Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Carved Coffee Table II-Part 2 Carving legs etc *LINK*

Posts

Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#1

Alan Young

Carved Coffee Table II-Part 2 Carving legs etc  *LINK*

Alan Young

>Earlier this week I posted a series of pictures and descriptions of the joinery of a coffee table. (See Link below).

Today I have a set of pictures showing the shaping and carving of the legs and apron sections. Let's look at the leg profile and design pattern from the first table


The profile is a generously shaped cabriolet form.


The carved design is an acanthus leaf descending from a flowered shell figure. The leg profile narrows as the foot ends in a modified French Toe- a small carved scroll on "point"


The carving's on the legs and aprons for the new table will will be different.

A Fleur de lis element, a descending diamond and "C" scrolls will be implemented on this table.

The legs are still in fairly rough form



Now I'll shape the legs through the use of a spokeshave and various carving gouges, and files


I carved the Fleure de lis elements separately. I drew the design then cut the lines into the wood with various gouges.


From there it's a matter of removing the background till the element is "raised




Once each piece is defined I cut it from the stock and begin another.


Each element gets glued to the top of a leg. I'll refine the carving further once the piece has set.





Next I'll start carving the apron sections.

The end and side sections of the apron each have a descending block.


The profile of these sections is transferred to smaller pieces that are cut out and glued to the apron. From there the surface is filed and carved.


The design for the end apron sections has a repeat of the descending diamond in the center block.


The side apron sections will have the descending diamond in the center block with "C" scrolls on either side.



A simple scroll bead detail runs from the center block around the apron ending in another scroll where the leg joins the apron.



It will probably be some time before the next set of pictures as I�ll continue the long process of refining the carved elements.

Alan


PART 1

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#2

Re: Carved Coffee Table II-Part 2 Carving legs etc

Jim Shaver

>NOW That's a Piece Of Art! :D And the Red Wing sweat top is too... ;)

Seriously Alan, your attention to detail and process are inspiring my friend, the carving alone is Insane!! :b

I always enjoy Your sharing and energy, a class work by a class guy!

take care.

Jim

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#3

Re: Carved Coffee Table II-Part 2 Carving legs etc

Larry in NW Ohio

>Alan I just love reading and looking at your work, or I should say hobby. Just like Tom, I wish I had just a small part of your imagination and talent, but there is one area we are alike though, we have the same hair design. Larry :) :D 8) 8)

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#4

Re: Carved Coffee Table II-Part 2 Carving legs etc

George@Colonel's Workshop-Havertown PA

>Good Afternoon Allan,

I'd almost rather look at your pix/posts than retire to my shop today. I'm getting a late start, and am happy I chose to come see your work first. That attention to detail is an inspiration to all of us. Keep us posted as the table "matures in majesty".

George

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#5

What a great tutorial!

Bruce, a MN Galoot

>Thanks for the inspiration.

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#6

Ellis Walentine

Re: Carved Coffee Table II-Part 2 Carving legs etc

Ellis Walentine

>Thanks, Alan, for your great documentation. That table is going to be a beauty.

Keep up the good work.

Ellis

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#7

a most enjoyable read

Bill Tindall

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#8

Fabulous,,,,and a Question

Barry Irby

>The first table is gorgeous and this one is on its way. Thanks for sharing.

My question is why do you carve the top of the leg and apply it as a separate piece? Why don't you carve directly on the leg?

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#9

Alan Young

Because I painted myself into a corner so to speak

Alan Young

>My question is why do you carve the top of the leg and apply it as a separate piece? Why don't you carve directly on the leg?

A good question. These legs were cut out almost two years ago when I made the first table. When I made the first table-the joints between the apron and legs were actual mortise and tenon.

Hard to see but it shows in this picture:


As I resumed work on this table a number of weeks ago I decided a pair of loose tenons in each leg/apron joint would be a good idea-I also hadn't really decided what carved elements were going to be displayed on these legs before I cut the joinery. Once the double mortises where cut I didn't like the thought of carving with such a thin background. If you look at the profile of the top of the legs here you can see that the thickness of the applied carving is quite close to the thickness of what I had left after cutting the mortises.


It's going to take some more finessing of the lower line of the applied carving to make it look "happy" with the descending diamond element..Truth is it would have been better to have cut the original profile a 1/4" or so thicker at the top but it was what it was. So I decided to carve the Fleur-de lis elements separately. If I ever build another one of these pieces I will plan it out better.

Alan

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#10

Part of the journey

David Yoho

>If I ever build another one of these pieces I will plan it out better.

I can relate. After building several of any item, I always find ways to refine the process, which will make it better or quicker the next time out. I think it's all part of the journey woodworkers experience.

Nice job, Alan!

David

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#11

Re: Because I painted myself into a corner so to s

Barry Irby

>Oops, a design opportunity. We have all had a few of those. Nice recovery. I don't carve anything so I wondered if it were some mystic carving thing I did not know about. I was trying to figure out if it had something to with grain match or expansion. I am confident I will never manage to make a piece like this. Thanks for the post.

Re: Carved Coffee Table II-Part 2 Carving legs etc *LINK*

#12

Re: Carved Coffee Table II-Part 2 Carving legs etc

Bill Schreiber

>Wow. Incredible that you can do such beautiful carving and not screw up! Awesome work.

Regards,

Bill