Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Bandsaw quit

Posts

Bandsaw quit

#1

karl jr

Bandsaw quit

karl jr

There I was, merrily cutting out turning blanks, and shut the (Laguna 14) bandsaw off. A minute or two later I tried to start it back up and... nothing. The little light on the switch box turns on but the motor doesn't run. I let it sit for a while to cool off (with fingers crossed) and tried again. No luck. I also tried restarting after turning the armature a bit, by rotating the lower wheel of the saw. No luck there either.

Can anyone around here tell me what else (and how) to check next?

Re: Bandsaw quit

#2

Jim DeLaney, Austintown, Ohio

Re: Bandsaw quit

Jim DeLaney, Austintown, Ohio

Possibly your magnetic switch.

Is power getting to the motor?

Does the motor hum, or just sit there?

If it hums, it might be the start capacitor.

Before you do much of anything else, though, I'd suggest calling Laguna.

Re: Bandsaw quit

#3

karl jr

Re: Bandsaw quit

karl jr

Power gets to the switch, so I assumed the motor gets power.

(Problem between switch and motor?)

Motor doesn't hum.

Thanks, I think you helped me narrow it down a bit. I guess a call to Laguna is in order.

Re: Bandsaw quit

#4

Commonly it's dust in the switch.

Phil Joines

Re: Bandsaw quit

#5

karl jr

Re: Commonly it's dust in the switch.

karl jr

Ney there, thanks. I give it a blast with the air.

Checked the voltages at two points in the switch box, with the assistance of a guy at Laguna. All's good there. While the cover was off I detected a buzz. Not coming from the motor, but somewhere in the switch box.

Re: Bandsaw quit

#6

karl jr

Re: Commonly it's dust in the switch.

karl jr

Gave it a good blow with the compressor while sucking with the vac. No luck. Guy at Laguna thinks it might be the switch box, but he hasn't called back yet. When I started talking to him I said the BS was a 14 SE. He replied, "Oh, the one-off." What's that all about?

At any rate, buying a switch box is certainly going to be less painful than buying a new motor. Less blood to squeeze out of the turnip, if you know what I mean :)

Re: Bandsaw quit

#7

karl jr

Re: Bandsaw quit

karl jr

There's a hum coming from the switch box, but not from the motor. The start capacitor is the cylindrical thing mounted to the motor, right? Where's the magnetic switch located?

Thanks for the help

KTK

Re: Bandsaw quit

#8

Re: Bandsaw quit

Barry Irby

Karl, Does the motor have a thermal over load protection on it. Some of mine have a read button on the motor that trips if the motor overheats. Sometimes they trip after you turn the saw off because it takes a few seconds for the heat to soak through to the switch. Now that it is cool, you should be able to push the button and hear a click and it should go back to work if that was the problem. Can't imagine the guy from Laguna did not tell you to check this first, if it exists, so I suspect you don't have one.

Re: Bandsaw quit

#9

karl jr

Re: Bandsaw quit

karl jr

I looked pretty thoroughly for any kind of big (or little) red button on the motor right when it happened. No such luck. After a couple of hours of rest the motor still wouldn't start. Before it quit I probably ran it for only ten minutes. I don't think it's a heat issue.

KTK

Re: Bandsaw quit

#10

OK! Then its broken.

Barry Irby

Re: Bandsaw quit

#11

karl jr

Re: OK! Then its broken.

karl jr

Exactly. But which part?

Tomorrow the ace tech comes in and then I'll find out (knock on wood).

Re: Bandsaw quit

#12

Re: Bandsaw quit

Larry in NW OHIO

Karl It`s been awhile since I worked on magnetic switch, but they are not very complicated. If, like you said, the hum is coming from the switch, then it`s likely in the contacts. The thing I would try is disconect the motor and hit the start botton, and you still get the hum then the contacts inside are either burnt or have dust in them. With the motor disconected and saw unplugged blow it out real good. Then plug it back in and hit the start button ,with the motor disconected, and if it does not hum you may have it. Hook your motor back up and make sawdust. Good Luck Larry

Re: Bandsaw quit

#13

karl jr

Re: Bandsaw quit

karl jr

Talked to another tech at Laguna. Rechecked the voltages. I don't know how I goofed it, but this time I got undervoltage readings in the switch box. 240 volts (2 @ 120v) at the outlet, and only about 50 (2 @ 25v) at the terminal block (?). So it looks like there's a short in the power cord.

How that happened I have no idea, but I'm thrilled that I don't have to replace the motor or the switch. Sometimes a guy gets lucky, I guess.

KTK

Re: Bandsaw quit

#14

Re: Bandsaw quit

Barry Irby

Carl, Not sure what that means, but I think it means something. I used to find weird voltages during Home Inspections. I had an electrician friend that knew what it meant. Unfortunately, he has passed on. I would check the voltage coming from the panel. Hard to imagine a defect in the cord that would create that condition.

Re: Bandsaw quit

#15

karl jr

Re: Bandsaw quit

karl jr

Barry, first let me say thanks for all the help you've been trying to give me. Now, let me confess; I botched my voltage tests. Went back and did them again today. This time I used the terminal with the ground wires attached, and not the one that only looked like it had ground (duh). I also checked the outlet and dismantled the plug and checked that, too.

Everything seems fine. However, my dad told me that since it's a 220V circuit (2 X 120V) the ground isn't really in play the same way it would be in a 120V circuit. That's what I understood anyway, and I'm sure I completely misunderstood what he was trying to tell me.

So, the upshot is that I've recruited help that actually understands this sort of stuff (he's an EE). We'll get this sorted out.

Thanks again,

KTK