Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Dryer Clothes

Posts

Dryer Clothes

#1

Dryer Clothes

Larry in NW OHIO

My sons clothes dryer has about 25 foot of aluminum ridgid pipe on it going to the outside. Yes I know it`s to long, but it works and I need to get to it. Where can I get a booster fan and what does it need to be like. I assume it needs to be fitted to the same CFM or very close and how do you find out the cfm for the dryer. Or does it need to be even close? Does anyone else have the same problem and what did you do to it? Thank You Larry

Re: Dryer Clothes

#2

Re: Dryer Clothes

Galen Vetterick

I had about the same setup in a home for 15 year. I just made it a yearly habit of going outside and rod in a nylon brush set up like a chimmney sweep to clean out the lint that accumulated. I just tried to insure good flow.

Seems like any added fan would be subject to lint build up on the blades as no dryer is lint free. If you used too large of fan I could see drawing out the heat too fast and result in poor cloths drying.

That said I did replace the heating element once but cannot say it was vent length related or just a lot of use.

Re: Dryer Clothes

#3

Re: Dryer Clothes

Barry Irby

Larry, You are getting into dangerous territory. The same lent that clogs the duct would most likely collect on the fan blades and stop the fan. There are numerous dryer fires every year. A significant source of house fires. And that's without adding an additional fan that might be an ignition source. I would suggest you re-route the duct a shorter distance if possible. If that is not possible, see if you can improve it by Increasing the diameter to five or even six inches. Run the vent out of galvanized rigid metal, not plastic and not the flex stuff. A larger duct will slow the air flow down and may tend to accumulate crud faster. At least once or twice a year you should clean the vent. Google cleaning dryer vent or some thing along those lines. They make cleaning kits now, sort of like chimney cleaning brushes. Might be a good idea to check with the manufacturer of the dryer, also.

Re: Dryer Clothes

#4

Re: Dryer Clothes

Fred Davis

Larry , try this site , it will answer your questions, may be a little pricey, but then rerouting ducting can be also.

If your smooth Aluminum duct is in good condition , I would keep it rather then going to G.I. duct and rust down the line.

http://tjernlund.com/retail/dryerductbooster.htm?gclid=CIPx59_936MCFcHs7QodghVmrQ

FredD

Re: Dryer Clothes

#5

Re: Dryer Clothes

ThomD

It would be cool if in addition to the dryer fan there was a small cyclonic separator that would keep the lint in a bypass area where it would be cool and easily recovered.

Re: Dryer Clothes

#6

Re: Dryer Clothes

Barry Irby

That's something! I had not seen one of those and will file it away for the next person that needs it. OTOH, at almost $300 I wont be the first kid on my block to get one.

I agree with Fred. If you have good aluminum ducting don't replace it with galvanized Iron. But It should be sheet metal filled ducting, not aluminum foil, and preferably not the slinky or stretch tube stuff. You want tough, smooth ducting that can be cleaned without being destroyed, that will resist rust (Al. being better than GI here because of the chemicals in dryer vented air and moisture) and heavy gauge enough to contain a lint fire if one occurs. ln other words good corrosion resistant sturdy ducting, not an afterthought.

Re: Dryer Clothes

#7

Got a leaf blower? *LINK*

Tim Greif - West of Chicago

I had a similar situation a few years ago with a vent about as long as yours. Leaf blower to the rescue. Actually, although the story is pretty funny, it did significantly improve the dryer performance. Do it regularly.


Dryer Vent Story

Re: Dryer Clothes

#8

Re: Got a leaf blower?

Larry in NW OHIO

Tim Belive it or not we have the same setup as you, about 25' and 4 90degree elbows, and I still remember reading that post as soon as you mentioned it. But I can`t believe it`s been exactly 6 years to the day tomorrow, how that for coincidents. I think I`ll try that, I even have an Electric Toro leaf blower, but I`ll take the louvers off outside before I start it up and I`ll have it on very slow and go slowly upward. Thanks for the warning Larry

Re: Dryer Clothes

#9

Re: Dryer Clothes chart

john b

Brand Vent

Material Hood

Type Maximum Vent Length

with 90� elbows

0

elbows 1

elbow 2

elbows 3

elbows 4

elbows

Amana

Speed Queen

(domestic) Rigid

Metal A 44 ft. 34 ft. 26 ft. 20 ft. 14 ft.

B 34 ft. 26 ft. 20 ft. 14 ft. 8 ft.

Semirigid

Metal A 24 ft. 20 ft. 16 ft. 12 ft. -

B 20 ft. 16 ft. 12 ft. 8 ft. -

Frigidaire

White Westinghouse Tappan, Gibson Rigid

Metal A 60 ft. 52 ft. 44 ft. 32 ft. 28 ft.

B 48 ft. 40 ft. 32 ft. 24 ft. 16 ft.

Flexible

Metal A 30 ft. 22 ft. 14 ft. - -

B 18 ft. 14 ft. 10 ft. - -

GE

(6.0+ capacity

electric models) Rigid

Metal A 90 ft. 60 ft. 45 ft. 35 ft. 25 ft.

B 60 ft. 45 ft. 35 ft. 25 ft. 15 ft.

Flexible

Metal A 55 ft. 40 ft. 30 ft. 20 ft. 15 ft.

B 45 ft. 30 ft. 20 ft. 15 ft. 10 ft.

GE

(5.7 capacity

gas & electric) Rigid

Metal A 60ft. 52 ft. 44 ft. 32 ft. 28 ft.

B 48 ft. 40 ft. 32 ft. 24 ft. 16.ft.

Flexible

Metal A 30 ft. 22 ft. 14 ft. - -

B 18 ft. 14 ft. 10 ft. - -

GE

(6.0+ capacity

gas models) Rigid

Metal A 45 ft. 35 ft. 25 ft. 15 ft. -

B 30 ft. 20 ft. 10 ft. - -

Flexible

Metal A 30 ft. 20 ft. 10 ft. - -

B 15 ft. 10 ft. - - -

Camco

GE, Moffat, McClary Rigid

Metal A 45 ft. 35 ft. 25 ft. - -

B 30 ft. 20 ft. 10 ft. - -

Flexible

Metal A 30 ft. 20 ft. 10 ft. - -

B 15 ft. 10 ft. - - -

Magic Chef

Admiral, Norge Rigid

Metal A 45 ft. 35 ft. 25 ft. - -

B 30 ft. 20 ft. 10 ft. - -

Maytag

MDE... models Rigid

Metal A 65 ft. 54 ft. 44 ft. 36 ft. 28 ft.

B 59 ft. 48 ft. 38 ft. 30 ft. 22 ft.

Flexible

Metal A 36 ft. 32 ft. 28 ft. 25 ft. 23 ft.

B 28 ft. 24 ft. 20 ft. 17 ft. 15 ft.

Whirlpool

KitchenAid, Roper Rigid

Metal A 64 ft. 54 ft. 44 ft. 35 ft. 27 ft.

B 58 ft. 48 ft. 38 ft. 29 ft. 21 ft.

Flexible

Metal A 36 ft. 31 ft. 27 ft. 25 ft. 23 ft.

B 28 ft. 23 ft. 19 ft. 17 ft. 15 ft.

Re: Dryer Clothes

#10

Re: Dryer Clothes

Mickey Elam

Try this:

http://residential.fantech.net/residential-products/laundry/dryer-booster-fans/

I would ensure that there is access for cleaning the duct and fan at least annually. I've had one of these and it worked great. Clothes got dryer, faster, and there was no more condensation in the vent tubing. It had an automatic switch that worked either via humidistat or air movement to turn it on and it stayed on after the dryer cycle completed for about 10 minutes to ensure there was no moisture or lint remaining in the duct.

It was a great addition to the system and I'm thinking about adding one to my current house.

Re: Dryer Clothes

#11

Re: Dryer Clothes

Larry in NW OHIO

Mickey Thanks, this along with a couple others from the other posters, look very good and interesting. I have them marked and want to go over them better when I have time. Thanks again everyone. Larry

Re: Dryer Clothes

#12

Re: Got a leaf blower?

FredD

Larry , you didn't mention 4 nineties on your first post.

Each ninety degree elbow in a run is equivalent to 5 feet of ducting , friction wise , so your son really has 45 feet of duct for all practical purposes.

He might seriously consider rerouting the duct with less nineties , befofe he springs for a fan.

FredD

Re: Dryer Clothes

#13

Re: Got a leaf blower?

Larry in NW OHIO

Thanks Fred I really did know that from my dust collection days and reading Bill Penz web site. I just don`t know how else to do it without going through the block foundation. The next time I get down there I want to look at it closer and see if I can make a straighter run, instead of going at such an angle, but then I would be getting into alot of elec. and plumbing. But it`ll be worth a try. Thanks for all the suggestions everyone. Larry