Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

quick release band saw tensioner

Posts

quick release band saw tensioner

#1

quick release band saw tensioner

jared

>Hello I have been making a lot of bandsawn boxes lately it seems. I got tired of turning the knob for the blade tension all thetime so looked in the catalog for one of those quick release outfits made by Carter etc. After seeing the price $150 plus shipping I was thinking of making my own, it cant amount to too much. Has anyone made their own quick release mechanism, any ideas or advice on this? Thanks in advance Jared

Re: quick release band saw tensioner

#2

Clint Searl

Re: quick release band saw tensioner

Clint Searl

>The blade can remain fully tensioned all the time without causing trauma to the machine.

Clint

Re: quick release band saw tensioner

#3

Re: quick release band saw tensioner

Barry Irby

>I tend to agree with Clint. Having said that, I bought one of the blade release gadgets. The Carter one. Paid too much for it. Seldom release the tension. It is useful when you need to change the blade.

One of the magazines and a Shop Tip or some such thing about making one of your own. I was amazed at how simple it was. If I had seen that first, I would have made one and never spent the money. I don't know which mag it was, but it had to be Fine Wood Working or the Wood Craft one, I think.

It was all wood and used a simple lever.

Re: quick release band saw tensioner

#4

William Falberg

Re: quick release band saw tensioner

William Falberg

>They're not really very difficult to make at all and you could look at the Jet lever tensioner for inspiration; just Google "bandsaw tensioning lever" images. It could be done as easily with 1/4" aluminum plate. You'd need to buy a drill and a jig saw, however. The hardest part is getting the getting the lever to stop "just" past the top of the cam. Make that part adjustable if you can; it saves experimenting with hole location. I say do it, do it, do it! The worst that can happen is you'll have some fun in the shop. A little metal working know-how would do woodworkers a world of good in the area of jig-making in general. There's only a few cheap tricks between most woodworkers and complete proficiency with aluminum and I highly recommend learning them.

Re: quick release band saw tensioner

#5

Re: quick release band saw tensioner

Mark Mandell - Gone Round In Jersey

>Jared,

Check the WC Articles section. Assuming you have a 14" saw, I seem to remember a DIY solution on this.

I'll (respectfully) disagree with Clint on the "need" for de-tensioning a band saw blade. BS blades heat & stretch, then cool & shrink much the same as chain saws (I de-tension them as well); any weakness in the blade (weld or links) will be amplified and the BS blade's gullets' geometry will be altered. Keeping tension on a blade also "tends" to push the tires out of round producing that thumping sound until they readjust. My saw (JET 18") is still doing fine on the original tires after 10 years of use. Both Jet and Suffolk Machinery (Timberwolf Blades) say to take most (but not all) tension off the blade at the end of a session.

Re: quick release band saw tensioner

#6

Re: quick release band saw tensioner

Fred Davis

>"Both Jet and Suffolk Machinery (Timberwolf Blades) say to take most (but not all) tension off the blade at the end of a session."

This is why Carters Quick release has two positions in addition to really loose.

I got mine when they weren't all that expensive, but I fully agree to use one ,if for no other reason then the precise repeatability of the tensioning once you have it set.

FredD

Re: quick release band saw tensioner

#7

Re: quick release band saw tensioner

john lucas

>I'll go to the shop in a little bit and see if I still have the plans I saved. I don't remember where I got them, possibly shop notes magazine but I'm not sure. All it amounted to was a lever that lifts the tension and then a block drops or fits into place. That part I don't remember exactly. I'll get back with you.

I had looked at the cam action ones like Jet uses and was going to build one of those before I found this one. Hope I still have it.

Re: quick release band saw tensioner

#8

found it.

john lucas

>It was in Woodsmith but I don't know which issue. Here's a photo. I copied the whole page and can send it to you if you want to send me an e-mail.

The pictures should explain it. The lever swivels out as you detension the blade so the lift block slides off the platform. There are two nuts and a washer set above the lever. Personally I would put a piece of steel or heavy washer glued to the wood to help protect it.

Set the lever in the tension mode and then adjust the tension for that particular blade. The you can simply de-tension by lifting the handle and sliding it off. How simple can you get. Credit for this brilliant idea should go to Bill Esposito from Ridge, New Hampshire


img

Re: quick release band saw tensioner

#9

Re: quick release band saw tensioner

Chuck in ND

>The JET 14" now has the quick release, I have the older JET ( still cream colored ) that does not have the quick release. I looked into just buying the parts, which didn't seem too bad but I'd have to drill a couple holes in the cast iron and tap them, I think the Grizzly mod is that way also. I'm not so sure that I want to go that route. The Carter isn't in my budget, and the homemade wooden model while functional, also isn't exactly the best looking accessory I've ever seen, so I just do without. But after bending a upper axle a few years ago, I now detension the blade at the end of the day religously. Maybe someday I'll attempt a version of the homemade wooden one, but with metal instead. Times are tough here, I've been out of work for sometime allready, and I'm loseing steam.

Re: quick release band saw tensioner

#10

William Falberg

Re: quick release band saw tensioner

William Falberg

>I like this one better:

http://lumberjocks.com/Blake/blog/3381

from Blake Weber

Re: quick release band saw tensioner

#11

thanks

jared

>Thanks for the replies. I intend to build one similar to the one pictured, with a few modifications. It shouldnt take too long and it looks like it is completely functional. Jared

Re: quick release band saw tensioner

#12

Re: thanks

john lucas

>I'm almost through building the one I sent. I turned the handle a little because I'm a woodturner and that's what we do. If I'm not to tired I still have to turn the knob for the new top adjustment arm. I made an L shaped arm t make it easier to adjust and need to turn the knob and put a screw through it and I'll be done. I got hungry and decided to feed my face first. I'll post a photo.

Re: quick release band saw tensioner

#13

here is my version

john lucas

>I was worried that it would be in the way since it extends past the bandsaw. My bandsaw has a riser block and the angle of the arm makes it stick up beyond 6 feet so it will definitely out of my way and probably out of reach of most of the people who visit my shop.

It seems to work perfectly.


img

Re: quick release band saw tensioner

#14

Re: here is my version

Larry in NW Ohio

>John I`m was totaly diappointed when I opened your post and saw a picture of your bandsaw. After reading your last post I was expecting to see you feeding your face{:-)))) Larry

Re: quick release band saw tensioner

#15

ebd

Re: quick release band saw tensioner

ebd

>Are you nuts? It doesn't hurt the bandsaw, but it definitely hurts the performance and life of the blade. If all you are doing is crude cuts, I'll agree with you. If you are making precision cuts or resawing for veneer or turning thins, for example, I'd say you are dead wrong. Not only won't you get acceptable cuts, but when doing that kind of work you tend to buy premium blades. Leaving tension at full would be like using a fine talesaw blade (for example a Forest) to cut plywood. I ain't gonna' do that.

That said, I've heard that the tensioner doesn't allow you to ignore proper tensioning each time it's used. That's the reason I haven't bought one. If I've got to make the fine adjustment every time then what's the point? Once you get used to the flutter method it's quick and easy. If I was going to invest in anything it would be a crank of some kind for the tensioning knob. That would really speed things up.

Re: quick release band saw tensioner

#16

Re: Glad that you pointed this out

North of the Border

>I agree the Carter gadget is a little too much on the dollar but that doesn't mean keeping the blade tensioned at all time is correct. If it were, the Carter's invention would never have left the drawing board.