Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

Why Didn't I Make This Years Ago!!!!

Posts

Why Didn't I Make This Years Ago!!!!

#1

Why Didn't I Make This Years Ago!!!!

Ken Bellock (Houston, TX)

Life is so much easier now! I am working on a toy box/blanket chest for my daughter, and the sides are wider than the capacity of my sliding miter saw, so I made this. I wish I had made this baby years ago! Assembled from just a couple of scraps laying around.

I had just finished ripping the walnut panels for the sides to size, and was trying to figure out how to cut the 15.25" wide panels square before starting on the dovetails. Laying on the floor was an exactly perfect sized cutoff to fit my miter slots for the table saw, so I laid a couple of pennies down in the miter slot, laid the walnut runners down in the slots on the pennies so they would be a hair proud of the table, put some double sided turning tape on the runners, and laid a scrap piece of baltic birch down on the table. Flipped it over, predrilled and countersank holes, and popped in a couple screws. Grabbed the block plane and put a slight chamfer on all the edges and corners. Flipped it back over. Took a really dry scrap of 2x4 that had been in my wood rack a couple of years and ran a face and side through the jointer, then cut it to fit the front and back of the sled. Glued/screwed the 2x4 for the far side of the sled first, just making sure it would cross the cut path. Fired up the saw, and ran it through just shy an inch or two from cutting through the front side. Then I grabbed the starret square, which fit perfectly into the kerf, and glued and clamped the front 2x4 to the sled. This morning I took off the clamps, fliped it over, predrilled and countersank holes for screws, zipped them in, and waxed the runners and bottom.

My first cut was exactly square according to my starret square.


Re: Why Didn't I Make This Years Ago!!!!

#2

Re: Why Didn't I Make This Years Ago!!!!

Larry in NW OHIO

Nice sled, but one suggestion, I would put a saw guard on the back of the sled, if that is what it is called where you stand. To cover the saw blade when it comes through so you don`t cut your hand. Larry

Re: Why Didn't I Make This Years Ago!!!!

#3

Re: Why Didn't I Make This Years Ago!!!!

Bob S

Awesome! That is exactly the motivation I need for me to make my sled which I have needed for years and haven't gotten to. Thanks, and Thanks for the photo.

Re: Why Didn't I Make This Years Ago!!!!

#4

There are few WW jigs that will make life easier

Bruce, a MN Galoot

than an accurate cut-off sled.

Nice job!

Re: Why Didn't I Make This Years Ago!!!!

#5

I recently had the same epiphany......

Bill Tindall

...after taking a class in a shop equipped with a sled. This may be the most overlooked table saw accessory. I made mine from a large piece of 1/2" baltic birch (so I could lift it). Makes cutting panel ends a breeze.

Re: Why Didn't I Make This Years Ago!!!!

#6

Re: Why Didn't I Make This Years Ago!!!!

Mike

I know you already know this but take great care where your hands are when the sled passes the fence.

Re: Why Didn't I Make This Years Ago!!!!

#7

Re: Why Didn't I Make This Years Ago!!!!

Todd Nebel

I use my tablesaw sled about 90% of the time for cross cutting.

Re: Why Didn't I Make This Years Ago!!!!

#8

Next jig should be .....

Jesse Cloud

same principle but put a 45 degree fence on both sides of the blade. Hard to get exactly 45 degrees, but easy to get two that add up to 90. Perfect miters from now on!!

Re: Why Didn't I Make This Years Ago!!!!

#9

A few suggestions for the next time.

Keith Newton----Little Rock, Arkansas

I have made many of them over the years, and my favorite size, is with a half sheet of 1/2" baltic birch. 30 x 60", even for a small saw.

Back when I was building cabinets on the jobsite in new homes, I was using a 9" Rockwell contractor saw. I would start by ripping my 4 x 8 sheets down to 2 x 8 for the base sides. From a 5' sheet of BB, there is 30" on each side of the blade, so when I would cut a 3' base cabinet side, that would leave 5' on one side of the blade, which would be supported out to its middle, so just a small downward pressure would keep it balanced.

I also like to use a taller fence, because eventually, you will need to use it to cut something really thick. Once you have cut through with the blade all the way up, there won't be enough wood left above the kerf to be very stout for holding both halves together when moving it around the shop storing it, when it is not on the saw.

Re: Why Didn't I Make This Years Ago!!!!

#10

Re: Why Didn't I Make This Years Ago!!!!

Brint in Richmond, VA

Yeah - what Bob S. said! Your write-up really motivates me to make one of these, which has been on my to-do list for ages.... Thanks!