Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Router bit slipping

Posts

Router bit slipping

#1

Router bit slipping

JoeW in Detroit, MI

I have a 1/4-inch straight router that keeps slipping in my router. The router is a Bosch 1671. I've cleaned the collet and tightened it as much as possible. The bit shaft has a couple of small wear marks, but no burrs or other damage I can feel by hand. Is it time for a new bit or is there something I'm possibly missing.

Re: Router bit slipping

#2

Re: Router bit slipping

FredD

If you have no success in tightening the bit drop a 3/16ths or 1/4 inch dowel the right length ahead of the bit so the bit bottoms out where you want it and it can't slip further.

FredD

Re: Router bit slipping

#3

Re: Router bit slipping

Robin Corell in Atascadero CA

Some routers require a bit of space between the bottom of the collet and the end of the router bit. in practical terms this means that if you place the bit in the collet until it bottoms out and then tighten it you are likely to have problems with the bit slipping. the fix is to drop the bit all the way in and then pull it our 1/8" before you tighten the collet.

Robin

Re: Router bit slipping

#4

Re: Router bit slipping

Warren E. White

I have experienced the same thing, especially when routing hard woods. I have tightened the collet until I was about to bust a gut; still slipped. Pulled the bit up a bit and tightened again; still slipped.

Got fed up with the amount of chatter on a 1/4" shank and bought a 1/2" shank bit. No slipping.

Either the bit was a bit dull or I was just asking too much of it.

WW

Re: Router bit slipping

#5

Dale Lenz

Re: Router bit slipping

Dale Lenz

Back in the early 90's FWW had an article over cleaning the router collet. Can't recall the fine details but one thing I recall and used is using a pencil eraser to rub the inside of the collet with, has worked for me several times when my bit has slipped.

Good luck

Re: Router bit slipping

#6

Re: Router bit slipping

Myra Fox

It is possible that the shaft of the bit is slightly undersized. Put a caliper on it. IIRC, it should not be less than .248 inches.

Re: Router bit slipping

#7

Re: Router bit slipping

del schisler

It is probly not a true 1/4" bit or maybe you have the 3/8" collet on ?? I didn't read the other post's yet I have the same router and no problum's with any bit's. Have you got any other 1/4" bit's to try? This may be a off brand bit ? Don't use it or tell you find the reason. I have 5 router's and use most every day . good luck

Re: Router bit slipping

#8

Worn out collet?

Jorge Casta�eda

Collets don't last forever, maybe it is time for a new one.

Re: Router bit slipping

#9

Re: Worn out collet?

JoeW in Detroit, MI

I hope not. The router does'nt have that much use on it. Frustrating things is, used the same router, same bit, on the same type of wood (mahagony ply) last week withe no problems. I don't normally set the bit at the bottom of the collet. I need to measure the bit diameter, and try another bit as suggested. I guess if these fail, I will by another collet. Hate to buy a 1/4-inch collet as I am slowly buying 1/2-inch as needed. Thanks to everybody for the ideas for the ideas.

Re: Router bit slipping

#10

Re: Worn out collet?

andrew nistock

Don't be too quick to blame the collet. Had a similar problem with my shaper a few years back. Bought a cheap 1/2 inch shank router bit to make a short run of moulding for the porch windows and the bit would not stay put in the shaper collet. Measured the shank close to the cutter and at the tip of the shank and there was .005 difference. lesson learned. Buy only good grade american made bits. You get what you paid for. Andy

Re: Router bit slipping

#11

Bit Jack Hammering Effect

charlie belden

If you bottom out the bit - impact from the cutting jack hammers the bottom of the bit into the bottom of the chuck hole - alternating up and down forces.

On split collets with just three or four "slits' gunk in the slits can effect the grip as well.

Pull the collet and go at it with a fine toothbrush - and pin if necessary. A Qtip & alcohol to clean the inside of the sleeve the collet fits in amd wipe the bit shank with alcohol on a rag.