Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Find a woodworking club near you

Question on Performax Sand paper

Posts

Question on Performax Sand paper

#1

Question on Performax Sand paper

Barry Irby

>I have ruined several strips of sand paper for my Performax. The end tears off.

Does anyone have a good way to repair them?

PS, I learned something. If the paper strip is loose, it bunches up at the end near the motor. The Spring clip does not pull it tight. It wrinkles and wears through and tears. So, When you install the paper, keep it tight and neat. Put it on, run it for a minute or two and then tighten the paper again. Seems to really help.

Re: Question on Performax Sand paper

#2

Re: Question on Performax Sand paper *LINK*

jesse cloud

>I don't have a way to mend the broken roll (hope someone does), but here's a link to a cool gadget that helps you apply the spring at the right time. Seems a little pricey for a piece of bent wire, but definitely worth it.


cool gadget

Re: Question on Performax Sand paper

#3

Re: Question on Performax Sand paper

Carol Reed - home in Strawberry

>I got that thing with my machine. How the heck do you use it? Are there instructions, preferably with pictures, someplace?

As for tearing off the end of the roll, I don't have a fix either. Keep it tensioned properly to avoid this. Use the ruined strip at the lathe. I don't know!

Re: Question on Performax Sand paper

#4

Re: Question on Performax Sand paper

E.Taylor

>That little �bent wire� tool came with my Performax.

Call Jet/Performax and see if they will comp you one. Won�t cost anything to try.

I believe a little experimenting will reveal how to use it.

Catch the hooked end in the hole in the arm of the spring loaded clip and pull up to pinch the sand paper between the �bent wire� and the drum. Leave it there as the spring tension will hold the paper as you fish the end of the sand paper thru the slot in the spring loaded clip. Once the paper end is in the slot, take up any slack and release the tension. It�s easier than my crude explanation makes it seem.

Also, I've repaired the ragged ends with duct tape. Not the best, but gives you a little more mileage.

Re: Question on Performax Sand paper

#5

Re: Question on Performax Sand paper

Dick Stariha

>My motor end tension clamp quit "clamping". My solution was to whittle a tapered wooden thingie so I could wedge and lock the end of the s paper strip. Cut it flush with the drum and it works fine.

Dick S

Re: Question on Performax Sand paper

#6

Re: Question on Performax Sand paper

Carol Reed - home in Strawberry

>Another question.

Which end do you begin loading the paper and why? Is there an advantage to loading from the outboard end to the motor end as opposed to the other way around?

Re: Question on Performax Sand paper

#7

Thanks Carol

Dustmaker Mike

>I don't feel so bad now. I have been trying to figure out that little bent thing since I got my sander. Now you are asking the same questions I have about how to load the sandpaper(-; Mike getting to make a lot of dust of the next few weeks.

Re: Question on Performax Sand paper

#8

Loading Paper

Ken Krawford

>I believe the instructions say to start from the left side of the drum (as you are facing the infeed side of the sander) and work to the right. The reason is that the left side only has a clamp while the clamp on the right side will slightly tension the paper as you release it.

IMO it is a flawed system as I have also ruined paper due to incomplete tensioning.

Re: Question on Performax Sand paper

#9

Sharing some of what I know......

Barry Irby

>Start lading the paper on the end away from the motor. That clip just clamps the end of the paper and does not mention it. Also, the paper tends to wrap itself tighter and spiral the slack over toward the motor. I find it useful to carefully fold a crease in the strip Where it enters the hole/slot in the drum. Pick the point where the strip is about 3/4" wide and fold it under and keep the edges parallel so that the crest is at right angles to the edge. Put the crease right at the opening and insert the strip in the clip.

On the motor end, I put the crease about a 1/4" short of the opening so that as the clip pulls and takes up the slack the crease will come to the edge of the opening.

I have repaired a strip with the nylon reinforced tape. I stuck it to the back of the sandpaper and then fold it back on itself to cover he sticky surface. I put it on and then wrapped a trip all the way around the drum on top of the sandpaper to keep the end from flying loose. It worked, but it "cost" me about an inch of the width of the sander.

The motor end is under tension. I think some really good tape would let you splice a piece on the end. My tape is old and tired. Wonder if CA glue would help it. Some sort of really thin but non stretch fabric would work with CA.

I don't have the clip.

Re: Question on Performax Sand paper

#10

Re: Question on Performax Sand paper

Robert R. Clough - Thorncraft

>The only advice I can add here is - take it slow and careful when wrapping the paper/cloth. Make sure there are no overlaps. Get the right end as tight as possible BUT run the machine and re-tighten at least twice.

I understand the reason for working inboard rather than outboard has to do with the rotational direction of the drum. The paper tightens from L to R. Were the drum to rotate the other way, the paper would tighten from R to L.

Re: Question on Performax Sand paper

#11

Re: Question on Performax Sand paper

Larry in NW Ohio

>Carol I have a woodmaster but basically they are the same paper wise. They wrap the paper from right to left from the back side is it keeps the paper tight, if it would be done the other way it would just unwrap the paper. If you look at it and turn it by hand you can see what I`m trying to say. Larry

Re: Question on Performax Sand paper

#12

Re: Question on Performax Sand paper

Dave Paine

>I have only ripped one strip I can remember, and this was due to an unevn board so started fine, but later the board was too thick, resulting in heat and overload.

I would not be confident in any tape behind the strip to hold up to normal tension. Good luck. Sucess will depend a lot on the tape used. Maybe the carpet tape which requires heat to set the glue. Should be strong enough. Gets lots of pressure in normal carpet use.

I recently switched to the Klingspor blue Zirconia paper. Major difference. I used to get build up on the rust coloured strips, also from Klingspor.

Finally getting full use out of the strip. Several weeks and easily cleaned up with abrasive rubber cleaner. Expect this to be the first strip to be replaced due to dulling before clogging up.

I have not thought much about which end. I think I start at the motor end since it is a pain, but thinking about the other replies, starting at the end under tension, the end opposite to the motor makes sense.

Re: Question on Performax Sand paper

#13

Re: Question on Performax Sand paper

Frank

>Howdy

I have a 22x44 Jet and I just watch the end and when it starts to look bad I will just turn the sand paper around 180'y. If you lose the end then you will just have a long roll of sand paper and after a few bad rolls that won't fit on the sander they almost trun in to trash, $$$ trash. So I just watch that working end...

Frank