Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

$^%@(*&^# RATS !

Posts

$^%@(*&^# RATS !

#1

Alan Young

$^%@(*&^# RATS ! 

Alan Young

>


img

Re: $^%@(*&^# RATS !

#2

Calm Down Allan

George@Colonel's Workshop-Havertown PA

>Allan, Good Evening and Calm Down,

Obviously you've successfully matched your initial mistake with considerable "stile". So quit railing. :<) Don't tell me its already glued up! That's a big ouch. Keep the doors for the next cabinet. What is the trite phrase? Been there, done that???? You'll be able to cope.

George

Re: $^%@(*&^# RATS !

#3

So-kay ! . . .

steve mackay

>back up, deep breaths !

Re: $^%@(*&^# RATS !

#4

Most of the fit is Pretty Good :

George@Colonel's Workshop-Havertown PA

>

Re: $^%@(*&^# RATS !

#5

Go to Lee Valley & order...

Craig in Silverdale

>a door frame stretcher.

Re: $^%@(*&^# RATS !

#6

Re: $^%@(*&^# RATS !

Fred Davis

>Looks like about one stile width proud, should be relatively easy to saw it down and refit , after you quit throwing things. ;-)0

FredD

Re: $^%@(*&^# RATS !

#7

Re: Go to Lee Valley & order...

Bob Entwisle in NJ

>Or if you can wait a couple weeks hold out for the rail retractor, I hear it's quite innovative in it's design and implementation.

Sorry for your pain and frustration....

Bob

Re: $^%@(*&^# RATS !

#8

I like the way

Dan Donaldson

>That you developed the arch shape for the front. Especially the shadow lines you put along the inside edges of the doors. ;-)

(ducking and running)

Re: $^%@(*&^# RATS !

#9

I Have The Same Kind of Tape Measure.

Ken Oakley-Sunny St. Cloud, Fla.

>Gotta get one that starts at zero instead of one.

Re: $^%@(*&^# RATS !

#10

So I'm thinkin'

Joanne in Point Pleasant, PA

>You did not intend this piece to have a bow front. :-)

No matter. We all measure twice and still measure incorrectly from time to time. Have Eileen make a nice tisane, calm your physick, and do as someone else suggested--cut it apart, remeasure and reglue. No one but yourself (well, and all of us!) will know.

Re: $^%@(*&^# RATS !

#11

George! You pun hog!

Joanne in Point Pleasant, PA

>

Re: $^%@(*&^# RATS !

#12

I think it's worse than...

David Yoho

>I think the problem's worse than anyone has noticed. The doors look just fine - it's the openings in the base cabinet that are wrong. Looks like you'll just have to make a new one, Alan!!!!!

David

Re: $^%@(*&^# RATS !

#13

Re: $^%@(*&^# RATS !

Jim Shaver - Oakville, Ont, Canada

>Hmmmmm, wood expands across the grain, neat experiment!

Re: $^%@(*&^# RATS !

#14

Measured it twice ?? Re: $^%@(*&^# RATS !

del schisler

>i bet you measured it from the wrong end? twice and dam it's still to long ? I bet most everbody has done that I know i have so you are not alone But i hate to make more door's del

Re: $^%@(*&^# RATS !

#15

Hey Alan.....

Thomas Skaggs, Foothills of Mount Level

>....that looks like it's gonna be a great piece! By the way, did you notice that the lower doors don't close?

Tom

Re: $^%@(*&^# RATS !

#16

I've never made that mistake.......

Bill Tindall, E.TN

>My "preference" is to forget to add the length for the tenons and the door comes out too narrow. At least your problem is fixable once you get over the annoying part. That looks to be a very nice cabinet!

Re: $^%@(*&^# RATS !

#17

Correction!

Thomas Skaggs, Foothills of Mount Level

>I looked at the picture again. The doors are just fine. It's the rest of the piece that is off. It's a shame, but I think you'll need to keep the doors and start the rest of that piece over. Sorry dude. Reality hurts.

Tom

Re: $^%@(*&^# RATS !

#18

WANTED - Cabinet stretcher :>(

GalenV in Iowa

>

Re: $^%@(*&^# RATS !

#19

I learnt my lesson once...

Brian in Brighton

>I did the same thing, but for twin cabinets. I read the best wisdom a while later. Make the doors after the cabinet is made.

At least you have enough length of the rails to cut them and remake the joint. Mine was 1/2 inch off, so I had to make new rails.

Brian in Brighton

Re: $^%@(*&^# RATS !

#20

Re: $^%@(*&^# RATS !

Wayne Allen (Carson City, NV)

>Alan -- I guess I can't figure out what all the fuss is about. I can't remember how many times I've done this sort of thing. Cut one of the stiles off and re-cut the rails to the proper width and then re-glue the stile back to the rails. When finished, you won't ever be able to tell it was re-done.

Re: $^%@(*&^# RATS !

#21

Alan Young

I think I was preoccupied with Stanley

Alan Young

>I made these doors last Saturday-all the while thinking about Game 1 of the Stanley Cup finals. My boys took me to the game and I was geeked all day. So I have decided woodworking and Hockey don't mix.

Alan

Re: $^%@(*&^# RATS !

#22

No excuses allowed Alan. You will have to........

Art Silva

>retrain for stoop labor. Happy hoeing!

Re: $^%@(*&^# RATS !

#23

Been there Done THAT

waroland

>I had to cut down some doors for a special cabinet I built for our kitchen TWICE. Man was I put out with myself, having built the whole kitchen without a noticabe mistake and then to do that on a special piece. That was several years ago and I still get mad when I look at that cabinet.