Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

bristle skirt for dust collector

Posts

bristle skirt for dust collector

#1

bristle skirt for dust collector

Howard

Entry 817 of Wood Centrals �Americas top shops Contest� by Alan Schaffter shows a table saw dust pickup with a bristle skirt to contain the dust. Anyone know with I can buy the bristle skirt material.

Thanks

Howard

Re: bristle skirt for dust collector

#2

Re: bristle skirt for dust collector

Don Newman

Howard,

Here's Alan's reply when I asked him.

If you go to catalog page 1239 on the MM-C web site and look at (or search for) the section on "Metal Backed Strip Brushes" you will see the ones I plan to use on my next version. I cannibalized a broom for the prototype but the bristle were too thick and stiff and hard to mount. Various sizes are listed but for flexibility, weight, and length, I chose 74405T11.

74405T11

Galv Steel-Backed Nylon Conveyor Strip Brush 3/16" W X 7/32" H Backing, 6" Overall Height

I also got some aluminum Strip Brush Holders from the section below on the same page which I will use it to hold the brush strips on the next version. I plan to use #6 for the over-blade guard to help keep the bristles away from the blade a bit more, and #4 for the shroud I intend to build for my SCMS. I hope this helps.

Alan

Re: bristle skirt for dust collector

#3

Re: bristle skirt for dust collector

Carol Reed

When I had my CNC, I used the brush sweep for doors. Check your borg for door sweeps. They were relatively inexpensive and very available.

Re: bristle skirt for dust collector

#4

Re: bristle skirt for dust collector

Barry Irby

I tracked down a company that makes the ice scrapers that have a brush on one end and they sent me some free. (Nice people)

I also tried to find the ones they use on tractor trailers around the wheels but never found them. A trailer manufacturer should be able to find some.

Re: bristle skirt for dust collector

#5

Truck  / trailer brush or skirt

Gary Camp, Bend Oregon

Trailer brush may be a bit stiff, and it can be expensive. You ought to be able to find it in any town large enough to have a full service diesel truck repair shop. The plus side of truck brush you can find it with pretty long bristles.

glc

Re: bristle skirt for dust collector

#6

Why

Mark Mandell - Gone Round In Jersey

Wold you need/want fibers longer than 1-1/2" anyway? Truck stuff is 6-12" long and would block the operator's view of the cut

Re: bristle skirt for dust collector

#7

Re: Why

Larry in NW Ohio

I`ve had these on my saw since 04, at least that is the date I have in my McMaster catalog. They are the best thing I found to keep dust from flying all over. You can get a lot of different ones in McM.Larry

Re: bristle skirt for dust collector

#8

Right

Mark Mandell - Gone Round In Jersey

I modified my Excalibur guard with 1" brushes all around. They do the job of an air-curtain to control dust coming off the back and top of the blade. However, using 6-12" truck fringe seems silly to me, hence my question. . .

Re: bristle skirt for dust collector

#9

Re: bristle skirt source

Al Stokka - Cambridge, Iowa

Howard,

Sealeze makes the stuff. www.sealeze.com. 800-787-7325. industrial@sealeze.com.

I posted information (including pricing) on or about mid-March, 2008.

Al

Re: bristle skirt for dust collector

#10

Long bristle

Gary Camp, Bend, Oregon

I was working on an idea for downdraft dust colection on a SCMS where the saw rail poked through the bristles. I used strips of foam fabric instead, worked so-so contains the dust fairly well but doesn't "suck" it up to well, need more area for draft I think.

glc

Re: bristle skirt for dust collector

#11

Air Curtain

Mark Mandell - Gone Round In Jersey

For collection on the SCMS, I use a hood and drop box fitted to the 6" system. Pulls through the drop and several ports in the hood. Then, across the front edge of the box I made an air curtain of 1" strips of Poly-E sheet slightly weighted at the bottoms. They hang just behind the fence. Does very well keeping the dust inside the box where the DC pulls it out.

Re: bristle skirt for dust collector

#12

Picture Answer

Mark Mandell - Gone Round In Jersey

Went back to the pix of Alan's shop and the answer to the 4" bristles is now apparent. Since his table saw head is rigid, he needs the 4" bristles for stock clearance when he doesn't fold the head up. With a floating overarm guard like mine that, a shorter brush can be used.

Re: bristle skirt for dust collector

#13

Re: bristle skirt for dust collector *PICs*  *LINK*

Alan in Little Washington (NC)

Don, thanks for stepping in! I was out of town so couldn't respond.

Disclaimer: My rig is a dust shroud NOT a blade guard!

I built my rig for 4 reasons:

(1) I didn't want a big plastic shroud

(2) I didn't want a parallelogram or other complicated mount

(3) I wanted something that the stock could easily push out of the way

(4) I wanted something that would still conform to the stock when I fed it into the blade. Big gaps are left on the sides when stock is fed into most other hard dust shrouds.

The bristles- I used bristles I canabalized from a broom. Truck and RV splash guards are NO GOOD, too thick and don't have enough bristles. The ones I got from McMaster-Carr (see Don's post) are much better than both. Whenever I get around to installing the new bristles I will use angled mounting strips (see MM-C)

I mounted my abbreviated plastic shroud high enough so most stock won't touch it- 4" above the table. For thicker stock or when using jigs it folds out of the way. For thick stock, the blade is buried in the stock and doesn't throw much dust anyway. I extended the Lexan front so I could look down from the top to see the leading edge of the blade, pencil marks, etc.

Original, prototype shroud:


Lower unit folded:


Full rig. Ceiling mount and sway braces are adjustable. Upper braces are made from EMT electrical conduit, lower braces from broom handle left over. Small band clamps hold them tight.


I used 3" flex and 3" ASTM 2729 S&D PVC. Upper portion of wye is blocked.


Gravity and three pairs of rare earth magnets hold the lower unit down. My DC and each blast gate are fully automatic- gates are machine triggered and electro-pneumatically operated. When the saw is running, two blast gates open- one feeding the over-blade pickup, the other, the saw's cabinet. If the pickup is folded, a magnetic reed switch in the upper ply hinge plate (wires visible in pic) and a small rare earth magnet in the lower plate separate, opening the switch. That causes the over-blade blast gate, located behind a knee wall, to close. The cabinet gate stays open until I turn off the saw.


Below is a link to a rather long video tour of parts of my DC system and demo of my autogates.


DC system tour & autogate demo