Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

TS Problem

Posts

TS Problem

#1

TS Problem

Jerry Draper

>I have a Delta contractor's saw. I have never been able to get a perfectly straight edge whenever I rip a board. The board always has about a 1/32 inch concave hollow in the middle of the cut. I have checked and double checked all alignments between the blade, table,slot, fence, etc. I find nothing out of whack. Is this inherent in the saw or is there some way to obtain a perfectly straight cut?

I would appreciate any ideas anyone might have.

Re: TS Problem

#2

Re: TS Problem

Chuck in ND

>What fence are you useing with the saw ? Are you checking the crown on the board before runing it through the saw ? Are you useing a good blade ? How old is the saw, and what is it's history ? Was it ever used in a commercial enviroment ? I have had a Delta Contractor's table saw with a Unifence since 1995 and have had no problems with it.

Re: TS Problem

#3

Check the alignments again...(sorry!)

Grant in Iowa

>Check alignments again... if your blade is a sharp dedicated rip blade (suggest a Freud or better), then check in order:

1. Miter slot to blade parallelism. Dial indicator setup mounted to your miter guage is best, but a board clamped to your miter guage and some feeler guages can also do the trick. Dial indicators can be had for as little as $15 at places like Harbor Freight.

2. Miter slot to fence parallelism... again... dial indicator is best, but other methods can work if you are careful. While you are doing this, move your fence left and lock it, right and lock it, etc a few times to be sure that when it is locked in place it remains aligned the same. Lots of low end fences that lock in the front and rear of the saw table suffer in this regard. If the fence can't lock and provide repeatable parallelism, then it is to blame.

3. Fence straightness: Use your best straight edge to see how straight your fence is. You can also detach the fence and lay it on its side on the table saws top to check it.

Tell us how these checks work out, and tell us what kind of blade you are using (brand, and number of teeth) and we'll offer more input. Also tell us the brand and model of the saw, since many of us will have direct experience with adjusting it.

It is also possible that the wood you are cutting is not evenly dried or has internal stresses for some reason. If you rip a board and then lay the two back together, they should fit together tightly... if not then the board, not the saw is to blame.

Regards,

Grant in Iowa

Re: TS Problem

#4

And, I might add *LINK*

Grant in Iowa

>One thing I added to my saw is a board buddy setup. I did it just as the photo shows, except I bought a cheaper track that accepts 1/4-20 bolt heads to hold them down.

Excellent product, great results, adds safety and accuracy to every rip cut.

Regards,

Grant in Iowa


http://www.rockler.com/product.cfm?page=11262

Re: TS Problem

#5

Re: Check the alignments again...(sorry!)

Chuck in ND

>Grant, when ripping boards the only thing that needs to be parralell to the blade is the fence, the miter slot has nothing to do with it unless your doing crosscuts.

Re: TS Problem

#6

Re: TS Problem

Jerry Draper

>I bought the saw new about 5 years ago. It has a Unifence and I have tried a variety of different blades. I do check the board edges before ripping and I have tried skewing the tail end of the fence away from the blade.

All to no avail.

Re: TS Problem

#7

Re: Check the alignments again...(sorry!)

Lee Schierer - McKean, PA

>If you have a dial indicator, mount it on your miter gauge and then move the fence over to engage the dial indicator tip. Clamp the fence and zero your dial indicator near the front edge of your table. Then slide the miter gauge across the table watching the reading against the fence. The reading should stay on or very near to zero if your fence is straight.

A concave cut would indicate that the ends of your fence my be angled slightly toward the miter gauge as compared to the middle of the fence near the front edge of the blade. A curved fence would likely give you a concave cut.

Lee

Re: TS Problem

#8

ebd

Re: Check the alignments again...(sorry!)

ebd

>The reason to use the miter slot is that it runs the full length of the fence and so you can get a much more accurate measurement. Using the 10" of the blade isn't as accurate. I had to align the blade (trunion) to the miter slot on my Delta 10". It was a PITA but worth it. Not only wasn't the blade parallel to the right slot, the left slot wasn't parallel to the right slot. Only off by a wee bit, but enough to matter. Now I've trued everything to the left slot and have had no more problems. I can cut segments for bowls perfectly and rip perfectly. I can't use the right slot though, because it's slightly off.

Picture to show tightness of segment joints. !2 segments/ring.


img

Re: TS Problem

#9

ebd

Re: Check the alignments again...(sorry!)

ebd

>Sorry - picture is thumbnail - here's a better one.


img

Re: TS Problem

#10

Re: Check the alignments again...(sorry!)

Jerry Draper

>Thanks Lee, that sounds like it may be my problem. I don't currently have a dial indicator but I will buy one soon.

Re: TS Problem

#11

ebd

Re: Check the alignments again...(sorry!)

ebd

>OK one last try.


img

Re: TS Problem

#12

Re: Check the alignments again...(sorry!)

Tony - Memphis

>Just be careful. Using a dial indicator, one can get carried away! Not many surfaces are flat within a few thou,so you'll get a variance due to the fence itself, not the overall alignment. You can drive yourself batty messing with it. Dial indicators are great to have around though. Go ahead and get yourself a magnetic base while you are at it. You'll find all sorts of things to use it on in the shop. Let us know what you find out. I used a Delta CS for many years and it seems like I was always chasing some error with it. I'd get it all lined up and then things would move. Like hanging the motor moving the blade. Frustrating at times, but I made a lot of furniture on that saw. Now it's being used by Habitat for Humanity to help build homes for those in need.

Tony

Re: TS Problem

#13

Re: Check the alignments again...(sorry!)

Chuck in ND

>I guess I don't get that carried away with stuff, most of what I make isn't Fine Woodworking material, perhaps I'm in the wrong Forum. I do however like good tight glue joints as much as the next guy and I usually get them. I guess if I was worrried about Machinist tolerances on equipment I'd be a Machinist.

Re: TS Problem

#14

Chuck... you are correct...but:

Grant in Iowa

>If I had simply directed him to focus on blade to fence parallelism, then he might end up with a machine that burns the wood and gives poor cuts on crosscutting.

The order in which you check alignment on a saw or many other devices is very important. I simply provided that order up through the step that would ensure a good result.

Regards,

Grant in Iowa

Re: TS Problem

#15

Re: Grant, I totally agree with you

Chuck in ND

>Some people do alot of crosscuts on their table saw, I just didn't feel like giveing a full blown table saw alignment tutorial for only one table saw operation. But you are correct, excuse my laziness.

Re: TS Problem

#16

Here's an option

Bricofleur

>Jerry,

A temporary option would be adding a much longer auxilliary fence to your Unifence. Just be sure it is straight, and if needed add shims between it and the Unifence.

Best,

Serge

http://www.atelierdubricoleur.spaces.live.com

Re: TS Problem

#17

Re: Featherboard ?

Chuck in ND

>Maybe a featherboard to keep the material tight up against the fence is the answer. It's really tough to diagnos these problems without being there to see whats going on.

Re: TS Problem

#18

Re: Check the alignments again...(sorry!)

David Hay @ Denver

>Grant brings up a good point. Do you get this problem on solid wood only or plywood as well? With solid wood, you can never really know what will happen until you've cut the board, as internal stresses may be released, even on really dry boards.

David

Re: TS Problem

#19

Every time I've had that problem

Bruce, a MN Galoot

>it turned out to be that my blade wasn't as sharp as it should be. This is particularly true if you use one side of the blade to true up the edge or end of a cut. Get the blade sharpened properly and give it a whirl.

Re: TS Problem

#20

Re:What Bruce said and

Chuck in ND

>And, or your trying to push the board through too fast.

Re: TS Problem

#21

I don't think anyone mentioned

Gary Camp, Bend, Oregon

>a misaligned splitter. on my saws it is happens ocasionally, watch you cut and see if things stay lined up until you hit your splitter and then start to move relative to the fence. That is my most common misalignment problem.

glc

Re: TS Problem

#22

Re: TS Problem

Barry Turner

>Before the advent of better wood glues, joiners strived for glue joints that were slightly concave in the middle, so that the ends of the boards would be forced more tightly together when clamped. This allegedly gave a better glue joint. I don't think this approach is necessary anymore, but your problem may not really be such a problem. Especially, if you have a good, accurate jointer.

Re: TS Problem

#23

Re: TS Problem

DP

>I had the same problem with a Delta contractor saw some years ago. Solved it by installing a PALS alignment system. Easy to install and easy to align the saw and to realign it if it ever goes out (mine did once but hasn't again in about 8-10 years). You can get it from Woodcraft (and maybe other places as well). Costs about $20 and worth every penny IMO. No affiliation with either Woodcraft or the maker of PALS.

http://www.woodcraft.com/Family/2020591/PALS-Contractors-Table-Saw-Alignment-System/videos.aspx

Re: TS Problem

#24

Re:Thanks to all. Several new things to try.

Jerry Draper

>

Re: TS Problem

#25

Re: TS Problem PALs

Chuck in ND

>I've never tried the PALs yet for one reason, I'd like to see them made from steel instead of aluminum, I'm just afraid that they'd be too easy to bend. Is my concern valid ?