We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
Just saw a maple log on the side of the road that was being taken out for some road work. The tree was a double or two stem tree and the log was joined for about ten feet and then branched into two stems or logs. What are the chances the doubled part of it has the flame figure that a crotch or brand union has? Is it worth trying to snag the log and have it sawed?
Have the lumber sawn parallel with the forks, best chance to capture some "bonded grain" patterns. Get on sticks quickly, white maple is bad to stain/discolor with temps above 50*F.
You also want to have a metal detector handy. Haven't snagged a roadside tree yet that didn't have something nailed to it over the years. If you can, spray-paint a stripe on the side that faced to road as that will have been the billboard and it's opposite would be where the farmer nailed on his barbed wire. Anything over 5' about the ground "should" however, be clear.
You may, after all, have some difficulty getting a sawyer to take it because of possible saw damage from the hidden hardware.
I just read an article about judging crotch figure from the outside. This guys advice was to look at the bark at the top of the crotch. If the bark seems to form a radius between the two forks, the grain is probably knitted. If the bark appears to go into the joint, the opposite is occurring. You will find bark inclusions. But nothing is 100% in nature. That's all the fun of cutting it open. Maybe you could put it back on the edge of the road if it's not great!
I rode back up there and talked to them. The log I saw was much bigger than I expected, close to three feet on the stump. As I drove by, I thought it was about two feet. The guys cutting the wood told me that they thought it had some rot in it down low so it was laying in the edge of the burn pile. I am going to try to rescue the part above the rot. I could not see any rot, it must have been laying face down on it.
There were some other logs there they were selling. I'm going to buy several. Poplar and soft maple to use as "white" wood. I am scrambling to get them before they haul them away. $40 a thousand is Ok, don't you think.
Barry you offered to help me on a project once and I'd be glad to saw that log for you if you want to bring it to Tennessee... just kidding of course.
But seriously, if you need help finding someone in your area with a portable band saw mill let me know. I have a Wood-mizer and they keep a list of all their saw owners. I'd have to find the list tonight. On a log worth fooling with I don't worry too much about the metal. All that is at risk is a $20 (max) band.
Chuck, I have tried a number of times to find someone with a portable mill. Went to the Wood-Miser site and down loaded the list. Called everybody. Answers ranged from a wife telling me "Yeah, I think that thing is sitting out there in the woods behind the barn" to I don't have no bands, but if you would buy me a couple I would saw "er up fer ya". The problem then and now is moving the logs to the mill. I tried before to get a guy with a roll back wrecker to move some, but when he found out it was logs and not a car, he bailed, claiming a conflict with his insurance. No sense of adventure. My friend has an old truck, but he is fifty miles away. A guy did some sawing for me on the farm and he had the truck and mill, but he is sixty miles away. This is a logistics problem.
No, I don't think that $40 for whatever is good. After all is said and done it will probably cost double what it would if you bought retail, unless you believe that yours and your friends' time and effort has no value.
Your description sounds like a waste of time to me. It will most likely be captive bark. The work involved for you will likely just result in some very expensive plain maple.
With a mill out in my yard, and a tractor to handle the log and lumber, I would likely pass on this. But it's your call.