Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

WC Weekend Accomplishments...

Posts

WC Weekend Accomplishments...

#1

WC Weekend Accomplishments...

Dennis E Peacock

30 Aug 2010

Good Morning Everyone,

Well, I've got some cleaning done in the shop, got some wood put up so I can better find the floor in my shop and my boys were kind enough to help get the area around the lathe cleaned up for me.

It's been easier to get some stuff done since the weather has turned a bit cooler. I've still got to split and put up the last bit of firewood I have stacked in my yard, it should be good and dry though since it's been stacked there a year now.

I find it amazing just how much time goes by when your lives are disrupted by critical life situations with ones own kids and cancer battles with you own parent(s). I don't mean this in a bad way, it's just that you wonder, pray, and work to do all you can do and then you find out just how much control you do "not" have over your own life. But...this alone is a book all on it's own.

I still have my daughter's hope chest to get started and finished and I'm hoping to make a few cutting boards this year as well. I guess we shall see just how much I can or can not get done due to circumstances in life and the call of work at the day job.

Well, enough crying on your shoulders....what did YOU do this past weekend?

Best of weeks to you all.

Dennis Peacock

Re: WC Weekend Accomplishments...

#2

Re: WC Weekend Accomplishments...

Larry in NW OHIO

Good morning Dennis and everyone. Don`t feel bad when you need schoulders to lean or cry on, you have a lot of them here to do it on. I include you and a few others here in my prayers. The best to you and your family. I didn`t get to much done "in the shop", because my son needed some help wiring his new patio, so I did that on Sat. and on Sunday I was able to do a little in the shop making Christmas presents. Finishing off two Chival mirrores, one for the church fall festival and one for a wedding present for one of my God children. Then a little time working on 6 mail truck banks for my grandchildren. That`s it for me. I hope everyone did OK. Larry

Re: WC Weekend Accomplishments...

#3

Completed Last Three Chess Boards

George Colonel's Workshop-Havertown PA

Happy Monday Dennis,

I got them done about the time I ran out of sapele! Took them outside to sand and have since appliied the first two coats of naptha/poly mix. they are looking good, and the figure of the maple pops out dramatically. Yesterday afternoon I resawed enough maple to form the three cabinets and drawers the boards will sit upon. Today I plane them all to 3/8", cut to length, and set up the P+C box joint jig. Its going to be a busy flat work week. Last night we had our party,

#3 son Ken BBQ'd and #6 son Jon and #3 daughter Mary helped eat it. We had a great time, and enough beer to keep us cool.

Have a great week, Dennis.

George

Re: WC Weekend Accomplishments...

#4

finished tractor shed

Thomas S Stockton

I put the roof on my tractor shed, wanted to do it Saturday but it rained all morning and we went to a party in the afternoon.

I really enjoy projects like this I drew up no plans just went out and measured the tractor and came up with a rough size. I then went and looked at what kind of beams we had laying around and went from there. One of the funnest parts is doing all the joinery with a chainsaw which can actually be a pretty accurate tool although I'm going to have to clean it pretty well to get the creosote off of it.

Tom

Re: WC Weekend Accomplishments...

#5

Re: finished tractor shed

Joseph Bradshaw

Thomas, your tractor shed looks good. I built one similar to it a few years ago. I found that water will run down on the inside of the roofing tin. You will need to box it in someway. I put a short extension on mine, sort of like a cape cod style.

Re: WC Weekend Accomplishments...

#6

Dale Lenz

Re: WC Weekend Accomplishments...

Dale Lenz

We had a taste of fall for a few days, but the warm muggies days of summer have returned the past two days.

Waterbed decided to leak, so yesterday drain the bed, mattress is wave less, fiber filled, some kind of heavy "empty�. Broke my wheel barrow's handle taking the old mattress outside, will be looking for some 2" oak to replace the handles, at least I get to do some woodworking. While the waterbed was empty decided to put a ceiling fan over the waterbed, needed the trouble light to see while installing the fan, trouble-light broke, why is it some jobs take all day and then some, : ' >.

Re: WC Weekend Accomplishments...

#7

Dale Lenz

Failed to mention

Dale Lenz

Central AC went out Thursday. At least it was relatively cool. Still waiting on the bill, 4K+, when it rains it pours. Speaking of rain we sure could use some.

Re: WC Weekend Accomplishments...

#8

Re: finished tractor shed

Larry in NW OHIO

Tom You better call the Sheriff, because someone stole the four sides on your "finished" shed. Larry :D :D

Re: WC Weekend Accomplishments...

#9

Re: finished tractor shed

Barry Irby

Tom, Like Joseph, I see a couple of things that bother me. I grew up on a farm and we had several sheds.So, if you don't want unsolicited suggestions, stop reading here.

Joseph is right, water will drool down from the top edge. You need to form a "drip edge" along that edge of the tin. The easiest way might be to turn about a half inch lip on the tin downward well past horizontal. It would take an hour or so, but you could do it with a pair of sheet metal workers tongs. (Pliers shaped like a hammer head shark with jaws about four inches wide.) Just work you way back and forth and turn the edge over and over until you have it tipped down.

The ends of the rafters will get wet and may eventually rot. They do not have a plumb cut on them,. so the bottom sticks out further than the top. Water will also drool down them to the inside. Being a chainsaw surgeon now, you could plumb cut them now.

The ends of the beams on each side. They stick out far enough to get wet. They are creosoted, but I don't know how well. Might be wise to put a cap on them out of some rust resistant metal. shape the caps with a drip edge around them. Similar caps could be put on the plumb cuts on the rafters.

You also have the raking resistance relying on a single bolt in the angle braces. I am assuming there are no bolts I can't see and no fancy joinery. Might be wise to add a few.

It appears the posts are founded on top of block or concrete piers. They need to be anchored very securely to avoid the building lifting off in a heavy wind.

Re: WC Weekend Accomplishments...

#10

Jesper, Denmark

Re: New floor in loft over shop.....

Jesper, Denmark

This was not a single weekend project, but several times over the last month.


Some of you may remember a post concerning the size of cutters for T+G flooring about a month ago. The reason was this, that the boards were planed and had T+G in the sides, but not the ends. I ended up cutting the T+G in the ends with two different router set-ups.

The original floor was in terrible condition, 3/4" beadboards, full of powder post beetles and damaged from roof leaks many years before I bought the house. Once I got into the demolishin�n, I was realy surprised that no-one had fallen through. The problem was worsened, as the center spacing of the beam joists is around 40", which really needed 6/4 flooring - but the boards available from a Norwegian lumber yard ended up around 1 1/8" thick.

uplimg]/webbbs/media/temp/5d2cb1baa182729e0c4c11ea4b9a3fd3_2_vrkstedsloft004.jpg" />

The building, which is attached to the house, was originally built in 1928 as a beer distribution depot. It is full brick contruction to the loft floor and half brick augmn�nted with a opole barn structure. Originally, the posts supporting the ridge were carried all the way to the ground, but a previous owner installed a steel beam below the floor and removed the lower part of the posts. ALl the wooden structure is tapped and dowelled together in the fashion of the day. The wood is all locally grown pine and spruce, in whatever sizes might fit.


There aree a few details left to be finished, such as repairing windows in both ends - the North end windows are old cast iron barn windows and theSoth ones modern wood windows.

All in all , I expect there have been 100 hours invloved, including dem�lition and taking the old stuff to the dump. Total area is 1200 sq. ft.

Re: WC Weekend Accomplishments...

#11

Re: finished tractor shed

Thomas S Stockton

Thanks Barry and Joseph

Thanks for the advice it is fairly well anchored to the concrete footings so not to worried about blowing away and the beams are old school creosoted weigh a ton and were on the ground for about 20 years before I used them so they aren't going to rot.

Your ideas about cutting back the rafters and adding a drip edge are great thank you.

Tom

Re: WC Weekend Accomplishments...

#12

Jesper, That Looks Great!

George@Colonel's Workshop-Havertown PA

Re: WC Weekend Accomplishments...

#13

Finished table, and found an alligator nest..

Keith Newton----Little Rock, Arkansas

After finishing off a little table, I drove down to our cabin for the weekend with family.

After they all left Sunday afternoon, I went for a paddle in my canoe "Stealth". The creek is getting low, which reveals lots of things that are otherwise hidden.

I found another old wooden boat sunken on the bottom, from who knows how long ago.

Also, back in one of the backwood sloughs, I found an alligator nest. There was lots of signs of alligator activity around there, which I find very intriguing. I don't think they have hatched, or I would have seen some of them by now, so I am looking forward to the hatch.

Then, on the way back to the camp, just as it was getting dark, I spotted what I thought was a grasshopper flying out over the creek. It didn't make it to the tree which it was headed for, so it ended up in the water.

When I came alongside, I found it was a Mantid, so I pulled out my camera and started shooting as it did the breast stroke on toward the tree.

The situation was difficult to shoot, with me kneeling athwart-ship, hanging over the side with the camera, trying to keep up with its swimming, with a very long paddle. However, in the end, I got a couple of good images, with its wings spread, it looks more like it's flying than swimming.

Re: WC Weekend Accomplishments...

#14

Barb Siddiqui

Great floor project. Beautiful Loft!!

Barb Siddiqui