Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Welding Magnesium/Lawn Mower Questions OT

Posts

Welding Magnesium/Lawn Mower Questions OT

#1

Welding Magnesium/Lawn Mower Questions OT

Barry Irby

I have been working on my John Deere walk behind mower. It has a plastic chute that funnels the clippings into the bag. The chute got lost and I was trying to install and new one. I was baffled that there was nothing to bolt one side of it to. Then I realised that was literally true. Part of the deck about three inches square is broken out and missing. Its part of the "skirt". My question is, is there any way to weld magnesium? the deck is magnesium and I am wondering about welding in a piece. Of course I would have to find a piece of magnesium to weld. Any suggestions?

Re: Welding Magnesium/Lawn Mower Questions OT

#2

Re: Welding Magnesium

Mark Mandell - Gone Round In Jersey

Un less you happen to have an inert gas-shield welder set up for Mag, you're not going there, I don't think. You'd be way better off to paean a new piece out of 18ga. sheet metal and attach it with pop rivets, then attach your chute.

Re: Welding Magnesium/Lawn Mower Questions OT

#3

Re: Welding Magnesium

Tom Dunlap

An old neighbor of mine would repair my chainsaws after the dropped. Most of the time the parts had to be boiled in a parts cleaner to get the oil out. He did a good job. Since we were neighbors he did the work cheap. At a shop it would have been way too expensive!!!

You could go down to the local lawnmower shop to scrounge up a used deck too. I bet that it wouldn't cost much.

Bolts, sheet metal, epoxy, a block of hardwood...heck Gaffers Tape!

Re: Welding Magnesium/Lawn Mower Questions OT

#4

Re: Welding Magnesium

Dave Nichols

A few years ago Ford made the radiator supports for some of their trucks from magnesium. Body shops were advised not to use heat when trying to repair them. The magnesium can ignite when heated and from what I understand water will not put out the fire.

Re: Welding Magnesium/Lawn Mower Questions OT

#5

Re: Welding Magnesium

Mark Mandell - Gone Round In Jersey

They make very bright flares out of the stuff.

Re: Welding Magnesium/Lawn Mower Questions OT

#6

Pretty Much what I thought.....

Barry Irby

One I am not a welder, not even the easy stuff, so I was not even considering welding it myself. I may have misstated it but I was wondering about having it welded. (not going to happen)

Back in the day I had a bad experience with a magnesium flare. Terrified me. Wouldn't consider personally welding magnesium for fear it might turn my lawn mower into a flare and me into a pile of ashes.

Right now the chute is attached with a heavy copper wire. I reverted to my youth on the farm and fixed it with bailing wire.

The piece that broke out was so square and neat it took me a while to realize something was even missing. I thought about sheet metal and pop rivets. The block of hardwood sounds attractive. (My inner wood worker just kicked in.) If I could figure out how to attach the wood, then I could attach the chute to it. Hmmm.

I will check around on a deck, but that's going to be amazing to find one and it will be like the dentist saying your teeth are fine, its your jawbone that has to go.

Thanks for the help!

Re: Welding Magnesium/Lawn Mower Questions OT

#7

Macguyver Steampunk repair

Tom Dunlap

Using a block of hardwood and some epoxy/bolts would be the perfect repair blend.

If you do epoxy there's a way to add some 'grab' to the patch.

Clean the surfaces, top and bottom.

Drill some 'Swiss cheese' holes in the area.

Glop on the epoxy and moosh it through the holes

Install the patched piece and bolt/clamp it in place

You want the epoxy to mushroom through the parent part to act as a keeper on the bottom

If you want to make a stronger 'plate' on the backside add another layer of epoxy to envelop the mushrooms from the front side after the first layer has cured

I've done this on a couple of gas tanks that leaked with years-long success.

Re: Welding Magnesium/Lawn Mower Questions OT

#8

Re: Pretty Much what I thought.....

Larry in NW Ohio

Barry Go to your John Deere dealer and ask if they have any used ones, if so ask iof they will sell any, and go look at them. You want to look at the ones they want to throw away. See if any of them have good decks. I do this with Toros, I have 3-4 of them and recycle them, take parts from some and rebuild a good one. You also could try a person that repairs lawn mowers also. Watch the papers. If you lived closer I`d just let you rebuild one for yourself. Larry

Re: Welding Magnesium/Lawn Mower Questions OT

#9

Now you are talking....

Barry Irby

All the genes are twitching. Bailing wire and woodworking AND epoxy! Does it get any better?

My best friend's father came through the depression. (the other one) He would have rather fixed something that was broken than have someone give him a new one. Somebody gave him a broken pick. We laughed. What you going to do with a broken pick? He welded the point back on. It was crooked by about eighty degrees. We laughed again at the prospect of digging with such a mangled thing. His answer, I'll just cut it off with the torch and weld it straight. He did. Got years of use out of the pick.

I think I caught some of that from him. Sorry he's gone. There was much to learn there. He was one of the men that won World War Two.

My son calls me Macgyver sometimes.

Re: Welding Magnesium/Lawn Mower Questions OT

#10

Re: Welding Magnesium/Lawn Mower Questions OT

Lee Schierer McKean, PA

Don't try welding magnesium unless you have the proper equipment and training. If it ignites, you won't be able to put it out.

We used to have a Lawn Boy Mower that could be converted from a bagger to an open chute type. The bagger attachment had a plate that fit down inside teh mower to cover the chute outlet. I suspect your John Deere may be the same type of design.

Re: Welding Magnesium/Lawn Mower Questions OT

#11

Re: Welding Magnesium

Bill Houghton, Sebastopol, CA

I concur - fabricate a new chunk. You probably don't need a big piece - sheet metal shops all have scrap bins below the shear, and, if you are lucky and charming, you might be able to get a piece the right size for free or really cheap.

I personally wouldn't use pop rivets on it, though - might not be strong enough, and I don't think you want a piece of sheet metal falling down from the mower deck during operation. Pop rivets to hold it in place while you drill for bolts, now, that's different.

By the way, I don't know how cast magnesium is as far as crack propagation. Often, on a casting, it's a good idea to lightly countersink both sides of any hole to reduce sharp arrises that can encourage cracks to propagate once they start.

Re: Welding Magnesium/Lawn Mower Questions OT

#12

Re: Welding Magnesium

Larry in NW Ohio

Barry If you go the way of bolting it on, make sure you use stainless steel botts and washers, and nuts. But get good ones made in the USA. The China SS is not very good from the ones I bought. Good Luck with it. Larry

Re: Welding Magnesium/Lawn Mower Questions OT

#13

Re: Welding Magnesium/Lawn Mower Questions OT

Dave Paine

Barry, I bought some rods at a Woodworking show. Claimed to work will any non-ferrous. I have only used once for Al. It worked, although consistent temperature can be a challenge. Too much heat and rod stays liquid so piece may not stay in place during operation.

I do not have website, but the instructions state "brazingrod@earthlink.net"

Re: Welding Magnesium/Lawn Mower Questions OT

#14

Went to the dealer/repair shop today

Barry Irby

Checked to see if they had a junker lawn mower I could buy and swap out the deck. They told me the deck is no longer available for the mower I have, even if I were willing to buy a new one. (NOT!) They did not have a mower that was identical to mine, but they did have one that was newer. The deck was the same as mine except that it was (John Deere) green instead of silver. I would have bought it at a reasonable price except for a minor problem. It was damaged similar to mine, but worse. My MacGyver gene is twitching.