Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

New dust collector

Posts

New dust collector

#1

New dust collector

Stephen Kirk

I just picked up a new (to me) Jet DC 1100 with canister filter and remote. Lightly used and less than half the new price. I had recently added a Dust Deputy to my shop vac which I don't think will work too well with the bigger machine. I think I'll add a trash can pre-separator to extend the life of the filter. Hopefully, I can finally get a good airflow for my jointer and planer now- the shop vac worked, barely, but I was often clearing clogs, getting some blowback, etc.

Anyone else have experience with the trash can pre-separators? I know Oneida has a bigger Deputy but it would cost more than my DC did. The trash can versions are a mere 20$.

Re: New dust collector

#2

Re: New dust collectir

Neal in San Jose

I have that same unit, and am not really all that impressed with it. The filter clogs far too quickly. I ran across a Magnehelic gage on the scrap pile at work(vacuum gage for use in HVAC) and installed it in my ducting so I can keep a close eye on when the dust has clogged the filter. When I'm using the wide drum sander, I can watch the vacuum drop!

I use a trash can seperator when I'm using my planer, but don't bother using it with any other tools. The seperator does help keep the lower bag from filling up so quickly, and that's a good thing because it's a nuisance to change, but it doesn't seem to collect much on other tools, so I don't bother any more.

If you figure out a good, effective, easy way to clean out the cartridge, a lot of us would like to hear about it. I've tried compressed air, rolling it around in the back yard, all sorts of things, but don't have any method that works all that much better than the little flippers. Oh, I can't recommend the back yard method unless you have REALLY understanding neighbors.

Re: New dust collector

#3

Re: New dust collector

Robert R. Clough - Thorncraft

Stephen. I have the Oneida Separator, I connect it to an older Rigid vacuum which is part of a clear plastic tubing system for my shop. (It is a small shop and I use a gate for each tool.) So far the Oneida has worked well. It captures probably 95% of both chips and dust - I have not had to empty the vacuum for several months.

Re: New dust collector

#4

Re: New dust collector

Brian George

Steve,

I have been thinking about a separator and found this thread about the "Thein separator." Here is a link for you to do some reading about.

http://www.cgallery.com/smf/index.php

Re: New dust collector

#5

Re: New dust collector

George Koch

Stephen, I strongly agree with Brians suggestion. I've built 2 of Phil Thiens separators, one for my DC and one for my shop vac. They both work great at keeping 95% away from the filters/ bags. George

Re: New dust collector

#6

Re: New dust collector

Barry Irby

I converted a roll around RubberMaid trash can to a preseparator. I use it to pick of the debris form the a the and on the planer. I have a Delta DC with a top filter bag and trash bag at the bottom. The trash can does an excellent job of capturing the coarse stuff. Not sure about the fines. I really like it for piking up the lathe stuff, because those long stringy pieces will get caught in the Impeller and I have to reach in and clean them out. It is also easier to empty the trash can than the bag on my unit. If you are interested, I can take a picture of two later today and post them.

Re: New dust collector

#7

Re: New dust collector

Dave Bair, Eaton Rapids, MI

I have the 1100 with canister. I also use the trash-can separator from Lee Valley on my planer and jointer. (It keeps the collector bag from filling up too quickly and lets me gather fairly clean shavings for my neighbor to use for his rabbits). I have to open another dust port to keep the 1100 from sucking all the chips out of the trash can unless the filter is a little dirty. I just use the flappers and a little tapping on the filter to clean it. I am pleased with it's performance for the past two years.

Re: New dust collector

#8

Re: New dust collector

Glenn Madsen near San Francisco

My setup is very close to what Barry describes. I have a 6' thick felt bag on mine, but 10' of headroom in the garage. The simple drop can I rigged is a Rubbermaid, with a toilet plumbing fitting coming out the top, routed from some scrap subfloor plywood. The inlet drops in, and goes through a sweep 90*.

8 or ten dumpings of the trash can, minimum, before the Delta bag needs emptying. That is, if the operator watches the trash can level... ;)

Re: New dust collector

#9

trash can pre-separators

del schisler

the best thing i bought for a while Just empty the trash can Much easer than take the dam bag off I skin my knuckels every time Tell i woke up and used gloves trash can pre-separators is the way to go

Re: New dust collector

#10

Re: New dust collector

Dave Paine

I made a Trash can separator. Eventually discarded.

This was "only" a 40+ gal unit. It fills too fast and then the particles end up in the dust collector anyway. Also consumed a good amount of pressure drop.

Once I appreciated how much delta P and airflow it was consuming, and the quick fill up, I pushed it aside and have not used.

Cleaning the cannisters is NOT easy. The flippers are ineffective. I use just to knock down the big stuff.

I remove the cannister turn upside down and use a hand brush to knock down as much as I can. I suck this out with shop vac, since attempting to turn back right side up ends up with the particles getting re-stuck in the cannister cleats.

I finish off with the shop vac brush and finally compressed air. Takes about 15 - 30 mins depending on the day.