Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Tools Rules

Posts

Tools Rules

#1

Tools Rules

Gary Smyth

Today I was doing some (more) painting for a cousin. I will be paid. After two weeks, off and on, bending in all directions taping and painting around duct work I finally got to the end. Put everything away and was doing a final vacuum. Literally ten seconds from the last, HIS shop vac quit. It was on--then it was off. Checked the breaker for the outlet, extension cords, and everything else with no joy. Now I know my rules with tools. If I lend it and you break it, you owe me. When I told him what happened his rules are more flexible. He says not an issue. The shop vac was second hand and not to worry. We are on great terms, I want no leftover feelings. What would you do?

Note by the way, I have the motor section. I'll check tonight if it might be the power cord to the motor, or maybe the brushes. Still, I need an opinion.

Re: Tools Rules

#2

Re: Tools Rules

Chuck Lenz

I wouldn't worry about it too much. It doesn't sound to me like you abused it, his vac just happened to have failed doing a job for him. I would just chalk it up as his faulty equipment. It's nice of you to try to fix it for him.

Re: Tools Rules

#3

Re: Tools Rules

Bill Houghton, Sebastopol, CA

If you'd borrowed the vac to work on your own or someone else's project, then I think repair/replace would be appropriate.

If you're getting paid at a level that, were you doing it for someone without a vac or other tools, you'd bring your own, then I think discounting your rate somewhat to adjust for your use of his tools - or at least offering to do so - makes sense.

On the other hand, if you're already discounting a bit to a family member, then accepting him at his standard - or doing what you're already doing, which is checking to see if you can repair it - is fitting.

Re: Tools Rules

#4

Re: Tools Rules

Nat Robison

If I was at someone's house working with them (paid or not) and their tool quit while I was using it, I wouldn't feel the need to replace/repair it. It's different if you borrow it and you're using it at your house.

Re: Tools Rules

#5

Re: Tools Rules

Doug Reynolds in Seattle

In my experience, I have made a genuine sincere offer to make the repairs or replace what I think I broke. If the other party said it was not necessary, I left it at that and felt good to leave it there.

Re: Tools Rules

#6

Moses Yoder

Re: Tools Rules

Moses Yoder

He said it was okay. If you want to keep the relationship free of bumps, I would buy him a 6 or 12 of his favorite beverage and tell him it's for the damage to the vac.

Re: Tools Rules

#7

'Universal' tool rules

Tom Dunlap

Everyone else has written what seems like typical tool rules...for people who care. There is the faction of tool users who don't care and have no respect for tools, theirs or others.

At work I put a pole tool on top of some lockers in our storage garage. It was alongside a section of a telescoping pole that got kinked but had many pieces that can be reused/scavanged if needed. When I went to get the pole tool I found that it and the kinked pole were gone. Some of my coworkers had cleaned the garage and tossed the poles...but no one is 'fessing up. Even though the replacement cost won't come out of anyone's pocket it will cost about $135 to replace the pole and I lost a stash of repair parts too. This is an example of people who don't respect tool use, even if they belong to the company.

'Keep your hands off my tools' is another rule in my book.

Re: Tools Rules

#8

Re: 'Universal' tool rules

Chuck Lenz

Yeah Tom, I got one for you. My brother inlaw that makes ALOT more money then I do, and so does his neighbor, decides that he wanted to borrow my wheel barrow, so reluctantly I did, but figured that he is so anal about all of his stuff that I'd be ok. I get the wheel barrow back with concrete allover it. I asked him what the deal was, he says that he loaned it to his neighbor. Well thats great, the same jackxxx that laughed at me when I wanted a measely $15 an hour to build him a shed.

Re: Tools Rules

#9

Re: 'Universal' tool rules

Tom Dunlap

Did you settle for a cement covered 'barrow?

At the risk of angering [i'm being WC PC...hehehheh] someone, I'd send it back to the sloppy neighbor and tell him to get me a clean one. Maybe the two of them will split the cost of 'their' 'barrow :)

Re: Tools Rules

#10

Re: 'Universal' tool rules

Chuck Lenz

No Tom, I let it go before I strangled one of them. But I will tell you this, they pretty much burned the bridge, that will NEVER happen again.

Re: Tools Rules

#11

Long term view

wilbur

My take: however this situation gets resolved, you may want to add some flexibility to your tool rules. Sort of a "goes around, comes around" point of view.

Re: Tools Rules

#12

Re: Tools Rules

john lucas

Gary I haven't read what the others have said yet but here's what I would do. I would offer to buy one. If he said no problem I would offer to split the cost. If he still insists that it's no problem then I would accept that. I think at that point you've done the honorable thing.

Re: Tools Rules

#13

burning the bridge

Dave Peebles Lyons, Ohio

Hi Chuck,

You said.. "But I will tell you this, they pretty much burned the bridge"

I say you should have burned the bridge before you loaned it out. That way they would have had to return it through the river and it would have been as clean as new.

Dave

Re: Tools Rules

#14

Corb Lund: Hard on Equipment *LINK*

Tom Dunlap

Corb Lund is a musician from Alberta. If you don't know him, you should. He writes some great songs.

This is one fits the theme of this thread:

CORB LUND BAND

HARD ON EQUIPMENT (TOOL FOR THE JOB)

He's been roundin� off bolts since the age of fourteen

Was that a five eighths or a nine sixteenths?

He's got a metric socket that don't quite fit

Well it'll wiggle just a little but it ain�t quite stripped

The safety guard�s gone from his grinding machine

He got a stiff paint brush he only kinda got clean

He's the hired man, my neighbor and a cousin in law

He's a jerry riggin� fool, he got the tool for the job

Well it's vise grips for pliers, and pliers for a wrench

A wrench for a hammer, hammers everything else

It just don�t seem to make much difference

I sure do like him but he�s hard on equipment

His corners ain�t square and his floor ain�t level

And he's always had trouble with the old tape measure

His doors don�t close �cause the jamb ain�t plumb

And he�s a Goddamn menace with an air nail gun

They love to see him comin� at the lumberyard store

Fixed the leak in his roof with a two by four

Drilled holes in his boards with the wrong kinda bit

And when they don�t line up he blames the government

Well it's vise grips for pliers, and pliers for a wrench

A wrench for a hammer, hammers everything else

It just don�t seem to make much difference

I sure do like him but he�s hard on equipment

He got the whole front yard full of fix �em up cars

Three don�t run and the rest won�t start

Everything's fine with his rebuilt motor

Except of course for the couple spare parts left over

Baler wire tie downs goin� down the road

On two bald tires and an oversize load

He ain't never read a manual �cause that's like cheatin�

He don't mind a little grease on his hands while he's eatin�

Well it's vise grips for pliers, and pliers for a wrench

A wrench for a hammer, hammers everything else

It just don�t seem to make much difference

I sure do like him but he�s hard on equipment

I sure like you son, but you�re hard on equipment

He�s got busted up knuckles, his thumb got bruised

Jesus Christ was a carpenter, too


Corb Lund Band

Re: Tools Rules

#15

Probable cause

Lee Schierer McKean, PA

I suspect that the thermal protection link in the motor did its job. Sucking up drywall dust can clog a filter pretty quickly. Some vacs use air pulled in through the filter for cooling the motor. When the air flow quits or gets slowed enough long enough the thermal protection link opens and stops the motor from burning up. Most of these on cheap equipment are non-resettable. If you can find it on the motor you have about a 1-50 chance of finding a replacement.

Do you owe him a new vac? Well if you were being paid your normal rate for your work then definitely yes. If you were working at a reduced rate, then maybe. If your labor was free and it was a joint effort to do the work then I would say no.

Lee

Re: Tools Rules

#16

Re: Probable cause I'll bet right

Gary Smyth

Brought home the motor section. The power cable checks out. Checked the on/off switch also with a multimeter and it is operating properly. I unscrewed over a dozen screws to get to the motor and drat, no reset breaker. Thought I'd remove the motor from the housing but it is held by a thin hollow spring washer/clip very firmly set a grooved post that is of a diameter not available in hardware stores and is so thin it is not is designed to be removed and reinstalled. In as much as I have no replacement (it is not available in the parts list) I am stymied and also ticked. A push button breaker would have been so nice. A replacement clip that is "available" would have been OK, if only to go further. Now I can't remove the motor and replace it after I see what else might be possible. I thought Shop Vac was a decent company but there is no alternative offered by them other than to buy the whole vacuum top section which is priced at more than twice what was his cost to begin. Back to square one. I am really frustrated by some really bad timing and dead end repair.

Re: Tools Rules

#17

replacement parts *LINK*

Tom Dunlap

Try this company:


E Replacement Parts

Re: Tools Rules

#18

Thanks Tom

Gary Smyth

but that link provides filters and "disposables" for the model. On a different site I found the part number for the motor alone and the top portion but neither are available in less than two to four weeks, and are expensive. Pretty close to getting a equivalent new unit (discounted). I'll find out for sure Monday when the site has a live rep for parts questions.

Re: Tools Rules

#19

Re: Thanks Tom

Larry in NW OHIO

Gary If I remember correctly, isn`t Shop-Vac the same as Craftsman. I would think they would be interchangeable. When I looked at them, they sure looked the same, except the paint job. Larry