Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Resawn veneer backer

Posts

Resawn veneer backer

#1

Resawn veneer backer

Jeff

>I am going to be resawing some Sassafras to make veneer for some drawer fronts and panels for a platform bed. Unfortunately, I won't have enough Sassafras to make the backer veneer, so I'm looking at other species.

In searching around the internet for wood movement calculators, I've found that, of the readily available species, Alder and Ponderosa Pine have the closest shrinkage rates when drying, but I wonder if those properties translate to already dried wood. Can I presume that the drying-shrinkage numbers are similar to the already-dried numbers?

If the above numbers are good, I also wonder how close I need to be on the backer material. For instance, Ponderosa's shrinkage percentages are within 3% of Sassafras, and Alder is within 10%. Poplar, which is markedly cheaper (and easier to find than Ponderosa), is at 15%. Is this too large a difference?

Thanks for your input, and a Happy New Year to all,

Jeff

Re: Resawn veneer backer

#2

Unnecessary fretting

Bill Tindall

>there was an architectural plywood company located near-by. They used what ever leavings they had around to form the back ply of their panels.

Furthermore, the shrinkage values tabulated are average values with substantial ranges in individual samples. And more furthermore, these values are typically for drying from green to dry and not as you need- dry to more or less drier.

Bottom line- you don't have useful data to judge equivalent shrinkage but it doesn't matter because it is irrelevant. If the panel is held in place then the concern is even more irrelevant.

Re: Resawn veneer backer

#3

Ellis Walentine

Not to worry

Ellis Walentine

>It's the glue line that counts. Back in my contract furniture days, we laid up hundreds of thousands of square feet of flakeboard with veneer faces and kraft backer, and most of that stuff is still flat today. What you *don't* want is one-sided layups. The veneer itself isn't strong enough to bend the substrate, but the lack of a compensating glueline on the back is an invitation to trouble.

Ellis

Re: Resawn veneer backer

#4

I didn't know that

Bill Tindall

>that is, its the glue that causes the problem. Learn something every day on this forum

Re: Resawn veneer backer

#5

Me too.

Barry Irby

>

Re: Resawn veneer backer

#6

Re: I didn't know that

Larry in NW Ohio

>This is going to sound pretty dumb. In other words if a person could fasten a veneer down without glue then you would not have to put anything on the other side. Larry

Re: Resawn veneer backer

#7

Right

Mark Mandell - Gone Round In Jersey

>But only fairly silly.

Much has to do with changes in moisture content. The glue layer tends to seal one surface while the other is free to pull water vapor out of the air. Thus one side swells and contracts while the veneered side is artificially stabilized. Result is bowing and cupping. Same thing happens with mica laminating. Doors must be laminated on both sides (at least with a "backer" sheet) or the doors will warp. Mica, of course makes things even worse because the applied material is impermeable to water as well.

Re: Resawn veneer backer

#8

I agree with this

Keith Newton------WebKitFormBoundaryV6MZb+tiOpocz6

>Back when I was first learning about veneering, the book was instructing how to iron on with hide glue, which had a lot of shrinkage. With that method, keeping it balanced was essential.

Some people may not realize that hide glue is what was used to make glue-chip glass. This is a process where they spread an even film of glue on the face of the glass, then when it dries, the tension pulls the face of the glass off, leaving a nice feather pattern.

Any glue which is water base will swell the veneer and face of the substrate when it gets laid, then as it dries, will forever-after be trying to shrink. THis is why I like using epoxy. There is no water nor anything else that evaporates, thus no contraction.

While I don't do it a lot, I have veneered only one side, and sealed the other with epoxy, with no problems from any of it.

Re: Resawn veneer backer

#9

what about plastic laminate

John Lucas

>I've built 2 router tables and both times I glued the Formica to both sides to keep the table flat. Is this necessary? I think it is because I made some table saw inserts and only but formica on one side and 2 of them have warped a little. I seem to remember the last time I did that I put formica on both sided but that was so long ago and I wasn't as picky as I am now.

Re: Resawn veneer backer

#10

Samo, John

Mark Mandell - Gone Round In Jersey

>

Re: Resawn veneer backer

#11

Re: Resawn veneer backer

jesse cloud

>Agree with advice above - don't worry about matching species other than for looks. Also, its wise to put the backer on at the same time you put the veneer/glue on. I put some veneer on 1/2 mdf one sided and you could watch it warp as soon as I took it out of the vacuum press.

Historically, tabletops were often finished, but the bottoms left bare. Look under some genuine Stickley sometime. If the piece is held down mechanically with screws or other fasteners, you can get away with that.

For a router table that needs to be dead flat, I would always seal both sides.

Re: Resawn veneer backer

#12

Re: what about plastic laminate

Fred Davis

>The High Pressure Plastic companies make a neutral color without pattern Backer board for things like office furniture,desks,Tables and large flat surfaces specifically for compensating the top plastic and avoiding cupping of the surface.

This is much cheaper obviously then using the Finish plastic on both sides.

FredD