Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Executing 35 degree lap joint

Posts

Executing 35 degree lap joint

#1

Executing 35 degree lap joint

Dan Mitchell

>I'm building the coffee table shown in the drawing below out of walnut. I have the top & legs completed, and am now puzzling out how to cut the center lap joint for the stretchers which attach to the legs. The stretchers are ~ 1.5"W x 2.25"H x 38"L, and meet at approximately 35 degrees. I would like to use a dado blade in the TS to cut the joints, but the 35 degree angle exceeds the maximum of my Osborne miter gauge, so I guess I'm going to have to fabricate some type of jig. Alternatively, I could probably use a router. Any suggestions on these or an alternate approach? the rest of the table has come out well, and the walnut wasn't cheap, so I really don't want to screw things up at this late stage.

TIA

Dan


img

Re: Executing 35 degree lap joint

#2

Clint Searl

Why not by hand?

Clint Searl

>

Re: Executing 35 degree lap joint

#3

Ellis Walentine

I agree with Clint

Ellis Walentine

>The layout shouldn't be difficult. Use a tenon saw and cut the joints by hand, cleaning up with chisels.

Ellis

Re: Executing 35 degree lap joint

#4

Have neither the tools, nor the skill

Dan Mitchell

>

Re: Executing 35 degree lap joint

#5

Ellis is right, and you can do it...

Bruce, a MN Galoot

>For starters, get yourself a clamp and a piece of wood, say, 2" X 2" X 8" long. Put one crosspiece exactly in position and clamp the 2 X 8 against the side of that crosspiece. That becomes your saw guide. Saw carefully straight down. The guide will keep your saw straight and perpendicular. Now put the crosspiece back in position and clamp it against the other crosspiece. Move the guide to the other side of the top crosspiece and clamp again. Now saw down carefully. Remove the wood you have liberated and you will find that it exactly matches the thickness of the crosspiece. Repeat for the other one. This works really well. This is not theory. I've done it.

Re: Executing 35 degree lap joint

#6

Re: Ellis is right, and you can do it...

Dan Mitchell

>Thanks for the reply Bruce, but I'm afraid I'm not following you.

Dan

Re: Executing 35 degree lap joint

#7

Make a practise joint first...

Hamish

>Dan,

If I were you, I would make up a mock-up first to size from some scrap stock and then practise cutting the joint. This ought to give you some more confidence before tackling your coffee table. Good luck.

Hamish.

Re: Executing 35 degree lap joint

#8

Ellis Walentine

Challenge yourself

Ellis Walentine

>Believe me, it isn't difficult, and if it doesn't come out perfectly, it'll still function well and look okay. This entire thing is hidden by your table top, right?

For layout, do you have a bevel gauge and a combination square? A marking knife? (If not, a pencil will be fine.) As for a hand saw, practically any type will do for four little cuts. If you have trouble following a straight line with your saw, practice a bit on scrap pieces first.

These cutouts don't need to have a perfectly square, flat bottom. It isn't seen and doesn't matter. Just try to cut the notches a little snug at first, then if the fit is too tight, clean up your saw cuts with a sharp chisel.

Take my word for it: it just isn't difficult and it shouldn't be daunting. That's what this forum is for -- to help.

Go for it.

Ellis

Re: Executing 35 degree lap joint

#9

Re: Challenge yourself

Jerry Gibbs

>secret to clean up is sharp chisel. Jerry Gibbs

Re: Executing 35 degree lap joint

#10

Most Important Step

Kneale Brownson..Packing for return to CO snows

>The practice joint on scrap will give you the understanding you need to attack the real project with confidence.

If you've made the curved legs and completed the M&T joints needed to connect them with the aprons, you've got all the skills you need for this simple half-lap.

Re: Executing 35 degree lap joint

#11

Re: Executing 35 degree lap joint

Tony - Memphis

>I would do it by hand myself, but I have built jigs for similar situations. Even then, I do the final fitting of the joint with a chisel. I made a TS sled and just attached a fence at whatever angle it was that I needed. That works pretty well. Let us know what you do and ho wit works out. Good luck with it.

Tony

Re: Executing 35 degree lap joint

#12

Chet Kloss

You can do it!!!!!

Chet Kloss

>

Re: Executing 35 degree lap joint

#13

I agree with those Above, but........

Barry Irby

>If you find trying this by hand I can think of several ways to do it.

Actually, you could cut this with a hack saw and clean it up with a chisel.

Don't want to do it that way? You could add an auxiliary angle to your miter sled. Cut a wedge and fasten it to your miter guide. This will increase the angle you can cut. Add something like a thirty degree angle. Add a long fence. Draw the angle you need on a couple of practice pieces and cut them. See if they work. Fiddle with it until you get the angle and depth right. Then cut the actual pieces.

You could also make up a router jig that would do the same thing.

Re: Executing 35 degree lap joint

#14

Re: Executing 35 degree lap joint

Stephen Kirk in Quakertown PA

>Gotta agree that doing something like this by hand is really quite easy. The practice joint idea is probably a must. You do want a decently sharp chisel, though. Probably won't take more than a few minutes and it'll add another good skill. If you want, you could use it as an excuse to buy a router plane.

A router would also work quite well. Just lay out your joints, both sides and depth. Set a straight edge along each line. Chuck a bottom bearing flush trim bit in, set the depth and rout away. it's best to clamp some sacrificial boards on either side of your cut as the router will blow out on you otherwise.

As Ellis said, if you wont see it, extreme precision is really not necessary.

Oh, I've done joints like this using both hand saw and router. I hand saw down my edges to the depth I want. The come back in with a router and free hand rout out the waste up close to my cut line - leaving as little wood as I dare. Then you come back with a chisel and pop out the little slivers.

Re: Executing 35 degree lap joint

#15

This will take two postings,

Bruce, a MN Galoot

>here is how you lay it out:


img

Re: Executing 35 degree lap joint

#16

and two

Bruce, a MN Galoot

>saw out the waste between the two blocks. Cut to half the thickness of the crosspiece and repeat on the other crosspiece.


img

Re: Executing 35 degree lap joint

#17

Re: Executing 35 degree lap joint

Dan Mitchell

>"Oh, I've done joints like this using both hand saw and router. I hand saw down my edges to the depth I want. The come back in with a router and free hand rout out the waste up close to my cut line - leaving as little wood as I dare. Then you come back with a chisel and pop out the little slivers."

This approach sounds like a winner. It's not cutting the sides that concerns me, it's removing the waste.

Thanks all for the replies. I guess I'm just a little nervous about hosing the thing at the last minute ;-)

Dan

Re: Executing 35 degree lap joint

#18

Re: and two

Dan Mitchell

>So you're pressing the side of the saw blade against the clamped on blocks to act as a guide + help keep the blade verticle?

Thanks for posting the pics Bruce.

Dan

Re: Executing 35 degree lap joint

#19

that's right

Bruce, a MN Galoot

>you can get a nearly exact fit following that guide. You might need to pare a little but precious little if any.

Re: Executing 35 degree lap joint

#20

Re: Executing 35 degree lap joint

Stephen Kirk in Quakertown PA

>Heh, it's perfectly fine to grab some scrap sized to the same dimensions and use that to set up the cut. No need to take risks on finished pieces. Especially doing some free hand routing - it's good to know how the bit will cut and move in the wood. If you are doing a deep cut, definitely make a couple of shallow passes - it's easier to control. Some scrap boards clamped on either side is important as you'll blow out the sides when you rout cross grain.

Even if you don't cut these joints by hand, it's a good time to try one out so you'll be ready the next time. Even a little accuracy with a hand saw can go a long way to freeing you up from making lots of complex jigs and such. Plus it's an excuse to buy more tools, cuz you'll want 2-3 good saws, router plane, shoulder plane, float, etc etc etc ... !!!

Re: Executing 35 degree lap joint

#21

Re: and two

Stephen Kirk in Quakertown PA

>That's a neat and easy way to do it. I'll have to keep that in mind. Work well when routing with a pattern bit too. Should be dead on perfect. Really good for keeping a hand saw vertical too. Sometimes the simplest is the best.

Re: Executing 35 degree lap joint

#22

Re: Executing 35 degree lap joint

Jim Dillon

>Dan,

And if you are worried about your chisel skills, you can use the wooden guides as Bruce suggested to maintain vertical on the chisel. Just make the initial slot a tad narrow, as Ellis suggested, then sneak up on the exact fit with the chisel held against the guide. A guide for maintaining vertical is sometiimes used when cutting dovetails, so you've learned a new skill.

Jim

Re: Executing 35 degree lap joint

#24

Re: Executing 35 degree lap joint

Dan Mitchell

>Frank - My shop's pretty complete, but I don't have one of those Dinosaurs! ;-) I do have a SCMS, but of course, it won't do dados.

Actually, given the length of the piece (38") and the angle, and the fact that the cut is in the center, I'm not too sure you could do it on one, anyway. I guess you could rotate the head into "rip" position & come up with some kind of jug to hold the piece as you slide it past (scary!) , but I think by that time, you've pretty much left "piece of cake" territory"! ;-)

Thanks for the reply.

Dan

Re: Executing 35 degree lap joint

#25

Jason Roehl in Lafayette, IN

SCMS?

Jason Roehl in Lafayette, IN

>Cut a wedge for an auxiliary fence, set your depth stop on the SCMS, lay out as described in other posts with a pencil or marking knife, then nibble away with the SCMS between the marks. A chisel or rasp to clean up the bottom of the notch.

Jason