We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
Well, the wedding is now over and our friends are off on their honeymoon. The cupcake stands were a hit with several at the wedding. The white dyed birdseye Maple veneer was a near perfect match with the icing on the cupcakes which was an added benefit. I'm just glad that this project is over and was very well accepted. Here are the stands:
Here is a closer shot of the white dyed veneer that I put on the faces of each stand.
A shot from the front of the stands.
A view of how they looked in use at the wedding.
In short, I learned a LOT about veneer work on this project and I want to thank Mark Cothren and Joe Meazle once again for helping out with maple wood and hardwood plywood on this project. It is friends like this that have helped me save money making the project as well as me getting this project done on time.
The finish is Zinnser's spay-on Clear Shellac.
This week I'm taking it a little easier and getting stuff done around the house that has fallen through the cracks due to the wedding.
That's it for me...so what did YOU do this past weekend??
>No woodworking for me this weekend. I celebrated my 75th birthday with a dinner party at one of my son's house in Scottsdale. All of the kids and grand-kids were there so it doesn't get much better than that.
>for my pink bathtub this weekend was "a time to destroy".
First I had to rip out the plastic liner.
Then I donned the face shield,earmuffs and gloves and took a few heavy whacks at the side of the tub. While the surface enamel crackled and the tub dented easily it became quickly apparent the tub wasn't going to give out in pieces with the sledge hammer. So I trotted downstairs and retrieved the sawzall. I made a cut down the middle of each side, then a slicing cut around the back end. A couple of pounds with the sledge hammer and the back end was free.
A few more whacks with the sledge hammer and voila!
The tub was done. Now the filler wall on the right had to go.
I think it looks BEAUTIFUL.Next the plumbers will remove the old pipes and replace with new stuff all the way to the basement
>With six friends I got the Stubby dismantled and moved up out of the basement and out to the garage [base is 450lbs]. Still have to run power and complete the air suspension mobility plate before I can start turning again.
This was the first time in almost 2 months that we've had 3 dry days in a row so I was able to finish sealing/staining the back deck (Penofin Oil). Followed that with power washing the patio pavers.
It was an Aleve morning!
Now the push shifts to inside to get ready for wedding (son) this Saturday.
Nice servers, Dennis. They'll likely get used often.
They are very nice looking plattens, very well done. I wondered what they would look like, and I like the look. Neat idea. I began milling up cherry to continue the current guest bedroom project. My #5 son visited from VA and showed me how to upload pix from my new digital camera into the computer. Had kabobs last night from the grill and my garden. Small dinner party. Have a great week, Dennis.
>It's a piece my wife inherited that I finished the restoration of a few months back. It's unique in my experience because the pilaster molding on the right side is hinged and has a functioning lock that engages the edges of the drawers to keep them closed.
It's solid oak and birds eye maple veneer. I stripped it and finished it with gloss NC lacquer, and installed new pulls.
I learnt this weekend that a very close friend at work was diagnosed with cancer, GBM Stage 4 brain tumour. He had surgery last week and starts radiation and chemo this week, Another survivour on the path to help.
Your thoughts and prayers for my buddy Joe will be appreciated.
Productive stuff, and a drive-by solicitation *LINK*
Ellis Walentine
> Hey, Dennis, nice cupcake stands. I don't think I've ever seen that type of stand before. The veneer work looks impeccable.
This weekend was a home improvement binge for me. LOML was painting her office, so I finally broke down and made a mantle for her little stone fireplace. I've been meaning to do that for thirty years, sorta like the towel rack I made last year. I used some black walnut from a log that I had milled recently. This log had grown for the past fifty or sixty years within sight of Candy's office, so it was a fitting choice for the mantle.
The tricky part of this project was scribing the front and return pieces of the mantle around the irregular stone chimney. In retrospect, I think I could have done it differently, but I did it the way I am accustomed. First I made up a little scriber -- a stick with a hole in it near the end for my pencil. Then I scribed each piece separately, before cutting either one to length or width. I had to clearance the rear underside edges to clear the mortar fillets where the stone mantle meets the chimney.
Since the parts were of different width, I decided on a long, unequal miter joint, about 40�/50� I'd say (didn't measure it). I cut off the end of the front at the 50� angle and then inched up on the roughly 40� complementary cut on the return. Once I had the pieces mating perfectly, I made a Krenov-style doweling jig and joined the parts with sections of 5/8" dowel. I would have used loose tenon joinery if I still had a horizontal mortising machine. I considered a Chinese-style, hand-sawn, through-tenoned miter, but that wouldn't have allowed me to sneak up on the angled fit the way I had to.
In retrospect, I could have glued the parts together with whatever joinery I wanted, then offered the assembled unit to the corner and used my scriber at a 45� angle to the chimney. In theory, it would have worked fine; in practice, I'm sure there were snakes in the grass. I know it would have been more sensitive to careful scribing.
Also on the home front, I cleaned up and serviced my lawn tractor -- new gas, oil and air filters, an oil change, checked the plug gaps, hosed off the dust, greased the tie rod ends, mower shivs, steering box, etc. Now all I need is some new blades to replace the ones I've beat to death with all the rocks and other hazards around our place. That's what happens when you live on Flint Hill.
Today, it's back to work. I'm still trying to get a programmer to work with me on a new forum package so we can archive all our old messages and move to a newer, more affordable server environment. These things take time. And money.
Speaking of which � I didn't mean for this to be a drive-by fund-raiser � if you haven't signed up for recurring donations yet, or helped out in some other way � and you would like to help out � now would be an excellent time. Our sponsors' advertising budgets have shrunk significantly this year, so I've got to rely more on your help to get us through the recession and pay for the upgrades and new initiatives that are on the wish list. We now offer an annual recurring donation, which saves quite a bit on PayPal transaction fees. Back in our pre-advertising days, I used to run spring and fall fund-raisers to help defray some of our expenses. Now, I may have to start that practice again, much as I'd rather not. I appreciate any and all assistance you see fit to lend to the cause. We still give a hat or t-shirt for annual contributions of $50 or more.
That's it. Thanks for listening, and thanks even more for helping to keep WoodCentral healthy and strong.
>Starting to clean the old mortar off some used blocks for a little storage shed I'm going to erect, and I hit my thumb with the hammer while holding the masonry chisel.