Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Heating a spray booth

Posts

Heating a spray booth

#1

Heating a spray booth

McKay

I currently use an infrared heater (30,000btu) that I purchased from Graingers that uses natural gas.

http://www.grainger.com/Grainger/PROCOM-Infrared-Gas-Heater-6EU22?Pid=search

It does a great job of heating my 1000sq. ft. shop. The problem is when I need to spray using my airless sprayer. (The open flame would not do well with the lacquer fumes.)I am adding a 10x10 room to the back of my shop and I will need to heat it. Are there any ideas out there to heat this 10x10 room? I have considered using a hot oil room heater, but I am not sure if that is a good choice. I have also considered using a small electric hot water heater that would push water through a radiant system.

Give me guidance ohh knowledgeable ones.

Re: Heating a spray booth

#2

Re: Heating a spray booth

FredD

Electric base heaters that heat oil and cycle on and off for economy would work well in a small room and keep it at a predetermined temp.

Venting all of your warm air when you running the spray gun is a problem if the base heater don't recover fast enough.

FredD

Re: Heating a spray booth

#3

Easy solution

Bill Tindall

Turn it off when spraying.

I spray all year. When it is cold I have everything warm inside, move(quickly) everything outside and spray, even when it is below freezing. The warm spray sprays fine. The warm wood flashes solvent just fine. Then I move it indoors to cure. I get the most wonderful smooth coatings when it is cold.

You could do similar. Get everything warm. Turn off heat and spray. After a few minutes turn the heat back on to cure.

Re: Heating a spray booth

#4

Re: Easy solution

Larry in NW OHIO

For future reference if you ever need another Northern tools has 30,000btu blue flame gas heaters for $200. I`ve had one for over 30 years in my basement and have not a lick of troubble with it yet. For your preblem, what Bill said. Larry

Re: Heating a spray booth

#5

Re: Easy solution

FredD

That is a not a solution easy or otherwise.

Using a small unvented room for a spray booth besides being illegal is dangerous in the extreme for finishes such as lacquer.

If you vent the room , in the cold season you will be blowing your warm air outside, but this not a problem if the project being sprayed is small ,if it is large and more then one or two , do it in steps.

The choice of your heat source , cannot be a open flame heater, for the same reason you can't smoke in the environment of the spray booth.

You might try what Bill says , I got a picture in my mind of running in and out with a set of Kitchen Cabinets , all the while praying I don't drop one or get a blush in the finish, but different folk do have different strokes.

Remember what you Fire Marshall and Home Owners insurance says about intentionally creating a situation you definitely would not like.

BTW I use a Graco Airless, always have and always will , for the best of gun off finish.

FredD

Re: Heating a spray booth

#6

Re: Heating a spray booth

Barry Irby

I have a friend with a professional shop. The building is about 72 feet long and 26 feet wide. 12' on one end is a paint room leaving him a 60 foot long shop. He has a 84,000 BTUH propane heater for the shop and a 400,000 gas furnace for the paint room. The big furnace is located in the shop, but draws all of its air from outdoors, heats it and blows it through the paint room and out. No recirculation, just one pass through. Explosion proof fans draw the air through.

When I had a paint room I could not afford such an elaborate setup. I set up a polyethylene lined rooms that was nearly sealed. There was a box fan that pushed fresh air into the room and out through an opening that was about five times the size of the fan. The fan drew its air from a heated space and sucked it through a high efficiency filter. Worked great. If I had had an explosion proof fan I would have set it up to operate under negative pressure and let the fan suck air out of the room and put the filters in the entrance.

Re: Heating a spray booth

#7

PS, the big OOPS.....

Barry Irby

I mentioned my friend's 400,000 BTUH furnace was in his shop, but only connected to the spray booth. It runs on propane which is heavier than air. One day while spraying, he realized the heat had not come on. He stopped and walked out of the spray room into the shop, and as he was realizing that the pilot has failed on the big furnace and that it was dumping gas into the shop, the gas reached the pilot in the shop furnace. BOOM! Fortunately he had built the shop with very large windows and the sashes were held in by some little set blocks that has a small brad or two in each. The explosion blew the windows out into the surrounding yard. Didn't even break the glass. He just changed his pants and put them back in place.

Re: Heating a spray booth

#8

Re: PS, the big OOPS.....

frank ashmore

I use a propane tank with a heater dish on top.My shop is a 1000 sq ft, the spray booth is on the east end of the shop and has an explosion proof fan.I open a door to the outside of the shop on west end and point the heater at the open door and turn on the fan .It makes a nice draft at my back when spraying and the shop stays around 65-67 degrees when its in the 20s outside.One step back from the booth and you cant even smell lac.

Frank

Re: Heating a spray booth

#9

Re: Heating a spray booth

Thomas S Stockton

As long as the room your building is properly vented with a good exhaust fan your current heater will work AS LONG AS IT ISN"T IN THE SPRAY ROOM. If you are worried at all just shut the heater off when you spray and heat everything up and then turn it back on when your done.

Another thing to think about is lighting, explosion proof lights are expensive. I used to have a booth that we used halogen lights set outside of the booth and shined through plexi glass panels in the wall. Worked great and since all the wiring and lights were outside of the booth we didn't have to worry about special fittings etc.

The other thing we did was to take a pair of hollow core doors and cut the centers out and fit furnace filters in them to help keep dust down in the booth, although furniture finish is pretty forgiving compared to spraying anything colored.

These ideas will not work for the commercial type spray booths that are open on the end.

Tom