Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Super Resolution Thermal Imaging Camera

Need Rockwell Sonicrafter Dimensions

Posts

Need Rockwell Sonicrafter Dimensions

#1

Need Rockwell Sonicrafter Dimensions

Larry In Lima

>Hello, I am looking for dimensions of a "part" on a Rockwell Sonicrafter. This tool is kind of like a Fein Multimaster, seems like everyone is making one now. If someone has a micrometer or other accurate way of measuring... Could you tell me the dimensions across the flats of the hexagon (blade area) ? Feel free to email me or post here. Thanks a lot, Larry

Re: Need Rockwell Sonicrafter Dimensions

#2

Re: Need Rockwell Sonicrafter Dimensions

Carlos Clarke

>I have the RK5100K model.

It doesn't have a hex shaped tool.

The manual doesn't list such a tool

for models RK5101K or RK5102K either.

Re: Need Rockwell Sonicrafter Dimensions

#3

.546"

Robin Corell in Atascadero CA

Re: Need Rockwell Sonicrafter Dimensions

#4

Re: .546"

Larry In Lima

>Thanks - I appreciate it - can anyone else confirm? Larry

Re: Need Rockwell Sonicrafter Dimensions

#5

Re: .546"

Robin Corell in Atascadero CA

>I know that sounds like an odd size but it is about .005" under 14mm. I am guessing that the 12 point hex hole in the blades is 14mm.

Robin

Re: Need Rockwell Sonicrafter Dimensions

#6

Re: .546"

Larry In Lima

>Thank you very much - I appreciate it a lot. Reason I ask is for making some adapters, to use multiple brand blades on 1 tool. It has already been done for the Fein, whose blades are very expensive. I own a Fein, and the cost of the blades and the constant loosening while using was reason enough to develop an adapter for it, now the Rockwell. Thanks for the responses - Larry

Re: Need Rockwell Sonicrafter Dimensions

#7

Re: .546"

Robin Corell in Atascadero CA

>I was impressed with the solid feel of the Rockwell but to be honest the reason I choose it over the others it that for $200 it included both tungston carbide blades, a wood blade, a wood/ metal combo blade, large and small sanding pads with a bunch of sandpaper, the scraper blade and a couple of felt pollishing pads. I didn't realize what a vaulue this was untill I needed to replace the wood/metal combo blade and it cost $20.

I have since been resharpening the blades with a diamond cup wheel in a fordom, But I think a cut off wheel in a dremel would do the job just as well. The baldes are not impulse hardened so I should be able to sharpen them down to nubs. I don't know how they will perform once I grind past the set that he wavy edge provides. If I need to I can add it back in with a ball pean hammer.

I imidiatley thought the blade chucking method was a potential for failure. If the sharp corners of the hex head become rounded the tool will become worthless. For that reason I have paid close attention to properly mounting the blades and tightening them. so far I have not had any problems and I have really put mine through the ringer. The only weakness I have found is that sheetrock dust can jam the switch. It works prperly adter a good cleaning but it was a suprise that that is its achillies heel.

Robin

Re: Need Rockwell Sonicrafter Dimensions

#8

Re: .546"

Larry In Lima

>Robin, what is the model number on yours if you don't mind me asking? Seems like there are a couple flavors out there on these... Larry

Re: Need Rockwell Sonicrafter Dimensions

#9

Re: .546"

Robin Corell in Atascadero CA

>Mine is a variable speed model# RK5102K. From looking at their web site there appears to be a non variable speed unit availabe but They all look the same and I would guess that they all use the same blade mount system because all the accesories fit all models.