Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Bandsaw Restoration Project

Posts

Bandsaw Restoration Project

#1

Bandsaw Restoration Project

Ken Bellock (Houston, TX)

I'm trying to bring some new life back to some old steel. Thought I would share some pics of the process, and ask a few questions. I figure someone here has walked these steps before once or twice. My knowledge consists of a subset of what anyone would get from reading "The Bandsaw Book" from cover to cover a couple of times...

Here is the beast, a rescue from craigs list. I found her being abused in a small car shop. They had just upgraded to a bigger monster that was actually designed to cut metal, and they had no more love for this old beauty.


There was some dissasembly before I started taking pictures... Here is her pedigree.


And the rest of her...



I started with the easy stuff, installed a mobile base, replaced the V belt with a link belt.


Mounted some magnets into the stone for tuning the blade.


And did a lot of cleaning... little bits of aluminum everywhere!


In addition to removing the table, I removed all the guides, and the upper guide rail. It had been installed wrong or moved, and was grinding against upper wheel. There was some rust in there too, so it was good to get it all out, cleaned, and coated with boeshield. The lower guides looked like they had never been touched before. This is what the current rubber tire looks like.


From the picture, it may almost look ok, but there are chunks missing, and aluminum embedded in it everywhere. So sitting on my workbench is the following pile of parts to be installed. Two bearings, one for each wheel, the current bearings seem to be in great condition, but while I'm in there, why not. Two urethane tires. Was hoping to be able to salvage the tires that were on there, but they are just in too bad a shape. And last but not least, a bright and shiny set of new carter guides, yipee!

Got a good bit of work done on her tonight, but I got to go to work in the morning... a good thing I can claim, at least for the next couple months... and I got stuck, so it was a good time to call it night. My first question for those more experienced then is how to get past this first hurdle.


I took the bolt off that secures the bearing to the axle, but the wheel will not come off. I don't want to force it, or pry it off (I've already paid enough for the parts I have sitting on the workbench!) so how do I get it off safely? I know once it is off to tap the bearing out with a block, and then to use another block and a clamp to press the new ones in. Just need to figure out how to get the wheels out first!

Thanks in advance for any advice you can throw my way, I'll post more pictures if there is an interest as the project unfolds.

Ken

Re: Bandsaw Restoration Project

#2

Re: Bandsaw Restoration Project

Ken Bellock (Houston, TX)

Looks like all the pictures didn't upload right for my original post, here are the pictures that didn't make it.


I started with the easy stuff, installed a mobile base, replaced the V belt with a link belt.


Mounted some magnets into the stone for tuning the blade.


And did a lot of cleaning... little bits of aluminum everywhere!


Re: Bandsaw Restoration Project

#3

Re: Bandsaw Restoration Project

Robin Corell in Atascadero CA

Those tires don't look all that bad. I have used many saws with worse looking tires that worked just fine. I would adjust the blade guides and see how it runs before tearing the tires off. and actually I would be tempted to do a light recrowning before I replaced them.

I am not familiar with mini max, other than knowing they make really nice tools. Are the wheels themselves crowned? I put carter blue urethane tires on the saw I have now and I am very happy with them. however the wheels on my saw are crowned which makes crowning the tires unnessesary. this is a good thing beacuse the urethane tires are not thick enough to allow crowning and since they are not glued to the wheels it wouldn't be as acurate as the old neoprene.

My old saw had the more standard non crowned wheels and I put new neoprene tires on it. It is not that hard of a job if you do it the old school way and use shellac to glue the tires to the rims. The wet shellac acts as a lube and it holds just fine. much less messy and faster then contact cement.

If the bearings arn't making noise I would leave them in. My old saw was made in the mid 1920's and had ben sitting outside for several years before I got it. I did have to replace the bearings in the upper wheel but the bearings in the lower wheel were just fine. My current saw was made in 1959 and all the bearings are just fine. I would be surprised if the bearings in your much newer saw are worn past just getting broken in.

Nice saw and it should be a keeper one it is up and going.

Robin

Re: Bandsaw Restoration Project

#4

Moses Yoder

Re: Bandsaw Restoration Project

Moses Yoder

I would put a pulley puller on the wheels to pull them off. Tighten it down pretty good then tap the end with a hammer to pop the wheel loose on the shaft which is probably keyed. I have no experience with Mini Max though so take this for what it is worth.

Re: Bandsaw Restoration Project

#5

Re: Bandsaw Restoration Project

Ken Bellock (Houston, TX)

The bearings are silent, and the wheels are perfectly balanced. I wish I knew if the wheels had a crown in them or if it is in the tires; I have a set of blue carter tires to put on there, and it would be a lot easier if the wheels had the crown in them already. I may try sanding the wheels down lightly tonight and see if that gets rid of all the embedded bits of aluminum and smooths out the missing chunks. If there is going to be an improvement with the new tires, I'm more than willing to do the extra work, I just would not want to rip off the old tires, find a flat wheel, and then learn the tires I bought will not work and have to track down replacements of the originals...

Re: Bandsaw Restoration Project

#6

Re: Bandsaw Restoration Project

Robin Corell in Atascadero CA

Flat wheels are much more common than crowned ones and for that reason alone I would be reluctant to relpace the existing tires with flat urethane ones. Sand paper by hand will not do much to even out your wheels. you will need to use a disc sander and it needs to be done while the saw is under power. I had my local shop weld up a band mae out of metal straping when I did this to my old saw. that way I could have the saw running with one of the doors open and not have a blade wizzing by. An alternative to this is to rig up a fixture to hold a router with a traight spiral bit and slowly turn the wheel by hand. If you go with a router you will have to make the fixture so the router can be postitioned several times to get a crown. do a search over on OWWM for more info on crowning bandsaw tires. Replacing them is easy doing it right is a lot of work.

The small grove and even the bits of aluminium in your tires should not had any detrimental effect on the saws performance if the blade guides are adjusted properly.

You should be able to get most of the aluminium bits out with a stiff wire brush, those that won't come out won't be a problem.

Re: Bandsaw Restoration Project

#7

Has anyone told you

Bruce, a MN Galoot

YOU SUCK!



That's one really nice score. Good work!