Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This $39 jig will make you a WOODWORKING GOD!

Keeping steel pipe clamps from staining work?

Posts

Keeping steel pipe clamps from staining work?

#1

Keeping steel pipe clamps from staining work?

Barry Irby

I made pads for my bar clamps out of 1/2" baltic birch plywood. Pretty happy with that. Made them "uniform" so they all sit a the same height. While working on them, I cleaned the old glue off the pipes. Most of the pipe is black iron and if it touches the work in a puddle of glue it leaves a black stain. How can I keep the bare steel from staining the work? I heavily waxed a couple of them, but that did not seem to work as well as I hoped.

So, how do you keep the iron from staining? And how do you make it easy to get the glue off the pipe?

Re: Keeping steel pipe clamps from staining work?

#2

Re: Keeping steel pipe clamps from staining work?

Howard Acheson

Buy some plastic shower curtain rod covers at a home center. They are split down the center so they slip over 3/4" pipe perfectly. Cut them into 4-6" lengths and slide them up and down the pipe so they are positioned at the glue joints. They will prevent the black staining. They can be easily cleaned as the glue will not stick to them well. You can make them easier to clean by applying a coat of paste wax before you cut them to length.

They will fit nicely over Bessies and Jorgies too.

Re: Keeping steel pipe clamps from staining work?

#3

Re: Keeping steel pipe clamps from staining work?

del schisler

get rid of the black pipe. and get galvanize and that will take care of the problum.

Re: Keeping steel pipe clamps from staining work?

#4

Dale Lenz

Re: Keeping steel pipe clamps from staining work?

Dale Lenz

It has been my experience that the black marks are somewhat superficial, gives me a reason to use one of my hand planes.

Re: Keeping steel pipe clamps from staining work?

#5

Re: galvanized

McKay

The galvanized pipe will allow the cauls to dig in too much so stick with the black. When clamping, snug one clamp on the bottom...the second clamp should be on top of the panel being glued and can be positioned above the wood by about 1/2". Continue to clamp with the clamps positioned about 1/2" above or below the panel. Return to the original clamp, loosen, and re-tighten. This also positions the clamping pressure to be more centered on the edge of the wood instead of just at the top edge of the wood. (If you look at the canted angle of the jorgensen pony clamp, you will notice that by raising up the panel being glued that the pressure will be better centered on the edge of the wood.) Once a month prepare a solution of vinegar and wipe the black pipe. This will dislodge some of the glue that builds on the pipe and make the clamps easier to slide along the length of the pipe.

Re: Keeping steel pipe clamps from staining work?

#6

Re: Keeping steel pipe clamps from staining work?

Nicholas Tuzzolino

I run a strip of clear packing tape down the pipe.

Re: Keeping steel pipe clamps from staining work?

#7

Re: Keeping steel pipe clamps from staining work?

Dave's Not Here

Lay some wax paper between the clamp and the wood.

Re: Keeping steel pipe clamps from staining work?

#8

That's A Good Idea..........

Dave's Not Here

Re: Keeping steel pipe clamps from staining work?

#9

Re: Keeping steel pipe clamps from staining work?

George, Oxford, NC

Sections of PVC work also.

George

Re: Keeping steel pipe clamps from staining work?

#10

Re: galvanized

Barry Irby

I have a few that are on galvanized pipe. I find the galvanizing to be too soft and the clamps really dig in, creating sharp edges on the pipes. If I find a really pronounced one that's too sharp, I file it off.

I also find some pipe to be too small. I had someone give me about twenty pieces of pipe in handy lengths. Thought I was set for life. It was threaded even. Turned out to be made in China and really crappy. Would barely grip and when it did , you could put the threaded section right off.

Re: Keeping steel pipe clamps from staining work?

#11

Hand Planes......

Barry Irby

Great! An excuse to buy a new tool. I was eye balling the new Wood River Planes last night. I am not into planes and have not used one in years, but I feel like there is one pursuing me. I have a No.4 (?) that's been in a drawer for forty years. Might be time to get it out and try it. Wonder what its for?

Re: Keeping steel pipe clamps from staining work?

#12

Re: Keeping steel pipe clamps from staining work?

Barry Irby

I'll try that. I ran a strip of blue tape on the top side of mine. It really sticks to the pipe if you leave it on there. It got chewed up. Had to scrap it off. Almost as much trouble as the glue, but it did keep the black off the work.

Re: Keeping steel pipe clamps from staining work?

#13

Re: Keeping steel pipe clamps from staining work?

Larry in NW OHIO

Barry It`s a little more work, but not very hard work. Like Dave said get some wax paper and cut them into strips about 2" wide and lay it under the clamp and position it where you want it and snug it up a little and go to the next one and so on then go back and thighten them. After a few time you`ll get your own way to do it. Best of luck. Larry

Re: Keeping steel pipe clamps from staining work?

#14

In general....

Barry Irby

Some people put covers on the pipes, either PVC or shower curtain rod covers. I like that and may do it, but it requires getting and preparing the covers either as a bunch of short pieces or in various lengths and then storing the covers in between uses.

Then there is tape and wax paper. That means that at the end of the glue up you have to ball them up and throw them away.

I like the idea of the spaces. Slightly tedious, but nothing to clean up and store. How about a spacer made of something the glue won't stick too and magnetic or with little clamps that hold it in place? You just need to do one or two clamps.

Actually, what I was visualizing was something like a spray coat of shellac (?) or lacquer (?) on the pipes to make it easier to remove the glue and to keep the black off the work. Its always in place, nothing to throw away, nothing to keep up with, etc.

Thanks for the thoughts. Definitely got me outside my box

Re: Keeping steel pipe clamps from staining work?

#15

I use spacers...

John in NM

All those little 1/4" x 3/4" strips that come with every project get cut into 6" or so lengths and put in a coffee can. I put them on the glue up and then put the clamp on top, two for each clamp. They also make handy epoxy mixers. One shop I worked for did a lot of mesquite work, so we never had enough mixing sticks around. At one point one of my jobs was to convert scraps into mixing sticks :D the habit seems to have stuck

Re: Keeping steel pipe clamps from staining work?

#16

Re: In general.... *LINK*

pecker

How about a spacer made of something the glue won't stick too and magnetic

Maybe those flexible magnetic sheets would work.


img

http://www.dickblick.com/products/flexible-magneti

Re: Keeping steel pipe clamps from staining work?

#17

Explanation of what is going on....

Bill Tindall

Water and perhaps other components in the glue are corroding(dissolving) the iron. Soluble iron will react with the tannin in wood to make a blue/black colored pigment or dye(I don't know which).

I eliminate the problem by laying news paper over the clamps, or, I use my aluminum bar clamps.

I don't recommend buying pipe clamps. They are annoying to adjust and worse, they flex when tightened to the pressure required for PVA glue. Steel I-beam clamps or aluminum channel clamps are best.

Re: Keeping steel pipe clamps from staining work?

#18

Re: Explanation of what is going on....

Barry Irby

I understand that some sort of chemistry is going on between the steel in the pipe and the glue and the wood. That's why I was hoping wax would work well enough to break the contact. No silicon, it would get into finishes. Maybe shellac.

I also understand it would be better to have better clamps. Just can't afford to start a whole new collection.

Maybe I should start by getting about four. There's always Christmas, and next Christmas.

Re: Keeping steel pipe clamps from staining work?

#19

Re: Explanation of what is going on....

Carol Reed, Strawberry, AZ

Get 5 clamps, Barry. One for the middle and an even number on either side of the middle. At least that's how I seem to use clamps.

I like the aluminum Universal clamps by the Dubuque Clamp Co. They are strong but light weight. No staining issues. Less expensive than Bessys. I have them in sizes from 24" to 6 feet. The trick is to keep acquiring them, a few at a time.

FWIW.

Re: Keeping steel pipe clamps from staining work?

#20

pipe clamps

del schisler

seam's like a good fix would be to just change out the black pipe for galavanize pipe. If you getting black marks. Their you need to use a work around ? I have use gal. pipe for 30 to 40 yrs. I don't remember any staining. my 2 cent's

Re: Keeping steel pipe clamps from staining work?

#21

Oh Yes! these are the clamps

Bill Tindall

These are the Cadillac clamps. You can order them from the factory in lots of 10 and save a pile of money. Our club has bought stacks of them for members. Wholesale they are little more than a pipe clamp.

Their inventor, a chap from CA, told me they tightened them in the furniture factories with air wrenches.

Re: Keeping steel pipe clamps from staining work?

#22

Re: In general....

AZ in Colorado Springs

I use the wax paper method. But, don't throw it away. Roll it up or fold it up for storage and use it again and again ... . If a big glob of glue gets on it, flick it off with a fingernail. It'll last a long time. ;)

Re: Keeping steel pipe clamps from staining work?

#23

I don't know Bill...

John in NM

Usually I agree with you, but I don't think I'd recommend anyone abandon their pipe clamps just because of a little staining :D

Good advice though for those who find them a pain to work with for other reasons.

I like pipe clamps because they're cheap and easy to use, flexing can be countered by alternating sides or putting blocks under the bars (or best yet, both), and the staining can be dealt with by any one of the suggestions in this thread - including Del's of using galvanized pipes. I have two that are on galvanized pipe and they do work fine, I've found the "too soft" thing to be a bit of a red herring repeated all over the net and in every book on the shelf. In practice it makes little difference though.

I also like that you only need 18", 36", and 48" pipes and a box of unions and you can make up a bunch of useful sizes without having dedicated clamps for each length taking up space and disposable income.

All that said, I trust you won't take it as a criticism for choosing nicer clamps - good stuff is a real pleasure to use. I once bought 10 5x18 Wetzlers for a laminating job, and now I can't go back to lighter bar clamps :D I recently managed to break one of them, a feat I did not think possible (at least not before I grossly abused the clamp using it in tensioning fence!)