Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Hot (Warm) finishing?

Posts

Hot (Warm) finishing?

#1

JL

Hot (Warm) finishing?

JL

>Recognizing that it is inherently dangerous...

Has anyone ever warmed or heated finishes to improve flow characteristics? It is getting colder outside and it is more difficult to finish things.

One of the guys who instructs over at JCCFS was touting the praises of hot finishes. He makes the standard BLO/Poly/Mineral Spirits mix and heats it up before applying it. I realize that the warmer you get such a mixture, the quicker the mineral spirits will evaporate and that you will have more combustible vapor in the air - this makes the process quite hazardous both physically and in terms of health. If I were to do it, I would prefer to be wearing a respirator and far away from any ignition sources.

I can see that the viscosity would be less. I can also see that there might be quicker oxidation of the BLO. I can see that the mineral spirits would go away more quickly.

Has anyone ever done "hot finishing"? Do you think the benefits outweigh the risks?

Re: Hot (Warm) finishing?

#2

Clint Searl

Re: Hot (Warm) finishing?

Clint Searl

>You know that if the guy is familiar with the BLO/poly/spirits magic potion, he must be a finishing expert, so ya gotta follow his advice.

Actually the BLO adds nothing to the formulation, although reducing the poly with spirits or naptha can be worthwhile to enhance flow or make a wipe-on finish. Short of going to the point of polymerization, heating the mixture is worthless.

Clint

Re: Hot (Warm) finishing?

#3

Done That

Mark Mandell - Gone Round In Jersey

>But only outside. Helped build a playground and carved an 8' globe. I then applied hot (steamin') oil finish/stain with blue and/or green pigment added to oceans and continents. Heated the stuff on an electric hot plate (no flames here, please!!!). Got penetration of the color close to 1/4" into face grain of treated SYP. Waited 24 hours, then applied "witches brew" of oil varnish+soy+MS (linseed promotes mildew so not for outside) also heated to 110�. Amazing how the wood sucked that stuff in.

Yes, I did wear a vapor mask as well as a face shield. Applied with a 6" brush.

No, I would not do this inside under ANY circumstances.

mm

Re: Hot (Warm) finishing?

#4

alternative ways to achieve the same result

Bill Tindall, E.TN

>Now days finishes are formulated with high solids to meet EPA requirements and they are typically too thick to brush well. Heating works but adding some mineral spirits or naptha accomplishes the same effect. Because the finish cools almost instantly I doubt there is any increase in cure rate. Personally, the idea of heating a solvent indoors seems like a poor idea so i thin.

Re: Hot (Warm) finishing?

#5

Re: Done That

Larry in NW Ohio

>I`m curious about something. I`ve read that people do BLO finishing. I`ve never heard this before a few months ago, maybe years. What is involved in this? Is it just putting it on with a spray gun? I know it sounds kind of dumb, bit I never heard this before I came to this wonderful place called WC. Of course I learnd a lot since I came here. Thank You Larry

Re: Hot (Warm) finishing?

#6

BLO

Mark Mandell - Gone Round In Jersey

>Larry,

If you're asking about straight BLO application or its variant, "Danish" oil, I use Watco (BLO+) oil to pop grain on some woods like Cherry, and it's a 1/3 ingredient in traditional Witches' Brew along with oil poly and MS that is a wipe-on/wipe-off finish for interior furniture and wood projects.

If my assumption is correct, I've never heard of it being sprayed as there is no benefit; it would simply create runs and drips.

I learned the hard way, however, that linseed doesn't do well outside because it turns black with mold in fairly short order. I (with my "superior woodworking knowledge") made the mistake of adding it to an oil finish for my deck, and had to powerwash it all off 6 months later.

Re: Hot (Warm) finishing?

#7

Re: Hot (Warm) finishing?

Larry Clinton At Frankfort (Central)., Indiana

>The only finish I have seen sprayed "hot" was lacquer. This was done at Carr Cabinet in Frankfort Indiana. I worked there when I was about 18 years old (50 years ago). Don't know of the practical benefits, wasn't involved in the spray line at the time. I always thought it was heated to reduce the viscosity allowing a heavier coat to be applied so the finish required less coats. A side benefit was that the coating was dry to the touch in just a few seconds. This was a commercial cabinet shop which produced hundreds of cabinets a day.