LOL!

Crossing my fingers for ya buddy!!!!

Re: Shop Ideas

#39

Jim in Burlington Ont.

Re: Shop Ideas

Jim in River Oaks, Ont.

Hey Dom,

I see a wonderful tool cabinet on the wall with all my favorite hand tools... my bench in a perfect spot as well, not against a wall...speaking of hand tools I was over at Konrad's yesterday, my heads still buzzing... he's got some awesome tools on his bench right now, and the place smells like mine will, I hope!!

Take care,

Jim