Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Adhering Paneling to masonry wall

Posts

Adhering Paneling to masonry wall

#1

Adhering Paneling to masonry wall

Ben Ragusa, S. Jersey

>Good Morning.

As part of a project to construct built-in mudroom cabinets, I need to attach bead board paneling to a brick wall which has a smooth plaster surface. There is no wood to nail or screw into. Having no experience with construction adhesive, I am seeking your advice. The construction adhesive label says it needs to cure for 24 hours, so I am trying to come up with way to hold the panels in place while the adhesive dries. I have two ideas- one is to cut strips off a 2x4 and flex them accross the room (it's only about 6 feet wide). The other idea is to temporarily use tapcon screws to hold cauls to the wall, then remove the screws and fill any holes not covered by moldings. What would you recommend? Any other ideas?

Re: Adhering Paneling to masonry wall

#2

Re: Adhering Paneling to masonry wall

Larry in NW Ohio

>Ben There is a caulking that is made just for this problem. It`s called "Power Grab" and made by Loctite. You put it on and it`ll pretty much take ahold right away.I have used it and it does take ahold very quickly. Good Luck Larry

Re: Adhering Paneling to masonry wall

#3

Re: Adhering Paneling to masonry wall

Justin Szeliga

>Hi Ben- Firstly, you're gluing to whatever is the top layer, which I assume to be paint on the plaster over the brick. So any weakness in the paint to plaster layer will allow the paneling to eventually pull off the wall when the panel moves as a result of expansion & contraction, which in a mudroom I will assume to be higher than normal.

The best solution is to attach wood sleepers to the plaster, then nail to the wood. I am guessing this isn't a good idea because you probably don't want to lose the space the sleepers would take up, but that is the best option. The easiest way to glue the panels right to the masonry is to Tapcon them up w/glue, the Tapcons acting as clamps for the initial set & holding things in one plane in the future, The screw ends can be filed w/putty & painted.

Peace

Justin

Re: Adhering Paneling to masonry wall

#4

Re: Adhering Paneling to masonry wall

Thomas Skaggs, Foothills of Mount Level

>This might be an opportunity to further insulate and separate the paneling from any potential moisture. You might consider attaching vertical strips of 2X2 material and put styrofoam insulation between the strips. Then attach the beadboard to the strips.

Just an idea.

Tom

Re: Adhering Paneling to masonry wall

#5

Re: Adhering Paneling to masonry wall

Clint Searl, at the base of Haycock Mtn

>Don't sweat it or overwork the problem. Run beads of PL Polyurethane Construction Adhesive about 8" apart vertically. Use a few bow sticks, per your idea, to hold the panels in place overnight, and you'll be good to go. They won't fall down.

Clint

Re: Adhering Paneling to masonry wall

#6

Re: Adhering Paneling to masonry wall

Fred Davis

>Ben,

assuming your bead board is ply panels there is no worry about movement from any MC change in the room.

Using PL adhesive like Clint says is a winner and one additional step, after you apply heavy beads of the adhesive , mash the panel in place and then pull it back for a minute or two.

When you replace the panel , it will grab with more force then you thought possible.

If the PL 500 odor is objectionable, use PolySeamSeal , 11oz. caulking tubes and is equably fast and effective, plus it cleans up with water.

Either product will destroy the beadboard if you at a later date ,want to remove it in the same size pieces you used the first time. ;-))

FredD

Re: Adhering Paneling to masonry wall

#7

Thanks to all, and the plan

Ben Ragusa, S. Jersey

>Thank you all for you advice.

I'm gonna go with simply sticking it to the wall with the PL adhesive and bracing it. The thoughts on insulating are appreciated, but sadly, the loss of an inch or two complicates an already tight space.