Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Fixing planer exit roller marks.

Posts

Fixing planer exit roller marks.

#1

Fixing planer exit roller marks.

Virgil Johnson

I solved my planer exit roller marking problem (prior WC post) by removing the serrations from the exit roller by taking a light cut on the exit roller. The exit roller was about .035 larger in diameter than the feed roller to begin with. I took just enough material off to remove the serrations. About .020"

This is the surface of a planed piece of walnut before the turning the roller.


A freshly turned roller and a nervous planer owner at this point.


Finish on a 7/8" wide piece of basswood after reworking the roller. Not so nervous planer owner now.


So far the machine will still eject rough lumber as well as jointed lumber. If it ejects the various sizes of lumber I throw at it over the next few months then it will have been a successful rework.

Re: Fixing planer exit roller marks.

#2

Re: Fixing planer exit roller marks.

Paul Cates - Henderson, KY

Nice job Virgil. I'm glad you had the capability to fix the roller the way it should have been to start with.

Re: Fixing planer exit roller marks.

#3

Re: Fixing planer exit roller marks.

John M in Mid Mich

So my planer has adjustments for the feed roller pressure, and yours were simply pressing too hard relative to where the blades were cutting. I would expect most/all others to have the same. Turning down the rollers seems rather extreme, and the serrations were there for a reason, I would think. Did you try to adjust first?

Re: Fixing planer exit roller marks.

#4

Re: Fixing planer exit roller marks.

Virgil Johnson

Thanks for your feedback/pic on the initial post.

Re: Fixing planer exit roller marks.

#5

Re: Fixing planer exit roller marks.

Virgil Johnson

Did you try to adjust first?

Why would I do something as simple as that?...:-) Yes I tried various adjustments from 'low to no" pressure. The advice I got from the tech line (admittedly a day late) was that the serrations could possibly be too sharp and to try to knock down the tops with emery cloth. Before I went to this extreme I did take the time to research the issue beforehand. I found several posts about this problem all with no follow up as to a fix. I'll report back in a few months on how my solution is working.

Re: Fixing planer exit roller marks.

#6

Re: Fixing planer exit roller marks.

John M in Mid Mich

Sorry. Didn't mean to insult, and wasn't trying to be a smart a#%. Just wondered. I've got a Rojek MSP310 euro combo machine that is currently slipping on the planer feed, that is how I know about the adjustment... The same old "don't ask me how I know that" story.

Re: Fixing planer exit roller marks.

#7

At least larger planers...

McKay

I have experience with an original Oliver and a Northfield. Neither of these planers had serrations. Your fix was in line with the big boys toys.

Re: Fixing planer exit roller marks.

#8

Re: At least larger planers...

Alan in Little Washington (NC)

My old Dela RC-51 has dual "textured" outfeed rollers but no serrations.

Re: Fixing planer exit roller marks.

#9

Re: At least larger planers...

Larry in NW OHIO

Virgil Not to beat a dead horse and don`t mean an insult or anything like that,but I`m just curious. Like I said in one of my posts, when I set machines up in a wood factory we always had serreated rolls at the infeed end and flat ones after the top blades planed the top flat. With what you did, and I hope it works for you, would it not have been the same with what you have now. To my way of thinking, and that is dangerous when I do that, it would have been the same if you would have put the serreated rollers on the front and flat ones on the back and that way I would think you would have more push. The only thing I see wrong with my way is if you can not plane enough off to take out the serreations. Larry