Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Milling Lumber *LINK*

Posts

Milling Lumber *LINK*

#1

Milling Lumber *LINK*

Grant in Iowa

>Recently a friend had several trees topped and uprooted by high winds. So we helped him get things cleaned up and in the process I was able to collect six logs that were sitable for milling in to lumber.

Four White Oak logs, and two Red Oak logs were moved to my friends driveway area from his woods. We used 100' of cable, a snatch block, and a homemade skid to move the logs. Power for moving them was provided by a 4WD Suburban, which had no trouble dragging even the largest of the logs up a 15% incline.

Once milled, the logs yielded 750 board feet of lumber, some common, but much of it nice clear boards.

I have attached a link to some photos I took of the milling operation. I wish there were more photos, but it was just the sawyer and I so I was pretty busy keeping up with him.

Lets see if this facebook link works:


Milling lumber

Re: Milling Lumber *LINK*

#2

nice logs

Bill Tindall, E.TN

>That is the kind of logs worth salvaging. Must have been some wind to topple a healthy oak. This is a difficult time of year to air dry oak . Keep the sun off it.

Re: Milling Lumber *LINK*

#3

Re: nice logs

AZ in Colorado Springs

>Cool. Nice pictures. And, now you've got a bunch of nice lumber! :+)

Re: Milling Lumber *LINK*

#4

Re: Milling Lumber

Fred Davis

>That's nicely stacked and stickered and if it was mine , I would not waste any time sealing the board ends.

Your air conditioned shop air will slurp the moisture out very fast , compared to having the stack outside and covered , so sealing in this case rates high on keeping the split ends down to a minimum

FredD

Re: Milling Lumber *LINK*

#5

Ellis Walentine

I'm wondering...

Ellis Walentine

>... about where all the moisture will go. The air conditioner will no doubt condense it and drain it away, but is this in any way hard on either the air conditioner or the shop? I've never stacked freshly milled wood in a shop. I usually cover it outdoors for several months first. What's the prevailing wisdom on this?

Ellis

Re: Milling Lumber *LINK*

#6

Re: I'm wondering...

John M in Mid Mich

>I know for DARNED sure not to bring fresh wet lumber into a NON-air conditioned shop. Just a few boards led to almost immediate layer of rust on the machines. Aargh. On the other hand, I did dry a big stack of elm once by temporarily building a "kiln" in the basement out of 1" foam board and powered by a small dehumidifier. "Successful" as an experiment, but it dried so quickly that I got surface checking. Wet elm in the basement was not an aroma that pleased the spouse, either.

Re: Milling Lumber *LINK*

#7

Dale Lenz

Re: The prevailing wisdom...

Dale Lenz

>is not to do that. Oak has something like 2# of water/bd.ft., green to dry. That's going to be somethings like 375 gal. of water to remove. That being said: several years ago, I got about 250 bd. ft. of hickory, a lot of sapwood, in August. Was concerned about sticker-stain. Put the green hickory in the shop and blew fan-air over the lumber while I was in the shop, maybe 30+ hours/wk. No stain, no rust, not sure if I kept the doors and window open or not. If I was Grant, I'd monitor the situation and act according. I'm with Fred, I'd seal the ends of the lumber.

Good looking wood there, Grant.

Re: Milling Lumber *LINK*

#8

possible problems

Bill Tindall, E.TN

>I didn't read how the lumber was to be dried. I am assuming by the comments it will be inside. Initially the problem will be getting it dry enough, quick enough, to prevent staining. The initial evaporation rate from a pile is huge. The air coming through a new pile feels cold from evaporation even on a hot day. If enough air is initially moved through the pile at a rate that will prevent staining a lot of water is going to need to go somewhere. Wet oak is not one of my favorite odors. Oak saw dust is especially corrosive. I wonder if the vapors are too? I would have put it outside, covered and shaded, until it lost some water.

Re: Milling Lumber *LINK*

#9

Points taken...

Grant in Iowa

>Gentlemen,

While I have been involved with harvesting lumber quite a bit in the past few years, I acknowledge that I am nowhere near expert on the subject.

My first choice would have been to place the lumber outside as well, but until I have a suitable place to put it (a fenced area, or secluded and shadded spot out of sight), that wasn't readily an option this time. The neighborhood type doesn't suit this solution just yet.

I am monitoring the humidity in the space as we speak, and as of yet, it is below that of the the humidity outdoors at around 40%. I should note that the space is 1400 square feet with a ten foot ceiling. If humidity becomes a problem in the coming days, I will either move the lumber, or open the overhead door as required to regulate the moisture.

I have dried lumber this way in the past with no apparent problems, albeit never more than 400 Bft at a time.

All of the logs were end sealed as soon as they were bucked to length.

Again, I will say that I respect and hear your concerns and will monitor and report as to the findings and any issues that result.

Regards,

Grant in Iowa

Re: Milling Lumber *LINK*

#10

water data

Bill Tindall, E.TN

>According to my NHLA rule book Northern oak will loose 1500 pounds/ 1000bdft going wet to dry. A typical drying schedule for off- the- saw oak is 30 days which translates to 50 pounds per day or 6 gallons per day. I would suppose one needs to obtain this rate, at least initially, to prevent stain. So, one needs to provide ventilation to obtain this rate, and what ever to deal with the evaporated water.

Off the topic at hand, I think a well stacked pile of oak in front of the garage is a lot better looking than most of the current crop of cars (that aren't selling).

Re: Milling Lumber *LINK*

#11

you did fine

Robin Corell in Atascadero CA

>White oak can be very dificult to dry when milled at this time of year. You need to provide enough air circulation to prevet mold staining but often the outside temps and beexes can be so high that you get excessive checking. the challenge is to find that sweet spot of temp and air circulation to prevent mold but not get checking. I think a well insulated and conditioned indoor space may actually be the best solution for a stack of white oak at this time of year. I would place an occellating fan on the far side of the room and aim it so that it dosen't blow directly on any part of the wood stack. this will stir up the air. moniter the middle of the sack to make sure this is sifficient. As the stack dries you will be able to more aggresively circulate the air.

Re: Milling Lumber *LINK*

#12

Re: Rate of Drying

Paul Leuba - Hunt Valley, MD

>30 days to air dry oak from the saw is a lot quicker than I previously believed. I had heard that it takes one year per inch of board.

In early April this year I purchased a poplar log and a maple log at a mill in southern PA. I had the logs sawed into 2" thick boards with a few 1" inchers where the boards became narrow. I stacked, stickered and covered the stack on a shady patio next to the house. The lumber felt very wet, but I do know its actual % because I just recently acquired a moisture meter. After just 6 weeks from the saw the stack tests at 14% on my meter. That amazed me because I was expecting something much higher based on my prior belief that it would take one year for each inch of thickness.

Paul in Hunt Valley, MD

Re: Milling Lumber *LINK*

#13

Thanks all...

Grant in Iowa

>I have taken everyones comments and concerns into account. I have been monitoring the humidity in the space, which did begin to rise a bit over the past 24 hours.

So I have begun a policy of ventilating the space at least twice daily in an effort to remove the large amount of moisture from the air. Watching humidity indoors and out and opening doors and windows when necessary.

No rust on the cast iron yet.

The air conditioner has been turned off now. It is a small one and isn't very effective given the open doors.

Regards,

Grant in Iowa