Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

Band Saw Restoration Day 2

Posts

Band Saw Restoration Day 2

#1

Band Saw Restoration Day 2

Ken Bellock (Houston, TX)

I called MiniMax today, but was only able to get ahold of the parts department. Out of curiousity I asked how much it would cost to get a replacement set of tires. They said for my model that they do not sell the tires by themselves, but that they do sell the tires with the wheels attached... the wheels were not free in the deal. Though the parts guy said he didn't know for sure he said his guess was my wheels were either flat, or had a negative crown. :( He did say to call back tomorrow a bit earlier and talk to the tech guys and that they should know for sure. I'll give them a call, but still couldn't stop messing with it, so I took a small needle, pushed it through the high point of the crown and marked the end with a sharpie. Comparing the penetration depth to the edge of the wheel makes it look the tires are the same thickness across the wheel, so maybe the wheel is crowned and the urethane tires will work. I think I will end up shelving the tires and bearings for another day either way and move on.




The next hang up, literally, was that the upper guide bar would not go all the way up. After removing it and cleaning everything, I can see where contact is being made with the wheel.


Loosening these two screws and making several adjustments, I was able to get the bar to sit where it was supposed to far away from the wheel now.


Re-installed the upper guide arm, and installed the new carter guides. Boy are they pretty, and we are starting to get somewhere!


Uppers were so easy, figured the lowers would be too... oh well, looks like carter designed the lower bearings for some other shaped SCMI S-45 band saw...


I could just file the hole longer, but I think i will give them a call tomorrow first and see if they are aware of the problem. Perfect time to call it a night.

Looking forward to making some dust with saw some day...

Re: Band Saw Restoration Day 2

#2

Re: Band Saw Restoration Day 2

Thomas S Stockton

Ken

I have the same saw and the wheels are crowned, I just went down and checked. The rubber on your wheels looks fine, I would clean them up a little bit and see how they work. I spun a bearing on my lower wheel and looked into a replacement it was over $300 15 years ago. Had a machine shop fix it a whole lot cheaper than that. I've never had to replace my tires and they look like yours. I might have the owners manual around if you want a copy although it is kinda useless.

Tom

Re: Band Saw Restoration Day 2

#3

Be careful with urethane tires

wilbur

I have an old Walker-Turner 16" bandsaw whose tires were n terrible shape when I got it. I figured it wouldn't be such a huge deal, as I could easily replace the old rubber tires with urethane tires.

What I didn't take into account is that the wheels on my bandsaw are flat in profile, and more importantly, don't have a raised lip around the rim like the profile on the ubiquitous Delta 14" bandsaw wheel, like this one:


I was using my bandsaw one day, and as I was making a cut, the bandsaw started shaking, and I hit the off button and backed up. Suddenly, there was a bang, and the blade just stopped, and the top urethane tire shot out of the opening where the blade exits the top wheel compartment.

What had happened was that the urethane tires had stretched over time, and since you don't use adhesive to attach these tires, and since there wasn't a raised lip around the edge of the wheel, the tire slipped off.

I replaced the urethane tires with rubber ones, and used adhesive to glue them on.

You might want to take that into consideration as you go about replacing the tires. It looks like your wheels also have a flat profile and no lip around the edge.

Re: Band Saw Restoration Day 2

#4

more details, please

Bill Tindall

Maybe in a separate post would you describe your experience installing the rubber "conventional" tires.

Re: Band Saw Restoration Day 2

#5

Re: Band Saw Restoration Day 2

Ken Bellock (Houston, TX)

I found a copy of the users manual on the MiniMax web site. Your right though, it is pretty much useless. Might as well be written in italian... I bought the replacement bearings for the lower wheel already, have them sitting on the workbench. I bought those direct from MiniMax, through the phone number on their website. The lower bearing was $8... plus $16 shipping and handling if I remember correctly. I don't know what would have cost $300... maybe they were giving you a quote on the whole wheel, like they did for me when I asked for just the tires.

Re: Band Saw Restoration Day 2

#6

Re: Band Saw Restoration Day 2

Thomas S Stockton

The quote was for the whole wheel. If you run into any problems feel free to email me and I can look at my machine or take pics for you

Tom

Re: Band Saw Restoration Day 2

#7

two options

Robin Corell in Atascadero CA

The most common way is to stretch the tire on to the wheel and then insert a piece of dowel between the tire and the wheel so you can apply some contact cement. By rolling the dowel around the wheel gluing as you go you end gluing the tire onto the rim. As you can imagine this is a messy endeavor and it is not with out its faults. The biggest one is that you end up over stretching the tire as you glue it and the last little bit has less tension and is therefore a bit thicker.

The traditional way to glue tires before modern adhesives was to use shellac. This is how I glued the tires on my first bandsaw. You start by painting some 3 lb shellac onto the rim and before it dries stretch the tire onto the rim. Let it sit 24 hours and it is good to go. I did have a 'flat' after about 7 or 8 years, a 6" section of one tire came loose. I slid a brush with some fresh shellac in the loose area and let it sit over night. The tires were still tight after 14 years when I sold the saw.

Robin

Re: Band Saw Restoration Day 2

#9

Re: thanks

wilbur

The first method was how I did it. I didn't have any issue with overstretching, but once I got the contact cement applied to the whole tire, I ran the dowel around a few more times which took care of any stretching discrepancies.

The process is certainly not as mess-free as mounting a urethane tire, but it's not as terrible as I thought it would be, either. It only took about ten minutes per tire. The contact cement drips were easy to clean up since I had put down newspaper to cover my work surface. And I'd much rather deal with a half hour of dealing with a glue up mess than have the tire come off the bandsaw wheel in the middle of a cut again.

One other advantage: I haven't done this yet, but since the rubber tire is thicker than urethane tires, I'll be able to put a crown on the tire more easily, which is the first thing I'll be doing once I get my workbench done, and my lathe disassembled and relocated to its new location in my shop (long story).