Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Good Hope Hardwoods - Walnut Slabs & Specialty Hardwood Lumber

Starting small engine question?

Posts

Starting small engine question?

#1

Starting small engine question?

Barry Irby

A friend loaned my son a leaf shredder chipper with a small engine it about the size of a lawn mower engine. Its a Craftsman unit. It was put away with fuel in it. We dumped the old fuel and put in fresh. It would not start. At his suggestion we put a few drops of fuel in the air filter (did not have starting fluid) and the motor would fire and run for a few seconds. He said that last year they had to do this over and over until it got hot and then it would run. We did it about ten times, but no joy. I know nothing about small engines, but since it runs on fumes I assume the spark plug is firing. Since it stops after it uses up the fumes I assume the gas is not getting to the engine. I looked for a gas cutoff and did not find one. So now I assume it is the carb. Is there a way to clean the carb without disassembling the engine? It appeared to me the carb was tucked up under some sort of cowling. This is a borrowed piece of crap machine that has not been treated well and I don't want to spend money repairing it. Any suggestions?

Re: Starting small engine question?

#2

Re: Starting small engine question?

Dave Paine

Barry, I once had a weed wacker, happened to be Craftsman, which had similar behaviour in only the second year. This was not due to abuse, rather the "pump" in the carb drying out, which I found out later.

I was so frustrated at the unit not working, I gave it to a colleague. He showed me the little flapper diaphragm which was the "pump". He replaced this and it worked. I did not want the unit back, and bought a different brand, which is still working.

In principal as the piston opened, it was meant to cause partial vacuum, opening the diaphragm and sucking in some fuel. On the up stroke it was meant to close the diaphragm. Once this dried out it would not flex, thereby starving the engine of fuel.

Sounds like your unit is starved of fuel for some reason. Could be similar cause, or could be a blocked hole/jet.

I think you will need to remove the carb to attempt to find the problem. Good luck.

Re: Starting small engine question?

#3

Jason Roehl in Lafayette, IN

Re: Starting small engine question?

Jason Roehl in Lafayette, IN

Barry,

I have an old 5 HP Craftsman chipper-shredder that my sister originally bought 20 years ago, handed it down to my parents when my sis and BIL moved, and now my parents handed it off to me a couple years ago. I ended up rebuilding the carburetor, but there is a fuel cut-off on it--it's just a little thumbscrew on the bottom of the carburetor float bowl. It's integral to the screw that holds on the float bowl, so it's not obvious. IIRC, it only needs to be open about a half turn or so.

Jason

Re: Starting small engine question?

#4

Moses Yoder

Re: Starting small engine question?

Moses Yoder

If you leave gasoline in an engine for long periods of time it will ruin the diaphram as mentioned. The carburetor could be gummed up as well. Always run all the gas out of the carb before storage. After checking to make sure you are getting gas into the carb, you will probably need to take the carb off, clean it with carb cleaner then blow dry with an air hose, and put in a new diaphram.

Re: Starting small engine question?

#5

Carb Problem

Ralph Lipeles

No doubt it's a carb problem but may not be too bad. I find that when gasoline is allowed to sit in an engine the needle in the carb (it's what the float pushes up to turn off the fuel flow and keep the engine from flooding) sticks. So, buy yourself a can of spray carb cleaner. Disassemble the carb being careful not to lose and small parts. Make sure that when you do the cleaning you clean both the needle and seat. If you do not have an engine manual for setups lightly seat each needle, count the number of turns to seat the needle and then remove the needle for cleaning. When reinstalling, repeat, gently tighten the needle and then back it off to where it originally was.

Re: Starting small engine question?

#6

Moses Yoder

Re: Carb Problem

Moses Yoder

That's true only in carburetors that have a needle and seat operated by a float. This engine probably has the carb setting right on top of the tank with a tube sucking gas into the carb. The action of the diaphram right above the tube pumps gas up out of the tank through the carb into the engine. When the diaphram becomes stiff, no more pumping. I think the diaphram in a Briggs & Stratton is part of the gasket between the carb and tank but it's been a little while and I would have to take one apart and look at it.

Re: Starting small engine question?

#7

Re: Starting small engine question?

Andy Lincoln,in Dearborn MI

Try a cap full of Seafoam.it is a fuel additive I have had good luck with on gasoline engines.just drop it into the fuel tank and wait for the white puffs of smoke.

Re: Starting small engine question?

#8

Re: Starting small engine question?

Larry in NW OHIO

Barry Whenever I`ve had trouble starting a motor, 2 or 4 cycle, I would take the air cleaner off and spray WD-40 into the carb opening, just a second or two, and then full chock it and then try starting. It may not take right away. When it takes hold and burns that up, do it again. Sometimes it takes 4 or 5 times or more but mine allways took hold. Sometimes I would take the WD and spray it into the carb after it is running and use that as fuel untill it is running from it`s own fuel. I have done this for years and it always worked. I think it cleans the carb as you`re trying to start it. On a 2 cycle I think it lubes the inside just enough as to not ruin it. But of course you cann`t use it instead of the fuel. Good Luck. Larry

Re: Starting small engine question?

#9

Dave

Re: Starting small engine question?

Dave

I have an Airens Snowblower that gets used once or twice every couple of years. Same problem this year.

On sage advice, I rapped on the bottom of the carb with the handle of a screwdriver 6 or 7 times. Cured it.

Apparently, there is a little needle valve in there that gunks up.

Worked great.

Could be voodoo or coincidence, but has the advantages of being free and easy to try.

Good Luck.