Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Dust Collection Questions *LINK*

Posts

Dust Collection Questions *LINK*

#1

Dust Collection Questions *LINK*

Andy Lincoln,in Dearborn,MI

>Hi All,

I have a 2 car garage sized shop .I usually work alone and one one machine at a time.Is a 1200cfm dust collector(non-cyclone) strong enough to handle most onf my needs? I plan to hook the table saw to one port and use the other port to run a line across the width of the garage(18ft) that would have a "y" that flex hose can move between the planer,jointer,or drum sander.it would then continue about 4ft and catch the sawdsut from the mitre saw.I plan to install blast gates at each location.If I was to eventually move the DC to an outdoor location how many feet of pipe will a 1200cfm,1 1/2HP dust collector support?

And do you think that buying a 2 month old Steel City DC with remote for $250 is worthy of a drive-by gloat??

Thanks,

Andy


Steel City Dust Collector

Re: Dust Collection Questions *LINK*

#2

Re: Dust Collection Questions

mdclor

>Andy,

In a previous shop, I used to have a Jet DC-650 which was great for 1 machine at a time. Once I did the same thing you are considering, i.e. running more flex tubing and adding wye's with blast gate closures, the air resistance caused by the extra tubing dropped the effectiveness of the unit to almost nothing. I finally took off the extra tubing and moved the DC to each machine as needed. As you can imagine, this got old in a hurry and prompted me to get a permanently installed cyclone. YMMV.

HTH,

Merle

Re: Dust Collection Questions *LINK*

#3

Re: Dust Collection Questions

Barry Irby

>I have a Delta DC with a 1 1/2hp motor that is about 1100 or 1200 cfm. I have a one car garage (14' x 22') sized shop. I ran a 6" S&D pipe into and across the shop. Branched down to 4" pipe for the machines. The shortest and most direct connection is to the TS. There are permanent connections to The chop saw, shaper, Radial arm saw, jointer, and band saw. There is a ten foot hose on a connection that I float back and forth between the lunch box planer and the Performax. I also use the hose for the lathe, and as a shop vac.

Only the Performax and planer came with dust ports. The rest are too old. (I them days real woodworkers just inhaled the dust.)

As a one man shop I generally run one machine at a time. Sometimes two. I have the Long Ranger blast gates that turn the DC on when I open the gates. My DC is outside the shop in an outdoor closet.

All in all, I am very happy with the system. If I am busy in the shop, moving from machine to machine, I open the next gate before closing the last gate so as not to constantly turn the DC on and off. Sometimes I find I have several gates open. The improvement in the shop is enormous. I am astounded I used to work without the DC.

Congrats on your gloat.

Re: Dust Collection Questions *LINK*

#4

Re: Dust Collection Questions

Larry in NW Ohio

>Andy As Barry said, more or less, it`s better to go pretty much the biggest you can afford NOW and then grow into IT. otherwise you are going to fight the dust all the time and just mess with your small system and curse at it for not working right. The best you can do is buy the biggest you can afford, and go one size bigger. If you are going to be working with this DC for a LONG time you`ll never be sorry. I suggest the Oneida system. I`ve had their 3HP now for over 5 years and was never sorry. Your not to far from me, you are always wecolme to come down and look at mine if you want. I have my DC gates to open when I turn on my machine. Larry