Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

System Three Clear Coat Epoxy

Posts

System Three Clear Coat Epoxy

#1

System Three Clear Coat Epoxy

Dave Winters

I'm spraying with multiple coats of Zinsser's Seal Coat, then brushing on the Clear Coat, and I'm getting all these bubbles. Gotta be from the wood, doesn't it?? What would be a better sealer? I have some Vinyl Sealer from McFaddens, would that be good under epoxy??

Thanks!

-Dave

Re: System Three Clear Coat Epoxy

#2

Re: System Three Clear Coat Epoxy

Justin Szeliga

If the epoxy gets too hot it will bubble & boil. Are you mixing it correctly, or are you heating it to speed the cure?

Re: System Three Clear Coat Epoxy

#3

Jesper, Denmark

Re: System Three Clear Coat Epoxy

Jesper, Denmark

Epoxy as a clearcoat is not so good, as it is UV light sensitive and will eventually break down and get yellowish.

Re: System Three Clear Coat Epoxy

#4

Re: System Three Clear Coat Epoxy

Mark Mandell - Gone Round In Jersey

The bubbles are (usually) from the mixing, even using a gentle stir. You can deal with the problem is several ways.

One, you can thin the resin with some denatured alcohol (not more that 15% by volume) to reduce the surface tension of the liquid and make it easier for the bobbles to migrate to the top and "pop".

Second, you can pass a gentle flame (or heat gun) at a low angle over the wet surface to slightly warm it. This will draw the bubbles to the top and make them open.

Third, moving slowly, you can "spear" the bubbles with a tooth pick.

Lastly, if you're set up for it, after you mix the resin, cap the container and hook up a vacuum pump. A few minutes of high vacuum will draw most all of the bubbles out of the mix, then pour the resin onto the surface and tilt, do not brush, to spread it. Alternative on the vacuum is to put the coated item in a vacuum chamber, but I rather doubt you've got one of those kicking around the shop. ;)

Re: System Three Clear Coat Epoxy

#5

Re: System Three Clear Coat Epoxy

Dave Winters

Thanks for the replies. I don't think it's from mixing. I've tried both the heat gun trick and the popping with a pick.

I set up a hot box with a light bulb to speed the cure, and so maybe that's it.

I'm making longboard skateboard decks, and I'm trying to come up with a gloss, high build finish that doesn't take ten coats per board to get there. Any ideas for something more UV favorable?

Thanks!

Dave

Re: System Three Clear Coat Epoxy

#6

Re: System Three Clear Coat Epoxy

Merle

Might be spraying it on too thick so the surface dries before the bubbles can migrate to the surface.

Re: System Three Clear Coat Epoxy

#7

Re: System Three Clear Coat Epoxy

Dave Winters

I'm brushing the Clear Coat, but that's a thought (that I'm brushing it on too thick)

I'm getting all the (visible) bubbles out with a little dental pick, and then these huge bubbles appear. I'm at elevation 8,000 ft. I was wondering if that could be it....

Re: System Three Clear Coat Epoxy

#8

Re: System Three Clear Coat Epoxy *LINK*

Robin Corell in Atascadero CA

I used to just thin the epoxy and use that to seal the wood. it would usually take three coats to seal and build a high gloss finish. I never had major bubble problems that a heat gun or just a bit of compressed air at an low angle wouldn't take care of. I would suspect an off gassing issue with your sealr and the epoxy.

As for the UV issue I would sugest contacting a sales rep from BJB Enterprises. They make a huge selection of resins and other neat stuff. their sales reps are so knowlegable that you tell tham exactly what you want and they will have a product that fits the bill. I have always had exclellent sevice from them, they treat small one man shops the same as large customers.


http://www.bjbenterprises.com/

Re: System Three Clear Coat Epoxy

#9

Re: System Three Clear Coat Epoxy

Steve Schoene

A bunch of answers, but what is the application? That is what are you coating and how will it be used?

Re: System Three Clear Coat Epoxy

#10

Re: System Three Clear Coat Epoxy

Dave Winters

I'm making longboard skateboard decks. So, ideally, the finish will be a high gloss protective finish that will live outdoors mostly. And to keep my price point affordable, I don't want to have to spray a million coats to get there...

Re: System Three Clear Coat Epoxy

#11

Re: System Three Clear Coat Epoxy

Steve Schoene

Outdoors is a problem--or rather sunlight is a problem. Epoxy has poor resistance to UV light and won't last long unless protected by a finish, such as a marine spar varnish, that does resist UV, and even that will require maintenance with some regularity.

Re: System Three Clear Coat Epoxy

#12

Re: System Three Clear Coat Epoxy

Howard Acheson

I suggest you contact System Three. They have a good technical department and should be able to give you some good advice.

Re: System Three Clear Coat Epoxy

#13

Sorry I am so late getting here.

Keith Newton----Little Rock, Arkansas

You are right the bubbles come from the hot box. If the wood heats after the epoxy goes on, the air in the wood expands, causing the bubbles.

You should heat the wood up before applying the epoxy, then let it naturally cool, which will cause a negative pressure inside the wood. If you use an open porous wood, it will draw the epoxy in, so filling the grain first is a good idea.

As for the UV for your purpose, I would not worry about that here, since the amount of time spent in the Sun while in use, is not enough to worry about. Unlike boat trim, or and entry door, which is exposed daily.

Re: System Three Clear Coat Epoxy

#14

Update..

Dave Winters

Kieth, thanks.

That's what I'm doing now, using the hot box to heat the piece before finishing, and then after it's gone off to post cure. Working much better.

I'm using figured woods, and so I get uneven absorption on the first coat. So I flow the Clear Coat on and let it set 45 mins or so and then scrape all off with a plastic squeegee.

I'll post some picks later.

Thanks, all.