Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Table saw - How to get blade parallel to mitre?

Posts

Table saw - How to get blade parallel to mitre?

#1

Table saw - How to get blade parallel to mitre?

Pete

>Hey all you wise folks,

You might recall that I am the guy that was asking your opinion of a used Grizzly G1023. Well, I picked it up for $275, replaced the switch, and cleaned up the rusty top. Thanks you all for your advice. I know I have said that before, but I really do appreciate it.

The caliper I ordered just arrived, and I am trying to get the blade really accurate. However, even after loosening the table top, and adjusting it as far as I can, I am still nearly 1/8th out. I've looked for the kind of internal adjustment that my old (piece of junk) saw had. Go joy. Hoping someone could point me in the right direction.

I looked at the manual, here:

http://grizzly.com/images/manuals/g1023_m.pdf

And the parts list, here:

http://grizzly.com/images/partslists/g1023_pl.pdf

And I just don't know where to apply the wrench. As always, your help is greatly appreciated.

Thanks,

Pete

Re: Table saw - How to get blade parallel to mitre?

#2

Re: Table saw - How to get blade parallel to mitre

Virgil Johnson

>It's not a matter of applying the wrench. Its a matter of applying the mallet. Loosen the bolts that hold table top in place and whack the table in the direction it needs to go.

Re: Table saw - How to get blade parallel to mitre?

#3

Re: Table saw - How to get blade parallel to mitre

Fred Davis

>Assuming your top is using a bolt at each corner to hold it to the cabinet , I find that instead of backing off all four bolts , determine which direction it needs to move in order to parallel the mitre slot and then loosen Three bolts , leaving one for top to pivot on.

This isn't rocket science , but I suppose the saw could have been damaged enough , that the previous owner had the same problem your experiencing.

Classic example of what to look for in a used saw Before you buy it.

If all else fails , get a Machinist or Millwright to check it out.

FredD

Re: Table saw - How to get blade parallel to mitre?

#4

Re: In my case...

DaleLenz

>it's tapping the motor bracket while it is loose.

Re: Table saw - How to get blade parallel to mitre?

#5

I have already moved the table

Pete

>I loosened all bolts on the table and rotated it as far as I can. I am still 1/8th inch out of true. What do I adjust under the table?

Thanks!

Re: Table saw - How to get blade parallel to mitre?

#6

Re: I have already moved the table

Virgil Johnson

>I looked at the instructions (again) and possibly the trunnion has been shifted in one direction to the extent the clearance holes will allow instead of being centered. Pull the top completely off and take one of the trunnion bolts out to check. There is nothing to adjust other than shifting the table top.

Re: Table saw - How to get blade parallel to mitre?

#7

Re: Table saw - How to get blade parallel to mitre

Robin Corell in Atascadero CA

>while you are trueing the blade allignment it would also be a good idea to tilt the blade to 45* and check. It is possible for a table to be true at 90* and be out when tilted. Fixing this will involve moving shims under the trunions. If your allignment is out when tilted and true at 90* comback and ask for more info if call Grizzly for instructions.

Robin

Re: Table saw - How to get blade parallel to mitre?

#8

Great point. Thanks

Pete

>

Re: Table saw - How to get blade parallel to mitre?

#9

Re: Table saw - How to get blade parallel to mitre

Ben Ragusa, S. Jersey

>Hi Pete,

Maybe you got this sorted out by now, but in case not, I noticed something interesting in the manual. There is a section for Blade Alignment:

The blade position can be adjusted slightly in

case it contacts the table insert when raised. To

adjust the blade position:

1. Remove the table and wings and set them

aside.

2. Loosen the blade adjustment bolt. Figure

30.

3. Shift the geared bearing housing in the

appropriate direction. WARNING: This

adjustment should not exceed 1⁄16". Over

adjustment will cause the blade to hit internal

parts of the saw.

Did you check this adjustment?